Buka ea Mosebelisi ea EPEVER PWM-VS1024AU AU ea Solar Charge Controller

Tokomane

PWM-VS1024AU AU Series Solar Charge Controller

BEIJING EPSOLAR TECHNOLOGY CO., LTD.
Thank you for selecting ViewStar AU series solar charge controller. Please read this manual carefully before using the product.
ViewStar AU letoto la selaoli sa tefiso ea letsatsi
1. Ho fetaview
Kea le leboha ka ho khetha faele ea ViewStar AU series common positive solar charge controller. The VS-AU controller is a PWM charge controller with built in LCD display that adopts the most advanced digital technique. The multiple load control modes enable it can be widely used on solar home system, traffic signal, solar street light, solar garden lamp, etc. The features are listed below: Adopt high quality components of ST,IR and Infineon, make sure product using lifespan Terminals have UL and VDE certification, the product is more safer and more reliable Controller can work continuously at full load within the environment temperature range
from -25 to 55 3-Stage intelligent PWM chargingBulk, Boost/Equalize, Float Support 3 charging options: Sealed, Gel, and Flooded LCD display design, dynamically displaying device’s operating data and working
condition Double USB design, the power supply charge for electronic equipment With humanized button settings, operation will be more comfortable and convenient Multiple load control modes Energy statistics function Battery temperature compensation function Extensive Electronic protection
2. Likarolo tsa lihlahisoa

Setšoantšo sa 1 Sebopeho

LCD

Boemelong ba Battery

Konopo ea MENU

Li-terminals tsa mojaro

Boema-kepe ba RTS

Beha Konopo

Li-terminals tsa PV

Likoung tsa Phatlalatso ea USB

USB output ports provide the power supply of 5VDC/2.4A and have the short

circuit protection.

Khetho ea Bohlokoa:

Name: Remote Temperature Sensor

Model: RTS300R47K3.81A

Acquisition of battery temperature for undertaking temperature compensation of control parameters, the standard length of the cable is 3m (length can be customized). The RTS300R47K3.81A connects to the port on the controller.

NOTE: Unplug the RTS, the temperature of battery will be set to a fixed value 25ºC.

3. Ho kenya mohala

Tel+86-10-82894112 / 82894962 Websitewww.epsolarpv.com/www.epever.com
(3)The battery fuse should be installed as close to battery as possible. The suggested distance is within 150mm.
(4) The VS AU series is a positive ground controller. Any positive connection of solar, load or battery can be earth grounded as required.
NOTE: Please connect the inverter or other load that it has the large start current to the battery rather than to the controller, if the inverter or other load is necessary.
4. Ts'ebetso

4.1 Mosebetsi oa Konopo
Button MENU button
SET konopo
Pontšo ea LCD ea 4.2

mosebetsi
Browse interface Setting parameter
Load ON/OFF Clear error Enter into Set Mode Save data

Status Description Item
Sehlopha sa PV
Battery
Load Browse interface

Setšoantšo

Status Day Night No charging Charging PV Voltage, Current ,Power Battery capacity, In Charging Battery voltage. current, temperature Battery type Load ON Load OFF Load Voltage, Hajoale, Mokhoa oa ho kenya

HLOKOMELA
1 When no operation, the interface will be automatic cycle, but the follow two interfaces
not be display.

Figure 2 Connection diagram (1) Connect components to the charge controller in the sequence as shown above and pay much attention to the “+” and “-“. Please don’t insert the fuse or turn on the breaker during the installation. When disconnecting the system, the order will be reserved.
(2)After power on the controller, check the LCD on. Otherwise please refer to chapter 6.Always connect the battery first, in order to allow the controller to recognize the system voltage.
1

2 Accumulative power zero clearing: Under PV power interface, press SET button and hold on 5s then the value blink, press SET button again to clear the value.

