Home | Lightware Visual Engineering
User Guide for LIGHTWARE models including: WP-HDMI-TPS-RX97, WP-HDMI-TPS-RX97-EU, WP-HDMI-TPS-RX97-UK, WP-HDMI-TPS-RX97-US, WP-HDMI-TPS-RX97-FP-8AT, FP-HDMI-TPS-RX97-GB3, TPS-RX97 Series Twisted Pair Hdbase, TPS-RX97 Series, Twisted Pair Hdbase, Pair Hdbase, Hdbase
File Info : application/pdf, 2 Pages, 2.80MB
DocumentDocumentFront View (WP-HDMI-TPS-RX97-FP-8AT model) 1 23 1 Quick Start Guide WP-HDMI-TPS-RX97-EU; -UK; -US; -FP-8AT FP-HDMI-TPS-RX97-GB3 Important Safety Instructions Please read the supplied safety instruction document before using the product and keep it available for future reference. Introduction WP/FP-HDMI-TPS-RX97 series twisted pair HDBaseTTM extenders provide extension of uncompressed 4K/UHD video with embedded audio (up to eight channel PCM or HBR audio) for long distances over a single CATx cable. Box Contents Rear View (WP-HDMI-TPS-RX97-FP-8AT model) 45 IR IN SIGNAL SWaafertryanatnyd Quick Start HDMI OUT Info Guide Receiver unit Safety and Warranty info, Quick Start Guide Phoenix® Combicon 3-pole connector UNC 6-32 bright zinc plated pan head screws (4x) * * For WP-HDMI-TPS-RX97-FP-8AT model only. Please note that the 48V power adaptor is an optional accessory which can be purchased separately. 67 Power Supply Options TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) and can receive power over the TPS line. The extender can be powered by any of the following ways: 1. Local adaptor 2. Remote power injector 3. Matrix board 48V DC Power adaptor IR IN Power send TPS-PI-1P1 IR IN HDMI OUT SIGNAL Ethernet WP-HDMI-TPS-RX97-US IR OUT TX RX LIVE LINK CATx (TPS) External PIN: 2mm Max:2.5A power supply Power send 8MM8M8M8CCCXXCXXHH--HH--TTHHIOPPTTDDN4SSUPPMMP488V22DDSST-UVIICC----P5IOTOI33BA+IINUNNDDB5UB-PATP---TOOIUSBBPEATB-OUtAR-hBAATDeORrBnAFDOeOROAFtRDIUORNTTHWRDPT1PSD1IHWSTMODHIIUNITMTWPH1I1OIWDTEHIIGT3IHTDA3ALDNAADUNODADIUINNOTATAPT2NPSL2ASOOLIUGNOT2AG2UADUIODIO TPS OUT 312V power on TTPPSSOconnect IN 4 IN 3 TPS IN 3 12V power on TPTPSScINon4nect CATx (TPS) SIGNAL HDMI OUT TyMpaicx-a: l+1: .02.55AA Ethernet WP-HDMI-TPS-RX97-US IR OUT TX RX LIVE LINK HDMI OUT Ethernet WP-HDMI-TPS-RX97-US IR OUT 48V DC IR IN SIGNAL Power TX RX LIVE LINK adaptor Bottom View (WP-HDMI-TPS-RX97-FP-8AT model) 8 96 TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power the WP/FP-HDMI-TPS-RX97 series and vica versa. WP/FP-UMX-TPS-RX97 series contains PoE-compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can be remote powered only by each other. ¢ Warranty void if damage occurs due to the usage of a different power source. 1 Status LEDs SIGNAL The LEDs give feedback about the state of the unit and the video signals. off No video signal transmission. on (green) Video signal transmission is active. LINK off TPS connection failed between the extenders. blinking TPS connection is detected and Low (green) Power Partial Functionality (LPPF) link mode is active. on (green) TPS connection is detected and HDBaseTTM (HDBT) or Long reach (LR) link mode is active. LIVE 2 IR input/output 3 RS-232 connector 4 Ethernet 5 HDMI output 6 DC Input 7 TPS input 8 RS-232 switch 9 TPS mode switch q Tie-down point off blinking (green) Device is not powered. Device is powered and ready to use. 2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the detector, IR OUT for the emitter). 3-pole Phoenix connector for RS-232 serial port. Firmware upgrade can also be performed over this interface. Locking RJ45 connector for Ethernet communication. HDMI output for DVI or HDMI signal. Connect an HDMI cable between the receiver and the display device. Connect the output to the 2-pole Phoenix connector on the bottom of the wall plate. Locking RJ45 connector for HDBaseTTM signal transmission. Connect a twisted pair cable between the transmitter and the receiver. Normal: serial data is passed through the device. Prog: RS-232 pass-through function is disabled, the device is ready for the firmware upgrade (see RS-232 switch modes section for details). LR: Longreach TPS mode; lower resolution (max 1080p), longer distances. Auto: TPS mode is determined automatically. The built-in tie-down points are designed to clamp the HDMI and the CATx