swim fun 1960 UFO Pool Robot

Important: Never operate the cleaner when there are people in the pool.

Important Precautions

• Please read this manual carefully, and use the cleaner according to the manual.
• We are not held liable for any loss or injury caused by improper use.
• Use the accessories recommended or sold by the manufacturer only.
• This model applies to swimmingpools with a flat floor.
• Please do not allow children to ride on it or play with it as a toy.
• If the power line is damaged, it must be replaced by a certified professional.
• Never power on the cleaner when it is out of the water.
• The power line must be connected to a leakage protected and earthed socket when charging.
• Do not operate the cleaner when there are people in the pool.
• Always clean and wash the filter tray after use.
• Power off the cleaner when maintaining, cleaning or not using it.
• Store the pool robot in a cool, frost-free and ventilated location.
• Keep out of direct sunlight
• Frost will damage the battery.
• The cleaner should be stored in a cool place when charging, and not covered with anything to prevent the damage of internal electrical components caused by overheating.
• Only professionals can disassemble the sealed driving kit of the cleaner.
• Do not operate while pool filter is running.
• Please use the original and authorized power adapter only.
• Do not use or store the cleaner near any heat source.

Important: The cleaner should be charged and discharged every three months if it needs to be stored for a long time to maintain battery life.

Introduction

The robotic pool cleaner UFO is a new type of rechargeable automatic cleaner that will filter the pool water and gets rid of suspended particles without replacing the pool water. It’s totally environmental-friendly.

Specifications

Operation instruction

Precautions

• Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool.
• Install the swing plate and floating handle before use.
• Please ensure that the top cover of the cleaner is tightly assembled to its chassis.
• When fastening the top cover and chassis, please focus more on the installation direction as shown in the below figure: the arrow position near the buckle of top cover should be aligned with the hole position near the buckle of chassis.
• When charging, it is strictly forbidden to face the bottom up to prevent the swing plate from being crushed.
• Power off the cleaner after use.

Grab the floating handle and pull at the rope for lifting it on the water surface, and then grasp its handle to remove it from the pool. Hold the cleaner on the water surface for 10-15 seconds until it empties before removing from the pool.

Note: Do not touch the wall to avoid scratching the wall or damaging the cleaner when putting into the pool or lifting out of the pool.

Quick operation

• Plug in the cleaner using the supplied adapter and charging line to charge the battery.

Note: When charging, it is strictly forbidden to leave the pool robot upside down to prevent the swing plate from being crushed.

• Power off the cleaner before charging.
• Clean the charging port before charging.
• Red charging indicator indicates the battery is charging.
• Green charging indicator indicates charging is finished. A full charge always takes 5-6 hours. The battery is not fully charged until after 5-6 hours even though the charging indicator turns green.

Press the switch to power on the cleaner. and lower the pool robot horizontally to the pool floor. The pool robot will start 20 seconds after you have switched on the power. The cleaner will stop running after completing the working cycle. The floating handle can be hooked by a hook with a telescope pole, and the cleaner is pulled to the edge of the pool.

Power-off operation

A sound signal comes when lifting the pool robot out of the pool. Press the switch to OFF and the cleaner will be shut down. Always clean the filter tray after use. Power-off operation: the buzzer will be alarming when lifting out of the pool. Press the switch to OFF and the cleaner will be sht down. Always clean the filter tray after use.

Functions and adjustment of wheels

There are 4 wheels on the cleaner, of which the left and right wheels are fixed. The front and back wheels can be selectively adjusted according to different conditions so as to adjust the running path of the cleaner.

• Setting wheel angle and running path
• A, B, C are printed on the groove of the wheel limit pile of the bottom. Wheel limit piles will be installed by default on C (left) and A (right).
• As shown in the figure, push the wheel buckle, pull down the wheel components, and remove them. Then reinstall the limit pile into chassis to realize the different running paths
• Three settings for wheels are recommended.

Setting 1

• Default, setting: B-C, for most of pools

Wheel angle
Running path

Setting 2

C-A, when the turning angle is too large

• Wheel angle
• Running path

Setting 3

C-C, when the length and width of the swimming pool are large

Wheel angle
Running path

Setting 4

• B-A, for round pools

Wheel angle
Running path

Note: These are the recommended settings. Different settings may work better for your pool.

Cleaning the filter tray

• Open the cleaner by the clips.
• Take off the filter tray
• Clean the filter tray and chassis
• Reassemble the cleaner
• Clap on the clips

Troubleshooting

Sound signal information

Winter storage

During the winter season when the outside temperatures fall below 10°C UFO Pool Robot should be removed to prevent damage from freezing water. Store it inside in a dry and frost free location. Note that the battery must be charged every 3 months to avoid capacity reduction. Otherwise, the guarantee will be void.

Packing list

Exploded view

Parts

Warranty

The warranty period is according to the national laws regarding consumer purchase. The warranty period applies from the date of purchase on your purchase receipt. The receipt must be presented at service calls during the warranty period. It is therefore important that you save your sales receipt. The manufacturer guarantees safe operation and product liability based on the following specific conditions:

• Installation and use in accordance with the manual’s instructions.
• Use only original spare parts

The warranty does not cover normal wear and tear, scratches, abrasions or cosmetic damage. More specifically, the warranty does not cover damage caused if:

• Improper use or handling, including frost damages
• Fall or shock
• Repairs, alterations or etc. performed by anyone other than Swim & Fun
• Improper storing in extremely high or low temperatures, including frost

In the event of guarantee claims please contact your dealer. When returning a defective product, it must be packed in such a way that it is not damaged during transport. It is your responsibility that the product arrives safely. You must state your name, address, phone number and preferably your e-mail address. If the product are to be returned to you! Always remember to state what is wrong with your product.

Customer service

Swim & Fun A/S – hotline:

• Denmark: +45 7022 6856
• Sweden: +46 771 188819
• swim-fun.com/support
• Danmark: +45 7022 6856
• Sverige: +46 771 188819

Swim & Fun A/S

• Ledreborg Allé 128 K, DK-4000 Roskilde
• info@swim-fun.com
• www.swim-fun.com

© All rights reserved Swim & Fun A/S 2022

Documents / Resources

swim fun 1960 UFO Pool Robot [pdf] User Manual 1960 UFO Pool Robot, 1960, UFO Pool Robot, Pool Robot, Robot

References

• User Manual