Нишони Honeywell

H-Class - logo

HD Peel & Present Option

Honeywell OPT78-2627 H-Class Powered Internal Rewind Option - detamexright by our customers.

Honeywell OPT78-2613-04 H-Class Thermal Transfer Option

дар болоиview

This document describes the contents, installation, and use of the Heavy Duty Peel and Present option for the H-Class printer. After verifying the contents of the kit and the tools needed, follow the steps below to install and begin using the option. A maintenance procedure is also included, so keep this documentation for future reference.

Огоҳӣ огоҳӣ
For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.

Contents of the Heavy Duty Peel and Present Option

This kit contains the following item:
• Heavy Duty Peel and Present Assembly

Honeywell H-4310 H-Class HD Peel and Present Option - Heavy Duty Peel and PresentВоситаҳои зарурӣ
To install this option, you will need a standard screwdriver.

Step 1: Preparing the Printer

A) Turn ‘Off’ the Калиди барқ and unplug the power cord from the AC Receptacle.

Honeywell H-4310 H-Class HD Peel and Present Option - Preparing the Printer

B) Ба поён пахш кунед Сайд, then pull forward to remove the Дар.

Honeywell H-4310 H-Class HD Peel and Present Option - DoorC) Баланд бардоштани Сарпӯши дастрасӣ and remove your media from the printer.

Honeywell H-4310 H-Class HD Peel and Present Option - Access Cover

D) Хориҷ кунед Нақша ва Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)

Step 2: Installing the Heavy Duty Peel and Present Assembly

A) Пахш кунед Дастгоҳ ва кушодани Peel and Present Маҷлис.

Honeywell H-4310 H-Class HD Peel and Present Option - Present Assembly

B) Carefully press the Peel and Present Assembly ба дар Front Plate Connector.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present

C) Пурзӯр кунед Винти насб таъмин намояд Peel and Present Assembly ба чопгар.

Step 3: Using the Option
During operation, labels will be peeled from the backing material and dispensed “on-demand” – that is, subsequent printing will occur only after a previously printed label has been removed from the printer. As a reminder, “REMOVE LABEL” will be displayed to prompt you when a label awaits removal.

Begin using the option as follows:

A) сарборӣ Медиа (see the Operator’s Manual for details). Extend 20 inches (50 cm) of Медиа from the printer.

Honeywell H-4310 H-Class HD Peel and Present Option - Media

B) Remove the labels from this extended portion of media, leaving only the Backing Material. Crease the leading edge of this BackingMaterial.
C)
Route the Маводи дастгирӣ дар зери Assist Roller ва Internal Rewinder.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing

D) Печондан Маводи дастгирӣ in a counterclockwise direction around the Rewinder Hub and insert the creased leading edge into one of its Slots. Insert the Media Clasp (Item 6) into the Slot over the creased leading edge of the Баргардонидани Material and around the Rewinder Hub.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing Material

E) Пӯшед Peel and Present Assembly. Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present Assembly

F) Боварӣ ҳосил кунед ТАЙЁР is displayed on the Front Panel then press the FEED Key and proceed according to your observations:

  • If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
  • If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”

Honeywell H-4310 H-Class HD Peel and Present Option - Front Panel

Эзоҳ:

  1. The operation of the Present Sensor on this option can also be controlled by host software commands, so ensure that your labeling program is properly configured for use when sending label formats to the printer.
  2. If this option is removed with power applied, the printer will behave as if a label awaits removal; to restore normal operation, cycle power to the printer.

Step 4: Configuring the Printer

While the Heavy Duty Peel and Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:

Шарҳ: In the following procedure, consult the Operator’s Manual for detailed front panel instructions.

