Installation Guide for MODE models including: KS1460, KS1460 Multi Sided Gas Fireplace, Multi Sided Gas Fireplace, Sided Gas Fireplace, Gas Fireplace, Fireplace
CAUTION - PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALL KS1460 Corner/Peninsula MULTI SIDED GAS FIREPLACE Installation Instructions for Kitset Wall Unit (KWU) 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Applies to: KS1460 Corner LH, KS1460 Corner RH, KS1460 Peninsula KWU Information The Kitset Wall Unit (KWU) is consisted of metal support brackets attached to timber framing. The KWU is considered to be an integral part of the fireplace and may not be installed without it. The KWU is designed to sustain up to 500kg of vertical loading. NOTE/WARNING: ONLY THE METAL SUPPORT BRACKETS ARE PROVIDED (PARTS HIGHLIGHTED IN GREY BELOW). THE TIMBER FRAMING WILL HAVE TO BE CONSTRUCTED ACCORDING TO THE DIMENSIONS IN THE FOLLOWING SECTION. PACKAGE CONTAINS: · 28x 302066 8G X 5/8 WAFER HEAD SELF TAPPER PHILIPS BLK · 2x 302065 M5 x 25 MACHINE SCREW PAN POZI ZP · 2x G9007 Washer M6 X 19 KS1460 CORNER-PENINSULA KWU HOLDING BRACKET KS1460 CORNER-PENINSULA KWU SIDE PLATE KS1460 CORNER-PENINSULA KWU FRONT PLATE KS1460 CORNER-PENINSULA KWU SIDE PLATE KS1460 CORNER-PENINSULA KWU FRONT PLATE 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula KWU Information (Continued) KWU Dimensions 111mm 1853mm OVERALL 459mm OVERALL 263mm 1423mm 453mm INTERNAL CLEARANCE (SIDE TO SIDE) 302mm 1060mm BASE FRAME TO TOP FRAME 1200mm OVERALL 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula KWU Information (Continued) KWU with KS1460 Corner LH & RH Models The following dimensions are needed to allow for correct wall lining thickness and clearance behind the appliance when installing the KS1460 Corner models: FOR KWU INSTALLED WITH KS1460 CORNER MODELS KWU SIDE BRACKET A TO KS1460 STANDARD TRIM 22mm B KWU SIDE BRACKET TO KS1460 CORNER BACK PANEL 9mm DETAIL A DETAIL B C D KWU FRONT PLATE (TOP) TO KS1460 STANDARD TRIM 22mm DETAIL C DETAIL D KWU FRONT PLATE (BOTTOM) TO KS1460 STANDARD TRIM 22mm 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula KWU Information (Continued) KWU with KS1460 Peninsula Model The following dimensions are needed to allow for correct wall lining thickness and clearance behind the appliance when installing the KS1460 Peninsula model: FOR KWU INSTALLED WITH KS1460 PENINSULA MODELS A B KWU SIDE BRACKET TO KS1460 STANDARD TRIM 22mm KWU SIDE BRACKET TO KS1460 STANDARD TRIM 22mm DETAIL A DETAIL B C D KWU FRONT PLATE (TOP) TO KS1460 STANDARD TRIM 22mm DETAIL C DETAIL D KWU FRONT PLATE (BOTTOM) TO KS1460 STANDARD TRIM 22mm 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Timber Framing and Plywood Dimensions The following timber framing dimensions is required to build the KWU. Please cut timber pieces for framing according to the cutlist listed below and fix the timber pieces together to build the KWU framing. NOTE: Ensure that the timber pieces used to construct the framing are straight and not warped. Base Frame Please use 45mm X 45mm (nominal) framing timber to construct the base frame. Build the frame to the OUTER DIMENSIONS in the images below: (Frame Dimensions: 1850mm x 453mm x 45mm) 1850 995 480 45 330 453 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Timber Framing and Plywood Dimensions (Continued) Base Panel Please use a 9mm plywood or a similar material for the panel and cut according the dimensions shown in the diagram below. 1520 453 End Frame Please use 90mm X 45mm(nominal) framing timber to construct the end frame. Build the frame to the OUTER DIMENSIONS in the images below: (Frame Dimensions: 1065mm x 453mm x 90mm) 453 90 FRAMING IS SYMMETRICAL 1065 510 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Timber Framing and Plywood Dimensions (Continued) Top Frame Please use 90mm X 45mm (nominal) framing timber to construct the top frame. Build the frame to the OUTER DIMENSIONS in the images below: (Frame Dimensions: 1850mm x 453mm x 90mm) 1850 480 45 480 453 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions Note: Please ensure all timber framing and plywood pieces have been cut and constructed before assembling the KWU. Ensure timber screws and fasteners are placed in spots where they will not collide with one another. STANDARD PROCEDURE: Warning: For installation scenarios where the back of the fireplace is/will be inaccessible, please refer to the next section - "PROCEDURE FOR SCENARIOS WITH AN INACCESSIBLE BACK SIDE": 1. Place the base frame on the floor or a raised platform according to the orientation indicated below. Secure base frame to the floor or platform using suitable anchors. POWER CABLE AND FLUING LOCATED ON THIS END END GLASS OF THE FIRE LOCATED ON THIS END 2. Install and fix base panel onto the base frame. