3 BSD Blind Spot Smart Ambient Light
“
Product Information
Specifications:
- Compatible Models: Model 3 (2017-2020.10), Model 3
(2021-2023.7), Model Y (2020-2025.2), Highland Model 3 (2023.8+),
MY Juniper (2025.3+) - Components: 1 Light Strip, 3 Upgrade Line, 2 Power Cord
Harness, 4 Prying Board - Installation Tools: Gloves, Installation Precautions, Turn off
Screen Power for Operation
Product Usage Instructions
Installation Steps for INT Version (applicable to Model 3 –
2017-2020.10):
- Remove the door edge strip and pry open the baffle.
- Pry open the snap.
- Remove the guard plate.
- Plug in the corresponding OBD power cord properly. (Note: INT
version has only one plug.) - Thread the wire and pull the wrapped wire over.
- Connect the wires properly, organize them, and cover the
baffle. - Find 3 centimeters away from the air outlet.
- Break open the baffle a little and insert the light strip.
- Push it along the air outlet, align the edges, and press it in
place. - Check the effect after installation.
Installation Steps for AMD Version (applicable to Model 3 –
2021-2023.7 and Model Y – 2020-2025.2):
FAQ – Frequently Asked Questions
Problem: The light strip is not working
Reason: The plug is not installed properly or
was pulled and bent.
Solution: Check the position of the plug
according to the installation video. Avoid pulling or bending the
light strip forcefully to prevent damage.
Problem: Some of the light strips are not lit
Reason: The light strip is made of soft
silicone with built-in LED beads.
Solution: Do not pull or bend it forcefully to
avoid damaging the light strip.
Warranty and Support
Tesstudio offers a 1-year extended warranty. Send your customer
number to receive a full 1-year warranty. Contact Email:
service@tesstudio.com
“`
Parts list
Part list diagram
1.
1 Light strip
3 Upgrade line
2 Power cord harness 4 Prying board
1.
2.
3. 4.
int version, applicable to Model3(2017- October 2020)
2.
3.
4.
AMD version, applicable toModel3(2021-2023.7) ModelY(2020-2025.2)
1. Tools required for installation Gloves Two, installation precautions Turn off the screen power for operation
Tip: In order to install more quickly, be sure to read the instructions carefully.
Parts list
Part list diagram
3. 1.
2. 4.
Highland Model 3(2023.8+) Model Y Juniper(2025.3+)
1 Light strip
3 Upgrade line
2 Power cord harness 4 Prying board
1. Tools required for installation Gloves Two, installation precautions Turn off the screen power for operation
Tip: In order to install more quickly, be sure to read the instructions carefully.
Model 3 /Model Y/Highland Model 3/MY Juniper BSD Blind Spot Smart Ambient Lighting Installation Instructions – Disclaimer and Notes
Warnings and Disclaimers
Important notice: Welcome to purchase the company’s products, in order to protect the legitimate rights and interests of users, in this special reminder to users, please be sure to carefully read and fully understand the terms of this statement before using this product.If you use this product, your use of the behavior will be regarded as the acceptance of the entire content of this statement, and agree to accept the following terms of this statement, and bear the effect caused by irregular use.Company reserves the right to update the above documents.Please be sure to follow the instructions to operate this product.
Installation Manual
Model 3/Model Y
Installation Video
Caution
1. Check whether the product list is complete and damaged before installation. 2, The installation instructions may be slightly different from the actual operation. If there is any difference, please refer to the actual situation or contact us. 3, Warning: do not disassemble any parts by yourself, any improper operation will not be covered by the warranty. 4, Install the product first watch the installation video and instructions. 5, check whether the installed product function is normal. 6. All models of this product are common. The installation procedures for the models shown in the installation manual are slightly different for other models of Tesla. Please install according to actual conditions or contact us.
Highland Model 3/MY Juniper
Installation Video
Customer Service : phone : +1(626)412-7352
+1 7143179647 Email: service@tesstudio.com
int version, applicable toModel3(2017-2020.10)
AMD version, applicable toModel3(2021-2023.7) ModelY(2020-2025.2)
The installation method is as follows
1Remove the door edge strip and pry open the baffle
2Pry open the snap
3Remove the guard plate
4Plug in the corresponding OBD power cord properly Note: The INT version has only one plug
5Thread the wire. Pull the wrapped wire over
6Connect the connecting wires properly, organize the wires, and cover the baffle
7Find 3 centimeters away from the air outlet
8Break open the baffle a little and insert the light strip
9Push it all the way along the air outlet, align the edges and press it in place
10Effect after installation
BSD
The installation method is as follows
1Find 3 centimeters away from the air outlet
2Tear off the adhesive tape and break the baffle a little
3Stick it all the way along the air outlet
4Align along the edges and press to fix
5When prying open one side of the baffle, there is no need to fully open it
6Remove the door edge strip and pry open the baffle
7Remove the door edge strip and pry open the baffle
8Thread the wire. Pull the wrapped wire over
9Connect the connecting wires properly, organize the wires, and cover the baffle
10Remove the latch and find the connection socket
11Unplug the pin and connect our module back
12Power-on test
13Hide the lines well and reinstall them step by step
14Effect after installation
BSD Blind Spot Smart Ambient lighting-Troubleshooting Guide for Frequently Asked Questions
“Problem”
Reason
The light strip is not working
Some of the light strips are not lit
The plug is not installed properly It was pulled and bent
Solution
Check the position of the plug according to the installation video The light strip is made of soft silicone with built-in LED beads. Do not pull or bend it forcefully to avoid damaging the light strip.
Warranty and Support
Tesstudio offers a 1 – year extended warranty Send us your customer number to receive a full 1 – year warranty Email: service@tesstudio.com
Our Website:tesstudio. COM Designed by TESSTUDIO
Documents / Resources
 | TESSTUDIO 3 BSD Blind Spot Smart Ambient Light [pdf] Installation Guide Model 3 2017-2023.7, Model Y 2020-2025.2, Highland Model 3 2023.8, MY Juniper 2025.3, 3 BSD Blind Spot Smart Ambient Light, BSD Blind Spot Smart Ambient Light, Blind Spot Smart Ambient Light, Spot Smart Ambient Light, Ambient Light |