cable and ensure stable connection. Please see the enlarged picture below. Connecting Steps Projector HDMI RS-232 Compatible transmitter or matrix output board CATx TPS-PI-1P1 Power injector CATx WP-HDMI-TPS-RX97-US Ethernet HDMI OUT WP-HDMI-TPS-RX97 Power IR LAN Power adaptor IR detector Ethernet CATx HDMI RS-232 IR LAN Power Connect the TPS input port of the receiver to the TPS+PoE port of the TPS-PI-1P1 by a CATx cable. Connect the receiver (or the matrix output board) to the power injector by a CATx cable via the TPS port. Connect the sink (e.g. Projector) to the HDMI output port by HDMI cable. Optionally for RS-232 extension: connect a controller/controlled device (e.g. Projector) to the RS-232 port. Optionally for Infrared extension: Connect the IR emitter to the IR OUT port of the receiver, and/or Connect the IR detector to the IR IN port of the receiver. Optionally connect the receiver to a LAN. Powering on the devices is recommended to do as the final step during the installation. Please check the Power Supply Options section for the details. Further Information q The product brief and further information of this appliance is available at www.lightware.com. See the Downloads section on the on the dedicated product page. Compatible Devices TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90 series. The product is compatible with any HDBaseTTM third party devices. HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. RS-232 Switch Modes RS-232 Switch normal prog Programming TPS port Contact us sales@lightware.com +36 1 255 3800 support@lightware.com +36 1 255 3810 Lightware Visual Engineering PLC. Peterdy 15, Budapest H-1071, Hungary Doc. ver.: 2.2 19210003 Assembly Guide of the Bare Extender and the Front Plate ¢ Always apply ESD-protection during the assembling. Electric discharge may harm the electric parts of the device. ¢ Please unplug all cables from the device before performing the steps described below. The following assembly steps can be applied for the following extender models and front plates: Name Type Description WP-HDMI-TPS-RX97 bare Extender WP-HDMI-TPS-RX97 receiver device WP-HDMI-TPS EU plate Accessory Front plate suitable for Double EU wall box WP-HDMI-TPS UK plate Accessory Front plate suitable for Double UK wall box WP-HDMI-TPS US plate Accessory Front plate suitable for Double US wall box WP-HDMI-TPS FP-8AT plate Accessory Front plate suitable for Legrand 8AT floor box Assembly Steps 1. Place the front plate to the bare extender device like it is shown on the figure below. Place the cutout of the front plate under the HDMI flange screw. 2. Suit the front plate like it shall be lying down the device. Typical Application IR cable Serial cable IR emitter Touch panel HDMI-TPS-TX97 HDMEIt,h3eBriD,ndie4rBtieK1dcits0ri/ueo1pc0ntpi0alooIrntRaeldRS-23De2(vIiEceEFEcora8n0b2eb.se3tarfpe)ermfootrempaonwceereusdeovAeWrGT2P3S lCiAnTk6wiotrhCPAoTE7PIS1N:2F2VTP1mAcmaDbCle Made iRnoHESU, Hungary TPS Long Distance Transmitter Sn: HDMI- TPS-TX97 Max:2.5A TPS OUT (PoE) HDMI Blu-Ray or DVD Player PIN: 2mm 48V DC Power adaptor TyMpaicx-a: l+1: .02.55AA TPS-PI-1P1 Ethernet switch CATx TPS connection CATx up to 170m LAN Power send IR cable Serial cable IR OUT TX RX IR IN SIGNAL LIVE LINK WP-HDMI-TPS-RX97-US Ethernet HDMI OUT IR detector HDMI WP-HDMI-TPS-RX97 LAN HD Projector LAN ETHERNET Laptop Bidirectional Pass-through Data Lines The direction of the video extension is fixed from TX towards RX but the pass-through data SERIAL lines are bidirectional*. It means the RS-232, ETHERNET IR, Ethernet source and sink devices can be TX RX connected either to the TX or to the RX and the INFRA #1 signal is transmitted to the other extender. * In fact IR transmission is uni-directional but INFRA #2 the extender has two IR channels with different directions. RS-232 Third party devices with standard RS-232 port are supported as the extenders work in ,,passthrough" mode. TX and RX provide 3-pole Phoenix connector. The RS-232 options the baud rate and the parity bits are set on the third party devices and it can be anything. The extenders support any kind of serial settings. Please find the RS-232 device type in its user guide; the extenders