Cell2 Manuals & User Guides

User manuals, setup guides, troubleshooting help, and repair information for Cell2 products.

Tip: include the full model number printed on your Cell2 label for the best match.

Cell2 manuals

Latest posts, featured manuals, and retailer-linked manuals for this brand tag.

cell2 B18 LED Beacon User Manual

February 26, 2023

cell2 B18 LED Beacon INSTRUCTION WIRING RED: To +VDC BLACK: To Chassis Ground(-) FLASH PATTERN SELECTION Open: Twist the dome lens counter clockwise O , then lift the dome lens to open. Change: While activating Warning Mode, momentarily push the…

Brand: Cell2

Cell2 Microbar EX Mini LED Lightbars User Manual

February 26, 2023

Cell2 Microbar EX Mini LED Lightbars Overview WARNING: Do not look directly into LEDs while in operation; may cause momentary blindness and/or eye damage. FLASH PATTERNS Momentarily apply +VDC to BLUE: Once for the next pattern Quickly 3 times for…

Brand: Cell2

Cell2 Microbar EXD Mini LED Lightbars User Manual

February 26, 2023

Cell2 Microbar EXD Mini LED Lightbars Auto-Dimming Light Sensor Automatically activate or deactivate the Low-Power operation. Application to Colour 1. IMPORTANT: Do not cover the light sensor or place the minibar under vehicle shad (Auto-dimming may not function properly). 2-Button…

Brand: Cell2

Cell2 MINI-FALCON 1-Bolt Mount Minibar User Manual

February 26, 2023

Cell2 MINI-FALCON 1-Bolt Mount Minibar WIRING/OPERATION 4-Wire Cable 2-Button Cigar Plug FLASH PATTERNS (Split) Left-half alternating Right-half. To maintain ECE R65 compliance use flash pattern 1 (Double) Activating the dim function will invalidate the R65 approval. INSTALLATION (Actual Mounting Kit…

Brand: Cell2

cell2 LP4 LED PAD User Manual

February 26, 2023

cell2 LP4 LED PAD User Surface Mount (All heads should be set to the same pattern) NOTE: To obtain optimum adhesion, the surfaces must be clean, dry and well unified For Simultaneous or Alternating Flash Apply +VDC to WHITE and…

Brand: Cell2

Cell2 B14 Magnetic Mount Coil User Manual

February 26, 2023

Cell2 B14 Magnetic Mount Coil Permanent Mount WIRING RED: To +VDC for Cruise Mode BLACK: To Chassis Ground (-) RED + \WHITE: To +VDC for Warning Mode Y OW: Flash patterns & Synchronization Connect YELLOW wires of all unit together…

Brand: Cell2

cell2 86-M4310-0011.0 Mini Lighthead Instruction Manual

February 26, 2023

cell2 86-M4310-0011.0 Mini Lighthead Instruction Manual Surface Mount For Synchronization: Connect BROWN wires of all heads together for synchronization (All heads should be set at the same Flash Pattern) For Simultaneous or Alternating Flash: Apply +VDC WHITE and BROWN wires…

Brand: Cell2

cell2 86-B02310-0001.1 LED BEACON User Manual

February 26, 2023

cell2 86-B02310-0001.1 LED BEACON WIRING OPERATION Flash Pattern Selection While Warning Mode has been activated, momentarily apply WHITE wire to +VDC: Once for next pattern Quick 3 times to FP#1 Simultaneous or Alternating Synchronization Setting Enter SETTING MODE by powering…

Brand: Cell2

cell2 LP26 LED PAD Instructions

February 26, 2023

cell2 LP26 LED PAD WIRING CAUTION: Ensure that the mounting surface is evenly flat; mounting this light head on non-flat surfaces may result in bending and/or water ingress. NOTE: When using an adhesive mount, ensure that the mounting surface is…

Brand: Cell2

cell2 B16 LED Beacon User Manual

February 25, 2023

cell2 B16 LED Beacon User Manual OPERATION RED: To +VDC BLACK: To Chassis Ground (-) FLASH PATTERN SELECTION Open Twist the dome lens counter clockwise , then lift the dome lens to open. Change Momentarily push the red button to…

Brand: Cell2