3 Setting temperature unit: Under battery temperature interface, press SET button and hold on 5s to switch.

Pontšo ea phoso

boemo

Setšoantšo

Tlhaloso

Leshala le holofalitsoe

Boemo ba betri bo bontša ho se na letho, ho panya ha foreimi ea betri, ho panya ha letšoao la phoso

Battery ho feta voltage

Boemo ba betri bo bonts'a e tletse, foreimi ea betri e panya, letšoao la phoso le panya

2

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

Ho Fetetsa ha Battery

Boemo ba betri bo bonts'a boleng ba hajoale, ho panya ha foreimi ea betri, ho panya ha letšoao la phoso

Ho hloleha ha mojaro

Load overload ,Load short circuit

When load current reaches1.02-1.05 times 1.05-1.25 times, 1.25-1.35 times and
1.35-1.5 times more than nominal value, controller will automatically turn off loads in 50s, 30s,10s and 2s respectively

4.3 Ho seta mokhoa oa ho kenya

Operating Steps: Under load mode setting interface, press SET button and hold on 5s till the number begin flashing, then press MENU button to set the parameter, press SET button to confirm.

Selemo 1

Selemo 2

Leseli ON / TSOANG

Bokooa

Load will be on for 1 hour

Load will be on for 1 hour

since sunset

pele letsatsi le chaba

Load will be on for 2 hours

Load will be on for 2 hours

since sunset

pele letsatsi le chaba

Load will be on for 313

hours since sunset

Load will be on for 313

hours before sunrise

Load will be on for 14 hours since sunset

Mojaro o tla lula lihora tse 14 pele letsatsi le chaba

Load will be on for 15 hours

Load will be on for 15

since sunset

hours before sunrise

Mokhoa oa teko

Bokooa

Manual mode(Default load ON)

Bokooa

NOTE: Please set Light ON/OFF, Test mode and Manual mode via Timer1. Timer2 will be disabled and display “2 n”.

Mofuta oa Battery oa 4.4
Mehato ea Ts'ebetso

Under Battery Voltage interface, press SET button and hold on 5s then enter into the interface of Battery type setting. After choosing the battery type by pressing MENU button, waiting for 5s or pressing SET button again to modify successfully.

Mofuta oa Leshala

Tel+86-10-82894112 / 82894962 Websitewww.epsolarpv.com/www.epever.com

Controller Overheating Load Short Circuit
Mojaro o boima haholo
RTS e senyehileng

Temperature sensor is higher than 85 Temperature sensor is less than 75 Load current 2.5 times rated current One short circuit, the output is OFF 5s Two short circuit, the output is OFF 10s Three short circuit, the output is OFF 15s Four short circuit, the output is OFF 20s Five short circuit, the output is OFF 25s Six short circuit, the output is OFF
Load current 2.5 times rated current 1.02-1.05 times, 50s, 1.05-1.25 times, 30s 1.25-1.35 times,10s 1.35-1.5 times 2s
RTS e khutsufalitsoe kapa e senyehile

Output is OFF Output is ON
Output is OFF Clear the fault: Restart the controller or wait for one night-day cycle (night time>3 hours).
Output is OFF Clear the fault: Restart the controller or wait for one night-day cycle (night time>3 hours). Charging or discharging at 25

6. Ho rarolla mathata

Faults The LCD is off during daytime when sunshine falls on PV modules properly
Wire connection is correct, LCD not display
Ho panya ha sefahleho
Ho panya ha sefahleho
Ho panya ha sefahleho

Mabaka a ka bang teng

PV

drive

hlakola

1) Matla a betritage is lower than 9V 2) PV voltage e ka tlase ho matla a betritage

Battery ho feta voltage
Leshala le holofalitsoe
Ho Fetetsa ha Battery

Ho batle phoso
Netefatsa hore likhokelo tsa PV terata li nepahetse ebile li tiile
1) Please check the voltage of battery. At least 9V voltage to activate the controller 2) Check the PV input voltage which should be higher than battery’s Check if the battery voltage is higher than OVD point (over voltage khaoha voltage), and disconnect the PV. When the battery voltage e khutlisetsoa ho kapa ka holimo ho LVR point (low voltage kopanya hape voltage), the load will recover The controller will automatically turn the system off. But while the temperature decline to be below 50 ºC, the controller will resume.

Sealed (Default)

Gel

Moroallo

NOTE: Please refer to the battery voltage parameters table for the different battery

mofuta.

5. Protections

Ho panya ha sefahleho
8. Taba ea bohlokoa

Over load or Short circuit

Please reduce the number of electric equipments or check carefully loads connection.

