SETSOMI-logo

HUNTER Klein 19440 Light Pendant

HUNTER-Klein-19440-Light-Pendant-product

holim 'view

HUNTER-Klein-19440-Light-Pendant-fig-1

LIEKETSENG LITLHAKISO

TEMOSO 

  • To avoid possible electrical shock, beforeinstalling your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location
  • Sesebelisoa sa mabone se tlameha ho theoa fatše. Haeba terata ea mobu ea sebaka sa ho kenya e le sieo, emisa hanghang ho emisa 'me u buisane le setsebi sa motlakase se tšoanelehang.
  • Wiring eohle e tlameha ho latela likhoutu tsa motlakase tsa naha le tsa lehae ANSI / NFPA 70. Haeba o sa tloaela wiring kapa o belaela, ikopanye le setsebi sa motlakase se tšoanelehang.

BALA O BOLOKE LITAELO TSENA
Litaelo tsena li fanoe bakeng sa polokeho ea hau. Ho bohlokoa haholo hore li baloe ka hloko le ka botlalo pele li qala ho kenya lisebelisoa tsa mabone.

Lisebelisoa ke tsena tseo u tla li hloka ho phethela ho kenya

HUNTER-Klein-19440-Light-Pendant-fig-3

HO ITOKISETSA HO KENYA

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop  (E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G) to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..

KOPANO MOLIMO

There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of canopy (D), and canopy loop (E). Screw the top rod to canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

HUNTER-Klein-19440-Light-Pendant-fig-2

KOPANTS'ANG MAHAPA 
Hokela lithapo tsa sesebelisoa ho lithapo tsa phepelo ea motlakase tse tsoang lebokoseng la mateano. Hokela batsho ho batsho (Live); e tšoeu ho ea ho e tšoeu (e thehiloeng fatše); ho theolela fatše (botala kapa koporo). Sotha lipheletsong tsa lipara tsa terata hammoho. Ebe, sotha holim'a sehokelo sa terata. Etsa bonnete ba hore li-twist tsohle li ka lehlakoreng le le leng. terata ea fatše ea loop ho pota-pota screwing grounding (C) ebe e tiisa. Haeba ho se na terata ea fatše (e tala kapa ea koporo) ho tloha lebokoseng la mateano, ikopanye le ramotlakase ea nang le tsebo.

QETELLO MOKHATLO

Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Carefully install glass shade (M) over socket (L), then install socket cover (N) and tighten up the glass shade with socket ring (O). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Kemiso ea hau e felile. Bulela motlakase 'me u leke sesebelisoa.

LIEKETSENG LITLHAKU

Tšoara mochini ka bonolo! Ho hloekisa khafetsa ho tla fokotsa tlhoko ea tlhoekiso e tebileng. Bakeng sa ho hloekisa kamehla, tima lebone 'me u hlakole sebaka seo ka lesela le hloekileng le se nang lesela kapa lesela la microfiber. Le ka mohla o se ke oa fafatsa mochini o hloekisang ka kotloloho.

Tsebiso
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod

Tlhahiso ea Hunter Pro 
Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access

Litokomane / Lisebelisoa

HUNTER Klein 19440 Light Pendant [pdf] Buka ea litaelo
Klein 19440, Klein, 19440, Light Pendant

Leave ka tlhaloso

aterese ya hao ya imeile ke ke ho phatlalatswa. masimo hlokahala di tšoauoa *