LogiCO2 O2 Mk9 Detector Sensor
Маълумот оид ба маҳсулот
Мушаххасоти
- Model: O2 Sensor Kit Mk9
- Таъмини барқ: 24Vdc
- Истеъмоли кунунӣ: 38мА
- Кишвари пайдоиш: Шветсия
ГЕНЕРАТОРХОИ АЗОТ
Лутфан таваҷҷӯҳ намоед, ки агар генератори нитроген дар минтақае, ки сенсори O2 насб шудааст, истифода шавад, оксигени зиёдатии аз ҷониби генератори нитроген тавлидшуда бояд аз минтақа берун карда шавад. Агар оксиген берун набарояд, дар минтақа истифода бурдани сенсори O2 иҷозат дода намешавад.
Калибрченкунӣ
Сенсори LogiCO2 O2 дорои функсияи худкори калибрченкунӣ мебошад, ки ҳамчун стандарт фаъол карда шудааст ва дар шароити муқаррарӣ ҳеҷ гуна калибрченкунии дастӣ лозим нест.
Баландии насб
Сенсори O2 бояд дар баландии нафаскашӣ, дар масофаи 150-180 см/5-6 фут аз фарш насб карда шавад.
Try to find an installation position where the unit is least likely to be damaged. Mount the O2 sensor with supplied mounting screws. The horn/strobe/s must be installed on the wall above the O2 sensor, approximately 2-2.4 m/80-96 inches (as per NFPA 72) above the floor, clearly visible from any entrance of the area being monitored.
Коридорҳо
In areas where the Nitrogen or mixed gas are stored at the end of a corridor, it is paramount to place an extra Horn Strobe at the entrance of the corridor. This to give an early warning in case of a Oxygen depletion.
Lower floor/basement
In areas where the Nitrogen or mixed gas is stored or distributed in Below Grade locations such as Lower Floors and Basements, it is essential to have Horn Strobes before the entrance to the area.
Enclosed Spaces
In enclosed spaces Horn Strobes must be placed outside of each entrance.
Насби система
Installing an O2-kit to an existing LogiCO2 Mk9 CO2 Safety System
Since you are adding an additional sensor to the system, you need to set the correct ID-settings for the sensors and the central unit. This is done using the dip switches.
The O2 sensor in the kit is set to ID2 as standard, if you only have one CO2 sensor connected in the sys-tem, you only need to change a dip switch in the central unit. Unscrew the screws and remove the lid of the central unit. Then put dip 1 in the ON position.
If you have 2 or more sensors already connected in the alarm system, please check the User´s manual.
Схемати насб
LogiCO2 International • P.B. 9097 • 400 92 Gothenburg • Sweden www.logico2.com • info@logico2.com
Саволҳои зуд-зуд пурсидашаванда (FAQ)
- Q: Do I need to manually calibrate the O2 sensor?
A: No, the O2 sensor has an automatic self-calibration function and does not require manual calibration under normal conditions. - Q: What is the recommended installation height for the O2 sensor?
A: Сенсори O2 бояд дар баландии нафаскашӣ, дар масофаи 150-180 см/5-6 фут аз фарш насб карда шавад. - Q: How do I add an O2 sensor to an existing LogiCO2 Mk9 CO2 Safety System?
A: To add an O2 sensor, set the correct ID-settings for the sensors and central unit using dip switches. The O2 sensor in the kit is set to ID2 as standard.
Ҳуҷҷатҳо / Сарчашмаҳо
 |
LogiCO2 O2 Mk9 Detector Sensor [pdf] Дастури корбар O2 Mk9 Detector Sensor, O2 Mk9, Detector Sensor, Sensor |