Protection
PV Reverse Polarity Battery Reverse Polarity Battery Over Voltage Battery Over Discharge
Ho Fetetsa ha Battery

maemo a
When the battery is correct connecting, the PV can be reversed. When the PV is not connecting, the battery can be reversed.
Voltage reaches to the OVD

boemo
The controller is not damage
Emisa ho tjhaja

Voltage reaches to the LVD
Temperature sensor is higher than 65 Temperature sensor is less than 55

Emisa ho qhala
Output is OFF Output is ON

Tiisetso ena ha e sebetse tlasa maemo a latelang:
1) Damage from improper use or use in an unsuitable environment. 2) PV or load current, voltage or power exceeding the rated value of controller. 3) The controller is working temperature exceed the limit working environment temperature. 4) User disassembly or attempted repair the controller without permission. 5) The controller is damaged due to natural elements such as lighting. 6) The controller is damaged during transportation and shipment.

7. Litlhaloso tsa Technical

Item

Tlhaloso: VS1024AU

Tlhaloso: VS2024AU

Tlhaloso: VS3024AU

Tlhaloso: VS3048AU

Tlhaloso: VS4524AU

Tlhaloso: VS4548AU

Tsamaiso ea lebitso voltage Battery input voltage fapaneng

12 / 24VDC ka boiketsetso
9V32V

12/24/36/48VDC Auto
9V64V

12 / 24VDC ka boiketsetso
9V32V

12/24/36/48VDC Auto
9V64V

Tefiso e lekantsoeng/ea ho ntša chelete [imeile e sirelelitsoe]

[imeile e sirelelitsoe]

[imeile e sirelelitsoe]

[imeile e sirelelitsoe]

Max. PV e bulehileng potoloho voltage

50V

96V

50V

96V

Battery type Equalize Charging Voltage Boost Charging Voltage Float Charging Voltage

Sealed(Default) / Gel / Flooded Sealed:14.6V/ Gel: No/ Flooded:14.8V Sealed:14.4V/ Gel:14.2V/ Flooded:14.6V
Tiisitsoe/Gel/Meroallo:13.8V

Moqolo o tlasetage Hokela hape Moqtage

Tiisitsoe/Gel/Meroallo:12.6V

Moqolo o tlasetage Hakolla Moqtage

Tiisitsoe/Gel/Meroallo:11.1V

Self-consumption Temperature compensation coefficient

9.2mA/12V;11.7mA/24V; 14.5mA/36V;17mA/48V -3mV//2V25

Charge circuit voltage drop Discharge circuit voltage drop LCD temperature range

0.29V 0.16V -20+70

Working environment temperature Relative humidity Enclosure

-25+55(Product can work continuously at full load)
95%, N.C. IP30

Grounding USB output Overall dimension

142x85x41.5mm 160×94.9×49.3mm

Common Positive

5VDC / 2.4A (Kakaretso)

181 × 100.9 × 59.8mm

194 × 118.4 × 63.8mm

Boemo ba ho hloella

130x60mm

148x70mm

172x80mm

185x90mm

Mounting hole size Terminals

4.5mm 4mm2/12AWG 10mm2/8AWG

5mm 16mm2/6AWG

5mm 16mm2/6AWG

Boima bo kahare

0.22kg

0.35kg

0.55kg

0.58kg

0.76kg

0.88kg

Above the parameters are in 12V system at 25, twice in 24Vsystem, triple in 36V system and quadruple in 48V system.

Tlhaloso: VS6024AU

Tlhaloso: VS6048AU

12 / 24VDC

12/24/36/48VDC

Boitsebiso

Boitsebiso

9V32V

9V64V

[imeile e sirelelitsoe]

50V

96V

214 × 128.7 × 72.2mm

205x100mm

5mm 25mm2/4AWG

1.02kg

1.04kg

Liphetoho leha e le life ntle le tsebiso pele! Nomoro ea phetoleloV1.2

3

4

Litokomane / Lisebelisoa

EPEVER PWM-VS1024AU AU Series Solar Charge Controller [pdf] Buka ea Mosebelisi
PWM-VS1024AU AU Series Solar Charge Controller, PWM-VS1024AU, AU Series Solar Charge Controller, Solar Charge Controller, Charge Controller, Controller

Leave ka tlhaloso

aterese ya hao ya imeile ke ke ho phatlalatswa.