DC2383A-B Evaluation Board
Tataiso ea Mohla
Quad 17V, 1.25A Synchronous Step-DownRegulator with Ultralow Quiescent Current
TLHALOSO
Demonstration circuit 2383A-B features the LT ® 3644-2: the wide input and output voltage range, high efficiency and power density, quad 1.25A outputs DC/DC synchronous step-down monolithic regulator. The input voltage range of DC2383A-A is 2.7V to 17V. The default demo board setting of VOUT1, VOUT2, VOUT3, and VOUT4 is 1.2V, 3.3V, 2.5V, and 1.8V at 1.25A maximum DC output current per channel. There are two assembly versions. The DC2383A-B features LTC3644-2 which operates at an internally fixed frequency of 2.25MHz (Typ), while the DC2383A-A features LTC3644 which operates at an internally fixed frequency of 1MHz (Typ). Peak current limit is internally fixed at 2.2A typical per channel. Each channel comes with independent run pin control and power good indicators. Phase shift selection of either 0 degrees or 180 degrees between switch rising edge of channels 1, 2 and channels 3, 4 is also available.
DC2383A-B provides optional onboard 0Ω jumpers to configure the LTC3644-2 as 4-phase dual 2.5A/2.5A outputs or 4-phase triple 2.5A/1.25A/1.25A outputs. Optional 0Ω jumpers connecting VIN1 to VIN2, VIN3, and
VIN4 are available for users to operate selected channels of LTC3644-2 at different input voltages than VIN1.
A user-selectable MODE/SYNC input is provided to allow users to trade off ripple noise for light load efficiency: pulse-skipping mode (PS) or Burst Mode ® operation delivers higher efficiency at light load while forced continuous conduction mode (FCM) is preferred for noise sensitive applications. The MODE/SYNC pin can also be used to synchronize the switching frequency to an external clock or set the phase shift between channels 1, 2, and channels 3, 4. Constant frequency, peak current mode control architecture and integrated internal control loop compensation network, allows very fast transient response to line and load changes while maintaining loop stability.
The LTC3644-2 is available in a thermally enhanced, low-profile 36-lead 5mm x 5mm BGA package. It is recommended to read the LTC3644-2 datasheet and demo board manual prior to using or making any changes to DC2383A-B.
TS'EBETSO TS'OANE
Specifications are at TA = 25°
| PARAMELA | LITABA | mets | TYP | MAX | UNITS |
| Keletso Voltage Range VIN | 2.7 | 17 | V | ||
| Demo Board Default Output Voltages VOUT1, VOUT2, VOUT3, VOUT4 | FSW = 2.25 MHzBurst Mode VIN = 2.7V to 17V (VOUT < VIN) ILOAD = 0A to 1.25A per Channel |
1.176 3.234 2.45 1.764 | 1.2 3.3 2.5 |
1.224 .366 2.55 1.836 |
V |
| Default Switching Frequency | Internally Fixed Switching Frequency | 1.8 | 2.25 | 2.6 | MHz |
| Maximum Continuous Output Current IOUT per Channel IOUT1, IOUT2, IOUT3, IOUT4 | FSW = 2.25MHz VIN = 2.7V to 17V (VOUT < VIN) VOUT = 1.2V, 1.8V, 2.5V, 3.3V | 1.25 | A | ||
| Efficiency at DC | VIN = 5V FSW = 2.25MHz | 125 | % | ||
| VOUT1 = 1.2V at IOUT1 = 1A | 80.6 | ||||
| VOUT2 = 3.3V at IOUT2 = 1A | 88.1 | ||||
| VOUT3 = 2.5V at IOUT3 = 1A | 86.2 | ||||
| VOUT4 = 1.8V at IOUT4 = 1A | 84.7 | ||||
TSELA E QALANG HO QALA
The MODE/SYNC pin can be used to synchronize the internal oscillator clock frequency to the external clock signal. Place JP3 (MODE/PLLIN) at the CLKIN position, apply an external clock signal at the CLKIN test point (E10) to vary the switching frequency within ±50% of the internal programmed frequency.
