TENETH V9 Pro Cutting Plotter User Manual

TENETH V9 Pro Cutting Plotter

Packing list

1. Cutter carriage
   Control the knife to cut the film sheet
2. Rubber wheels
   Work with steel axis to keep cutting without slip
3. Steel axis
   Work with rubber wheels to fix and protect film sheet
4. Power switch
   Turn on the machine. Press it lightly to turn back the films during stand-by
5. Switch for blade holder installation
   Press lightly to open the cover
6. Film feeding sensor
   Auto feeding the film after detecting it
7. Film pasting guide
   Please paste the films based on the guide
8. Blade holder installatin port
   Open the port to take out or install the blade holder
9. High definition screen
   6 inch touch screen , built in operation system
10. Power connection port
    External 24v power port
    Blade installation
11. Handle
    Press it to get the blade
12. Gear
    Adjust the blade tip length
13. Blade handle holder
    To be fixed by the hole in cutting head
14. Cutting Blade
    Cutting film sheet

Notes:
Ajust the blade:
Twist the gear to adjust the blade tip Value bigger,tip longer
Value smaller, tip shorter Factory setting is gear 6

Change blade:
Press ha11ndle
take out the old blade put a new one in it

Blade holder installation

Install the blade holder

• Press the button to open the entrance
• Open the fixed handle
• Insert the holder to hole straightly
• Fix the handle

Power on / off

Connect the cable and adapter. 110-240VAC po wer for the plug connection. The adapter connects the machine Press the power button, machine powers. ttakes 30s for starting.

Material installation

Put the material on the table flatly and align left based on the feeding guide
The material will be fed automatically after the cutterdetect it.

WIFI Connection

Note: Connecting succeeds, the wifi ID will be shown beloW, if not, you may need insert the correct password and connect.

Login account
After connecting wifi, choose login and ins ert the account and choose version, then insert your password to login the data page..
Account and password may paste on the bottom of the cutter or you can get from your supplier

Choose Cutting Data

Cutting finished

The sheet will be dropped out automatically after cutting finished, please take out the finished parts and paste on the phone.

Parameters and precautions

Parameters

1. Connection wifi or Bluetooth
2. Internal Power DC24V 1.75A
3. Machine size 420*123*163mm
4. Machine weight 4.3kg

• Don’t toouch the knife tip by finger
  The finger may be hurt by the knife tip
• Don’t seep into liquid
  This may cause fire or electric shock
• Don’t use non-original power supply
  This may damage the cricuit or electric shock
• Don’t use in thunderstorm days
  This may damage the machine
• Don’t use the non-standard materials
  Please cut the standard size of material to reach the.perfect.result..

Product parameters and precautions 

• Press power switch for emergency stop during working.
• Forbid moving the carriage by hand after connecting the power to avoid machine damage.
• Knife is a consumable part, please change to a new one if it is dull.
• Press the power switch in 3 seconds continually to turn off the cutter, forbid taking out the power cable directly to turn off the machine because it will damage the mainboard

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received including interference that may cause undesired operation.

FCC Warning
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
  from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. 15

To maintain compliance with FCC’s RF Exposure guidelines,
This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.