ST Series Wireless Remote, Halogen, and LED Golight
Product Information
Specifications:
- Remote Type: Wireless Handheld Remote Control
- Models: 3000ST, 3051ST, 3006ST, 30002ST, 30512ST, 30062ST,
30004ST, 30514ST, 30064ST, 30005ST, 30515ST, 30065ST, 30008ST,
30518ST, 30009ST, 30519ST - Power Supply:
- Halogen Units: Draw 5.5 Amps at 13.8V
- LED Units: Draw 3.7 Amps at 13.8V
Product Usage Instructions:
1. Pairing the Remote to the Light:
To ensure proper functionality, follow these steps to pair the
remote with the light:
- Set the remote for spotlight #1 by depressing any directional
key. - Check if the indicator LED for spotlight #1 is lit. If not,
press the spotlight selector button for five seconds to toggle to
the next setting. - Press and hold the on/off key and the speed selector key on the
remote while reconnecting power to the spotlight. The lamp will
flash three times to confirm successful pairing after three
seconds.
2. Troubleshooting Common Issues:
Issue: Light Not Functioning
Potential Solutions:
- Ensure proper pairing of the remote and the light.
- Verify the power supply meets the required current for the
unit. - If issues persist, contact Customer Service for further
assistance.
Issue: Bulb Not Illuminating
Potential Solutions:
- Check power supply adequacy.
- Verify correct polarity for LED units.
- Inspect bulb for defects or perform a continuity test.
- If necessary, troubleshoot receiver-related issues.
Issue: Rotation Problems
Potential Solutions:
- Identify defective motors for horizontal or vertical movement
issues. - If rotation problems persist, consider receiver malfunction as
a possible cause.
FAQ:
Q: How do I pair the remote with the light?
A: Follow the pairing steps outlined in the user manual to
ensure successful communication between the remote and the
light.
Q: What should I do if my light does not illuminate?
A: Check the power supply, verify polarity for LED units,
inspect the bulb for defects, and troubleshoot potential receiver
issues.
Q: Why is my light experiencing rotation problems?
A: Rotation issues may stem from defective motors controlling
movement or faulty receivers affecting rotation functionality.
Quick Troubleshooting Guide Stryker ST Series
Wireless Remote, Halogen, and LED Golight Customer Service: 800.557.0098
REMOTE TYPE: WIRELESS HANDHELD REMOTE CONTROL (3000ST, 3051ST, 3006ST, 30002ST, 30512ST, 30062ST, 30004ST, 30514ST, 30064ST, 30005ST, 30515ST, 30065ST, 30008ST, 30518ST, 30009ST, 30519ST)
1. My light has NO function. Potential issues:
· Programming Issue (Wireless Remotes Only) · Insufficient Power Supply · Defective Batteries or Defective Wireless Remote · Defective Receiver
Programming Issue- Our new Stryker ST Series will not work out of the box. The remote MUST BE PAIRED TO THE LIGHT before first use. The programming process for the ST Series Handheld Wireless Remote Control (Part# 30300) is different from our previous remotes.
1. Set remote for spotlight #1. Depress any directional key to check. The indicator LED for spotlight #1 only should be lit when you do this. If not, depress the spotlight selector button for five seconds to toggle to the next setting. (You may have to do this twice.)
2. Press and hold the on/off key and the speed selector key on the remote while simultaneously reconnecting power to the spotlight. After three seconds the lamp will flash three times to confirm the pairing process was successful
Insufficient Power Supply- Verify your light is receiving adequate current. Halogen units draw 5.5 Amps at 13.8V / LED units draw 3.7 Amps at 13.8V.
Defective Batteries or Defective Wireless Remote- There is a red LED light in the center of your wireless remote control that should light up every time you depress a button. If there is no red LED light, start by replacing the batteries in your remote control (2- AAA batteries). If this does not resolve the issue, the problem may be the remote control. If available, use a different remote control to test the light. If a different remote is not available, please call our Customer Service Department for assistance.
Defective Receiver- If you have done all of the above and your light still has no function; you may have a defective receiver. Please call our Customer Service Department for further instructions.
2. My light will rotate left/right and up/down, but the bulb will not illuminate. Potential Issues:
· Insufficient Power Supply · Polarity Reversed (LED Only) · Defective Halogen Bulb · Defective Receiver
CONTINUED – REMOTE TYPE: WIRELESS HANDHELD REMOTE CONTROL (3000ST, 3051ST, 3006ST, 30002ST, 30512ST, 30062ST, 30004ST, 30514ST, 30064ST, 30005ST, 30515ST, 30065ST, 30008ST, 30518ST, 30009ST, 30519ST)
Insufficient Power Supply- If the motors are operational, this is a sign that the unit is receiving adequate current, but not enough current to illuminate the bulb. Verify your unit is receiving adequate current. Halogen units draw 5.5 Amps at 13.8V / LED units draw 3.7 Amps at 13.8V.
Polarity Reversed- Our LED units are polarity sensitive (Halogens are not). If your light rotates, but not turn on, verify your power wires are hooked up accordingly (+) to (+).
Defective Halogen Bulb- Is there a break in the filament? If no, remove the bulb and perform a continuity test.
Defective Receiver- When pressing the power button on the remote control, do you hear a “clicking” sound? If so, this means the receiver and the remote control are communicating, and the issue is most likely the bulb. (Please note in rare circumstances, a defective receiver can still produce a clicking sound.) If you do not hear anything when you press the power button, the issue could be the receiver.
3. My light will illuminate, but has rotation issues (no left/right, up/down, or both). Potential issues:
· Defective Motor · Defective Receiver · Defective Remote
Defective Motor- There are two motors in the light; one that controls horizontal movement and one that controls vertical movement. If your light will turn on but will not move L/R or U/D, you may have a defective motor.
Defective Receiver- If your light illuminates but rotates intermittently or not at all, your receiver may be the issue.
Defective Wireless Remote- There is a red LED light in the center of your wireless remote control that should light up every time you depress a button. If it does not illuminate when depressing the left, right, up or down arrow you may have a defective remote. If available, use a different wireless remote control to test the light. If a different remote is not available, please call our Customer Service Department for assistance.
Documents / Resources
 | Stryker ST Series Wireless Remote, Halogen, and LED Golight [pdf] User Guide 3000ST, 3051ST, 3006ST, 30002ST, 30512ST, 30062ST, 30004ST, 30514ST, 30064ST, 30005ST, 30515ST, 30065ST, 30008ST, 30518ST, 30009ST, 30519ST, ST Series Wireless Remote Halogen and LED Golight, ST Series, Wireless Remote Halogen and LED Golight, Remote Halogen and LED Golight, Halogen and LED Golight, LED Golight, Golight |