The MODE/SYNC pin can also be used to set the phase shift between channels 1, 2 and channels 3, 4 while keeping the PHASE pin tied to INTVCC. The phase shift can be set by modulating the duty cycle of an external clock on the MODE/SYNC pin. In this case, the phase shift will be determined by the applied external clock rising and falling edges. The switch rising edge of channels 1, 2 is synced to the rising edge of the external clock and the switch rising edge of channels 3, 4 is synced to the falling edge of the external clock. Crosstalk between channels can be avoided by adjusting the phase shift between channels such that the SW edges do not coincide.
(Option) 4-Phase Dual 2.5A/2.5A Output Current Configuration:
DC2383A-B can be configured as dual 2.5A/2.5A outputs.
Channel 1 and channel 4 are master channels, and channel 2 and channel 3 are slaves.
The following simple modification is required:
- Tie VIN1, VIN2, VIN3, and VIN4 together or tie VIN1 and VIN2, VIN3 and VIN4 together if operating channels 1 and channel 2 at different input voltage than that of channel 3 and channel 4. Make sure SVIN is tied to the highest input supply voltage.
- Tie SW1 and SW2, SW3 and SW4 together. Since SW1 and SW2, SW3 and SW4 are tied together, there is only one inductor needed for each output voltage rail. Calculate and insert the inductors needed for L1 and L4, and remove L2 and L3.
- Tie FB2 and FB3 to INTVCC.
- Float (do not use) PGOOD2 and PGOOD3. Only PGOOD1 and PGOOD4 are active.
- Tie RUN1 and RUN2, RUN3 and RUN4 together. Note: Make sure to float all the unused onboard RUN pin jumpers to avoid accidentally shorting VIN to GND.
- Tie PHASE pin to INTVCC. Refer to the demo board DC2383A-B schematic for more details.
(Option) 4-Phase Triple 2.5A/1.25A/1.25A Output Circuit Configuration:
DC2383A-B can be configured as triple 2.5A/1.25A/1.25A outputs.
Channel 1 is a master channel, channel 2 is a slave. Channel 3 and channel 4 are independent channels.
The following simple modification is required:
- Tie VIN1, VIN2, VIN3, and VIN4 together, or tie VIN1 and VIN2 together, and VIN3 and VIN4 can be at different input voltages than VIN1 and VIN2. Make sure SVIN is tied to the highest input supply voltage.
- Tie SW1 and SW2 together. There is only one inductor needed for this output voltage rail. Calculate and insert the inductor needed for L1 and remove L2.
- Tie FB2 to INTVCC.
- Float (do not use) PGOOD2. Only PGOOD1, PGOOD3, and PGOOD4 are active.
- Tie RUN1 and RUN2 together. Note: Make sure to float all unused onboard RUN pin jumpers to avoid accidentally shorting VING to GND.
- Tie PHASE pin to INTVCC.
- Channel 3 and Channel 4 are left unchanged since these two channels operate as independent channels.
Refer to the demo board DC2383A-B schematic for more details.
