Panoramic Camera

79442-180 Installation Guide
Included in this Product Package:

TEKVOX 79442-180 180° 4K Panoramic Camera A01                                           TEKVOX 79442-180 180° 4K Panoramic Camera A02
A. Mount Stem (x1)                        B. Mount Base (x1)

TEKVOX 79442-180 180° 4K Panoramic Camera A03                     TEKVOX 79442-180 180° 4K Panoramic Camera A04
C. Panoramic Camera (x1)           D. #6 Wood Screw (x4)

TEKVOX 79442-180 180° 4K Panoramic Camera A05                                    TEKVOX 79442-180 180° 4K Panoramic Camera A06
E. #6-32 Hex Screw (x1)                    F. USB Cable (x1)

Step 1: Choose Mounting Location

TEKVOX 79442-180 180° 4K Panoramic Camera B01

This camera mount requires a 6″ square of clearance for proper installation. The mounting location should be a clear, flat surface on the presenter desk/podium. Ensure that location is behind any monitors, and that nothing else taller than 10″ is between the mounting location and the audience.

Step 2: Drill Cable Routing Hole

TEKVOX 79442-180 180° 4K Panoramic Camera B02

In center of chosen mounting location, drill a ¾” hole through the podium/desk for routing cables. Remove any splinters and sharp edges that could damage cables.

Step 3: Screw Mount Base onto Podium/Desk

TEKVOX 79442-180 180° 4K Panoramic Camera B03

Using the four (4) provided wood screws (D, in camera mount box), attach the camera mount base (B) to the desk/podium, making sure that it is centered on the hole drilled in Step 2, and that the cable pass through notch is facing away from the audience.

Step 4: Screw Mount Stem onto Base

TEKVOX 79442-180 180° 4K Panoramic Camera B04

Screw threaded end of camera mount stem (A) into the central hole of the camera A mount base (B), tightening until snug.

Step 5: Extend Camera Mount to Desired Height

TEKVOX 79442-180 180° 4K Panoramic Camera B05

1. Loosen the bottom-most of the two black rings near the top of the stem by turning it counter-clockwise.
2. Lift the upper portion of the stem until the top of the mount vertically clears any potential obstructions, and is as close as possible to even with the tops of audience members’ heads.
3. Face rectangular cable pass through hole in stem away from audience, then re-tighten bottom black ring until snug.

Step 6: Turn Mounting Screw to Face Upwards

TEKVOX 79442-180 180° 4K Panoramic Camera B06

1. Holding the upper part of the camera mount stem (A) to keep it from rotating, loosen the top-most of the two black rings by turning it counter-clockwise.
2. Turn the mounting screw to face upwards.
3. Re-tighten the upper black ring to lock it in place.

Step 7: Mount Camera

TEKVOX 79442-180 180° 4K Panoramic Camera B07

1. Remove plastic cap from mounting screw on top of camera mount stem (A).
2. Screw mounting screw into the most central threaded hole on the bottom of the panoramic camera (C), tightening until snug.

Step 8: Position Camera to Face Audience

TEKVOX 79442-180 180° 4K Panoramic Camera B08

1. Holding the upper part of the camera mount stem (A) to keep it from rotating, loosen the top-most of the two black rings by turning it counter-clockwise.
2. Turn panoramic camera (C) to face Hold center of audience. Make sure that camera is level and vertically centered on the audience’s heads.
3. Once camera is in position, re-tighten the upper black ring to lock it in place.

Step 9: Route USB Cable Through Mount to Camera

TEKVOX 79442-180 180° 4K Panoramic Camera B09

1. Pass USB-C end of USB cable (F, in camera box) up from underneath desk/podium, through camera mount (A/B), and out rectangular cable pass through hole (oriented away from students in Step 5). Carefully feed cable from both ends and work slowly to avoid damaging the cable on sharp metal edges.
2. Connect to USB 2.0 Device port on Panoramic Camera (C), making sure that the cable is not bending sharply. Connect USB-A end of cable as indicated in system schematic and on cable label.

Step 10: Test System

Once all other components of system have been fully installed and connected, test system to confirm that it functions as expected. Confirm that camera image is not tilted or distorted in any way, and that camera can be accessed by all compatible video conference hosts via USB connection.

Step 11: Tighten Hex Locking Screw

TEKVOX 79442-180 180° 4K Panoramic Camera B10

Using a 5/64″ hex wrench, tighten the small black screw on the upper black ring of the camera mount stem (A) until snug. NOTE: The screw will NOT go all the way in; do not over tighten.

www.tekvox.com

Documents / Resources

TEKVOX 79442-180 180° 4K Panoramic Camera [pdf] Installation Guide
79442-180, 180 4K Panoramic Camera, Panoramic Camera, 180 4K Camera, Camera, 79442-180 Panoramic Camera

References

Leave a comment

Your email address will not be published. Required fields are marked *