work as DCE devices. Ethernet The Ethernet port on the RX or on TX can be connected to a LAN hub, switch or router with a LAN cable. The other side behaves as an Ethernet uplink port. The extenders support 10/100 Mbps data transfer rate. The Ethernet port has auto crossover function. It is able to recognize and handle both cable types: patch and cross TP cables. Wiring Guide for RS-232 Data Transmission WP/FP-HDMI-TPS-RX97 series are built with 3-pole Phoenix connector. See the below examples of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data Terminal Equipment) type device: Lightware device and a DCE D-SUB 9 - Phoenix Lightware device and a DTE D-SUB 9 - Phoenix TX RX TX RX 5 1 9 6 2: TX data transmit 3: RX data receive 5: Ground 1 5 6 9 2: TX data receive 3: RX data transmit 5: Ground For more information about the cable wiring see the user's manual of the device or Cable Wiring Guide on our website www.lightware.com/support/guides-and-white-papers. 3. Place and screw the provided two pieces M3x12 PZ flat head black screws into the screw holes shown in the figure below. It requires a PZ1 screwdriver. 4. Turn the device upside down. 5. Place provided four pieces M3 bright zinc plated toothed washers to the screws. After it is done, place and screw four pieces M3 metric nuts onto the built-in screws with a 5,5mm socket wrench key. Find more details about the assembly steps of the extender and the mounting options to the wall plates / floor plates in our Mounting Options and Accessories for WP/FP-HDMI-TPS-97 series Extenders assembly guide on the website www.lightware.com. TPS Link Modes The TPS working mode between the transmitter and the receiver parties is determined by the mode set in them. Both parties influence on the setting which determines the final TPS transmission mode. The following TPS modes are defined: Long reach (LR): Longer CATx cable length, less bandwidth (limited resolution). The LPPF mode is not available in LR TPS link mode. HDBaseTTM (HDBT): more bandwidth (higher resolutions), shorter CATx cable length. If no video present, the units change to LPPF mode automatically. Low Power Partial Functionality (LPPF): Only Ethernet, RS-232 and IR are extended. Toggling between TPS link modes The toggle switch on the extenders can be used to toggle between the LR and Auto TPS modes. If both units have Auto state and there is valid video signal on the transmitter the common mode will be HDBT. If the video signal disappears devices go into LPPF mode. The negotiated TPS working mode Selected LR mode (TX) Auto Selected mode (RX) LR Auto LR LR LR HDBT TPS mode between an extender and a port of a matrix board If an extender and a TPS matrix board are paired the board forces the extender to use the settings of the matrix. The extender's TPS mode switch has no effect. Always use the Auto mode with third-party devices. Dimensions a c 1 b c 2 Receiver and Front plate model WP-HDMI-TPS-RX97-EU WP-HDMI-TPS-RX97-UK WP-HDMI-TPS-RX97-US WP-HDMI-TPS-RX97-FP-8AT FP-HDMI-TPS-RX97-GB3 Dimensions (mm) a bc c 1 2 80 150 24,5 33,4 Recommended outlet box type for mounting European two gang panel Part no.: 77190-D3 80 140 24,5 33,4 Appleby galvanised steel knockout boxes 2g 47mm 114.3 115.9 24,5 33,4 Carlon B225R 104,5 111,5 24,5 33,4 Legrand 8AT 44.8 134.5 24,5 OBO Bettermann: UT4; Part no.: 7408727 33,4 Cover plate: OBO Bettermann UT4 P3; Part no.: 7408 76 1 Legrand 89610 Infrared (IR) One emitter and one detector is enough for remote controlling one IR sink device. If there is an IR sink device to be controlled next to the TX and the other one is next to the RX, two emitter-detector pairs are needed. The IR emitter and the detector have standard 3.5 mm TRS (jack) connectors. The emitter's plug has two poles (mono) and the detector's plug has three poles (stereo). The emitter and detector pair is not supplied with the product, it can be ordered from Lightware separately. Types of IR Connectors (1/8" TS / TRS ) 123 1 2-3 Detector 3-pole-TRS 1 Tip Signal (active low) 2 Ring GND 3 Sleeve +5V Emitter 2-pole-TS 1 Tip +5V 2 Ring 3 Sleeve Signal (active low) Maximum Extension Distances Below values are valid when the receiver is powered by a local