TSELA E QALANG HO QALA
 |
 |
TSELA E QALANG HO QALA
Setšoantšo sa 3. Measured Efficiency at VIN = 5V, FSW = 2.25MHz, Burst Mode
VOUT1 = 1.2V, VOUT2 = 3.3V, VOUT3 = 2.5V, VOUT4 = 1.8V
ILOAD = 1.25A per Channel
TA = 25°C, No Heat Sink, No Forced Airflow
Setšoantšo sa 4. Thermal Performance at VIN = 5V, fSW = 2.25MHz
 |
|
| (a) Load Transient Response: VIN = 8V, VOUT = 1.2V | (b) Load Transient Response: VIN = 12V, VOUT = 1.8V |
 |
|
| (c) Load Transient Response: VIN = 12V, VOUT = 2.5V | (d) Load Transient Response: VIN = 12V, VOUT = 3.3V |
Figure 5. Load Transient Responses
Load Transient Response Test Conditions:
FSW = 2.25MHz Typical
VOUT1 = 1.2V, VOUT2 = 3.3V, VOUT3 = 2.5V, VOUT4 = 1.8V
L1 = L4 = 1µH
L2 = L3 = 2.2µH
Load Step = 0.625A to 1.25A at di/dt = 1A/µs
COUT_ceramic = 1×47µF/1206 + 1x10uF/1206 (per Channel)
Feedforward Capacitor: CFF = 68pF (per Channel)
MAHLOMOLA LEROTHA
| Item | QTY | REFERENCE | KAROLO MOTLATSI | MOHLAHLI/KAROLO YA KAROLO |
Required Circuit Components
| 1 | 4 | CFF1, CFF2, CFF3, CFF4 | CAP, 0402 68pF 5% 50V C0G | MURATA, GRM1555C1H680JA01D |
| 2 | 1 | C1 | CAP. 2917 22uF 20% 35V TANT | AVX, TPSE226M035R0125 |
| 3 | 7 | C2, C4, C5, C7, C9, C10, C14 | CAP, 0805 10uF 10% 25V X5R | MURATA, GRM21BR61E106KA73L |
| 4 | 5 | C3, C6, C11, C12, C15 | CAP, 0603 4.7uF 20% 25V X5R | MURATA, GRM188R61E475ME11D |
| 5 | 1 | C16 | CAP, 0603 1uF 10% 25V X7R | MURATA, GRM188R71E105KA12D |
| 6 | 4 | C19, C21, C23, C25 | CAP, 1206 47uF 10% 16V X5R | MURATA, GRM31CR61C476ME44L |
| 7 | 4 | C20, C22, C24, C26 | CAP, 1206 10uF 10% 25V X7R | KEMET, C1206C106K3RACTU |
| 8 | 2 | L1, L4 | IND, 1uH | MURATA, DFE252012F-1R0M |
| 9 | 2 | L2, L3 | IND, 2.2uH | MURATA, DFE252012F-2R2M |
| 10 | 5 | RSET1, RSET2, RSET3, RSET4, R25 | RES, 0402 100K OHM 1% 1/16W | PANASONIC, ERJ2RKF1003X |
| 11 | 9 | R1, R2, R9, R13, R14, R17, R18, R23, R24 | RES, 0402 0 OHM JUMPER | VISHAY, CRCW04020000Z0ED |
| 12 | 4 | R3, R4, R5, R6 | RES, 0402 100k OHMS 1% 1/16W | VISHAY, CRCW0402100KFKED |
| 13 | 1 | R7 | RES, 0402 2.2 OHMS 1% 1/16W | VISHAY, CRCW04022R20FNED |
| 14 | 6 | R8, R10, R11, R12, R15, R16 | RES, 0402 10M OHMS 1% 1/16W | VISHAY, CRCW040210M0FKED |
| 15 | 1 | R19 | RES, 0402 22.1K OHMS 1% 1/16W | VISHAY, CRCW040222K1FKED |
| 16 | 1 | R22 | RES, 0402 31.6K OHM 1% 1/16W | VISHAY, CRCW040231K6FKED |
| 17 | 1 | R28 | RES, 0402 49.9K OHMS 1% 1/16W | VISHAY, CRCW040249K9FKED |
| 18 | 3 | R29, R30, R31 | RES, 0805 0 OHM JUMPER | VISHAY, CRCW08050000Z0EA |
| 19 | 1 | U1 | IC, QUAD 17V, 1.25A SYNCHRONOUS STEP-DOWN REGULATOR | ANALOG DEVICES, LTC3644EY-2 |
Additional Demo Board Circuit Components