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 3. Place KS1460 fireplace onto base frame. Align the end of the base frame with the appliance base of the fireplace, as indicated below. END OF CHASSIS IN LINE WITH EDGE OF BASE FRAME 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 4. Place and secure the end frame on to the base frame with wood screws. Align rear of the end frame with the outer end of the base frame (as indicated below). Secure the end frame to an adjacent with sesimic restraining fasteners. NOTE: Before the side plates are attached, please make sure that the electricity, gas and flue components have been connected along with the power flue cable and home automation cable, if applicable. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 5. Place the side metal KWU panels on the front and back of the fire. The panel ends must align with the rear of the end frame and the ends of the base frame. Secure the side metal plates to the timber framing with wood screws. On each of the side metal plates, use the provided wafer head screws (low profile head) to secure the plates to the chassis lid and the chassis base. NOTE: Before the side plates are attached, please make sure that the electricity, gas and flue components have been connected along with the power flue cable and home automation cable, if applicable. REPEAT PROCEDURE ON BOTH SIDES A D REPEAT PROCEDURE ON BOTH SIDES B D C DETAIL A REPEAT PROCEDURE ON BOTH SIDES DETAIL C DETAIL D 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 6. Place and secure the top frame on to the end frame with wood screws. Align the outer end of the top frame with the rear of the end frame. Secure the side metal brackets to the top frame with wood screws. REPEAT PROCEDURE ON BOTH SIDES 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 7. Place the KWU-chassis lid bracket on the top frame. Ensure the bracket holes are aligned with the nuts in the chassis lid. Leave a 10mm gap between the chassis lid and the KWU bracket. Using wood screws, secure the bracket to the top timber frame through the four predrilled holes on the sides of the bracket. Attach the provided M5 screws and washers through the holes on the KWU-chassis lid bracket to level the chassis lid. CLOSE-UP VIEW OF BRACKET SCREW UP OR DOWN TO ADJUST TILT 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 8. Attach end metal brackets on to the top frame and base frame to complete the KWU installation. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions PROCEDURE FOR SCENARIOS WITH AN INACCESSIBLE BACK SIDE: 1. Place the base frame on the floor or raised platform according to the orientation indicated below. Warning: PLEASE DO NOT FIX THE BASE FRAME TO THE FLOOR IN THIS STEP. POWER CABLE AND FLUING LOCATED ON THIS END END GLASS OF THE FIRE LOCATED ON THIS END 2. Install and fix base panel onto the base frame. Warning: PLEASE DO NOT FIX THE BASE FRAME TO THE FLOOR IN THIS STEP. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 3. Place a side metal KWU panels on what will be the inaccessble back side of the fire. The panel ends must align with the rear of the end frame and the ends of the base frame. Secure the side metal plate to the timber framing with wood screws. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 4. Place and secure the top frame on to the end frame with wood screws. Align the outer end of the top frame with the rear of the end frame. Secure the side metal brackets to the top frame with wood screws. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 5. Position the KWU in its required location, then secure the base frame to the floor or platform using suitable anchors. 630740_1 Kitset Wall Unit (KWU) Installation Instructions MODE KS1460 Corner & Peninsula Installation Instructions 6. Place KS1460 fireplace onto base frame. Align the end of the base frame with the appliance base of the fireplace, as indicated below. Note: After this step, please complete the KWU installation by following Step 5, Step 7 and Step 8 of the Standard Procedure, in this exact order. END OF CHASSIS IN LINE WITH EDGE OF BASE FRAME 630740_1Adobe PDF Library 17.0 Adobe InDesign 19.5 (Windows)