adaptor; distances may decrease depending on the powering mode (local or remote) and cable quality. Resolution 1024x768@60Hz 1280x720p@60Hz 1920x1080p@60Hz (24bpp) 1920x1200@60Hz 1600x1200@60Hz 1920x1080@60Hz (36bpp) 3840x2160@30Hz UHD ** 4096x2160@30Hz 4K ** Pixel clock rate Cable lengths (Auto / Long reach TPS mode) CAT5e AWG24 CAT7 AWG26 CAT7 AWG23 65 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m* 73.8 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m* 148.5 MHz 100 m / 130 m* 90 m / 120 m* 120 m / 170 m* 152.9 MHz 100 m / NA 162 MHz 100 m / NA 90 m / NA 90 m / NA 120 m / NA 120 m / NA 222.75 MHz 70 m / NA 70 m / NA 120 m / NA 297 MHz 297 MHz 70 m / NA 70 m / NA 70 m / NA 70 m / NA 100 m / NA 100 m / NA * Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz. CAT7 SFTP AWG23 cable is always recommended. Specifications General Compliance ...................................................................................................CE, UKCA Electrical safety.................................................................................. EN 62368-1:2014 EMC (emission) ............................................................................. IEC/EN 55032:2015 EMC (immunity)............................................................................. IEC/EN 55035:2017 RoHS .....................................................................................................EN 63000:2018 Warranty ............................................................................................................. 3 years Operating temperature ...................................................0° to +50°C (+32° to +122°F) Cooling ................................................................................................. by a cooling fan Weight......................................................................................... approx. 370g (0.82 lb) Power Power supply .......................... external power adaptor / PoE (IEEE 802.3af) via TPS Power adaptor ......................... Input 100-240 V AC 50/60 Hz, Output 48V DC, 0.5 A Power consumption ................................................................... 6.5W (typ) / 8W (max) DC power connector..............................................................2-pole Phoenix connector Connectors RX input ........................................................................................RJ45 (TPS interface) RX output ..............................................................................................HDMI connector Ethernet ................................................................................................................. RJ45 IR input, output ................................................................ 3.5 mm (1.8") jack connector Serial port................................................................................................3-pole Phoenix Digital video signal Supported signals ........................................................................... DVI 1.0, HDMI 1.4 Signal standard ................ DVI and HDMI standard which supports embedded audio Supported resolutions.............. up to 4K / UHD (30Hz RGB 4:4:4, 60Hz YCbCr 4:2:0) ............................................................................................1920x1080@120 Hz, 24 bit 3D support ............................................................................................................... yes HDCP compliant ...................................................................................................... yes Control over CEC ................................................................yes, only over HDMI signal EDID support .............................................................................................. transparent Equalization .................................................................................... adaptive, automatic Ventilation ¢ To ensure the correct ventilation and avoid overheating mount the extender into an industrial standard switch/outlet box. Let enough free space in front of the appliance and keep the ventilation holes free. The picture on the right side shows the direction of the airflow. OUT OUT IN