A) Пахш кунед МЕНЮИ Button on the printer’s front panel.
B) бо истифода аз DOWN Button, scroll to PRINTER OPTIONS then press the Right Button.
C) бо истифода аз DOWN Button, scroll to PRESENT SENSOR пас фишор диҳед ENTER Key.
D) бо истифода аз DOWN Button, scroll to Модели пас фишор диҳед ENTER Key.
E) бо истифода аз DOWN Button, scroll to худкор пас фишор диҳед ENTER Калид.
F) Пахш кунед БАРОМАДГОҲ Key then, at the Тағиротро захира кунед? интихоб кунед, интихоб кунед ҲА барои ба итмом расонидани насб.
G) Turn the Power Switch 'Хомӯш' ва 'фаъол' to reset the printer and complete the configuration.

Шарҳ: If the printer fails to separate the labels from the backing material, and the Internal Rewinder is not turning, it may need to be enabled. Using the procedure above as a guide, press the МЕНЮИ Button, scroll to PRINTER OPTIONS, баъд ба REWINDER, ва интихоб кунед АВТО. Afterward, press the БАРОМАДГОҲ key and save your changes when prompted.

Maintaining the Heavy Duty Peel & Present Assembly

To ensure trouble-free operation, the Heavy Duty Peel and Present Assembly should be cleaned after every 100,000 inches (254,000 cm) of media use. This interval depends on the label adhesive, where “gummy” adhesives may require more frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS → MEDIA COUNTERS in the printer’s menu system.)

Clean the assembly as follows:

  1. Turn ‘Off’ the Power Switch and unplug the power cord from the AC Receptacle. Raise the Access Cover and remove the media from the printer.
  2. Remove the Peel & Present Assembly from the printer.
  3. Using compressed air or a soft brush, clean the санҷанда on the assembly.Honeywell H-4310 H-Class HD Peel and Present Option - SensorsШарҳ: For cleaning heavy deposits, isopropyl alcohol can be used – provided it is carefully applied using a cotton swab, and then allowed to dry before reconnecting the option to the printer.
  4. Пахш кунед Дастгоҳ to open the Peel and Present Assembly. Then remove the C-клип that secures the Upper Roller Shaft ба Front Cover.Honeywell H-4310 H-Class HD Peel and Present Option - Front Cover
  5. Remove the Upper Roller Shaft and the associated Rollers.Honeywell H-4310 H-Class HD Peel and Present Option - Rollers
  6. Истифодаи a Swam Pam dampened with alcohol, wipe all ғалтаки ва Upper Roller Shaft surface clean. Pay special attention to the ridges on the Роллерҳо to ensure that they are clean.
    Шарҳ: For cleaning heavy deposits from the Rollers and Shafts in the following steps, WD-40 or another non-damaging adhesive remover can be substituted for isopropyl alcohol – provided this adhesive remover is carefully applied using a cotton swab.
  7. Слайд кунед Роллерҳо бозгашт ба Upper Roller Shaft, place the components into the Front Cover, and reinstall the C-Clip.
  8. Тела ва Асфал ҳарду ҷадвалбандиҳоро ки таъмин менамояд Lower Roller Assembly to the Front Cover (as shown) and then, while keeping it intact, carefully remove the entire Lower Roller Assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Tabs
  9. Take note of the individual ғалтаки positions – they must be reinstalled in the same order – then, carefully remove the Роллерҳо аз Lower Roller Shaft.Honeywell H-4310 H-Class HD Peel and Present Option - Lower Roller Shaf
  10. Истифодаи a Swam Pam dampened with alcohol, wipe all ғалтаки ва Lower Roller Shaft surfaces clean. Pay special attention to the ridges on the Роллерҳо to ensure that they are clean.
  11. Слайд кунед Rollers, in their original order, onto the Lower Roller Shaft and reinstall them in the Front Cover, таъмини ки ҷадвалбандиҳоро are properly seated. Reinstall the Peel and Present Assembly onto the printer to complete the cleaning procedure.

Ҳуҷҷатҳо / Сарчашмаҳо

Honeywell H-4310 H-Class HD Peel and Present Option [pdf] Дастурҳо
H-4310, H-Class, HD Peel and Present Option, H-4310 H-Class HD Peel and Present Option

Эзоҳ диҳед

Суроғаи почтаи электронии шумо нест, нашр карда мешавад.