| 1 | 0 | C8, C13, C17, C18 | CAP, 0402 OPTION | KHETHO |
| 2 | 0 | C27, C28, C29, C30 | CAP, 1206 OPTION | KHETHO |
| 3 | 0 | R20, R21, R26, R27 | RES, 0402 OPTION | KHETHO |
| 4 | 0 | R32 | RES, 1206 OPTION | KHETHO |
| 5 | 0 | R33, R34, R37, R38, R39 | RES, 0603 OPTION | KHETHO |
| 6 | 0 | R35, R36 | RES, 0805 OPTION | KHETHO |
Hardware: For Demo Board Only
| 1 | 16 | E1, E2, E3, E4, E5, E6, E7, E12, E14, E15, E16, E17, E18, E19, E20, E21 | TURRET | MILL-MAX, 2501-2-00-80-00-00-07-0 |
| 2 | 10 | E8, E9, E10, E11, E13, E22, E23, E24, E25, E26 | TURRET | MILL-MAX, 2308-2-00-80-00-00-07-0 |
| 3 | 5 | JP1, JP2, JP4, JP5, JP6 | HEADER, 3PIN, 2mm | WURTH, ELEKTRONIK, 62000311121 |
| 4 | 1 | JP3 | HEADER, 2X4PINS 2mm | WURTH, ELEKTRONIK, 62000821121 |
| 5 | 4 | JP7, JP8, JP9, JP10 | HEADER, 2PIN, DBL ROW 2mm | WURTH, ELEKTRONIK, 62000421121 |
| 6 | 4 | MH1, MH2, MH3, MH4 | STANDOFF, SNAP ON 12.7mm | WURTH, ELEKTRONIK, 702935000 |
| 7 | 10 | XJP1, XJP2, XJP3, XJP4, XJP5, XJP6, XJP7, XJP8, XJP9, XJP10 | SHUNT, 2mm | WURTH, ELEKTRONIK, 60800213421 |
SETSEKI SEKEMO
SETSEKI SEKEMO
OPTIONAL JUMPERS FOR PARALLELING PHASES FOR DESIRED NUMBER OF OUTPUT VOLTAGE RAILS (SHARING THE SAME VIN1)
| NUMBER OF OUTPUT VOLTAGE RAILS | Paralleling Channel | Master Channel | 0 OHM (Required) | OPT (Do not stuff) | PHASE (JP13) |
| QUAD 1.25A 4 | 1 / 2 / 3 / 4 | R33, R34, R35, R36, R37, R38, R39 | INTVCC | ||
| TRIPLE 2.5A/1.25A/1.25A 3 | 1+2/3/4 | 1 | R33, R35, R37 | R4, R9, R10, R17, RSET2, CFF2, R19, R34, R36, R38, R39, L2, JP2 | INTVCC |
| DUAL 2.5A/2.5A 2 | 1+2/3+4 | 1, 4 | R33, R34, R35, R36, R37, R38 | R4, R5, R9, R10, R13, R15, R17, R18, RSET2, RSET3, CFF2, CFF3, R19, R22, R39 L2, L3, JP2, JP5 | INTVCC |
HLOKOMELA:
Please refer to the datasheet and demo board manual for more details and examples of paralleling phases to obtain the desired number of output voltage rails.
TSEBISO MOTSEKI
ANALOG DEVISES INC. HAS MADE THE BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER’S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT NALOG DEVICES INC. APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES INC. AND SUPPLIED FOR USE WITH ANALOG DEVICES INC. PARTS.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements f patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any atent or patent rights of Analog Devices.
Tlhokomeliso ea ESD
ESD (electrostatic discharge) sesebelisoa sa bohlokoa. Lisebelisoa tse lefshoang le liboto tsa potoloho li ka tsoa ntle le ho lemoha. Leha sehlahisoa sena se na le li-circuits tse sirelelitsoeng ka molao kapa tsa ts'ireletso, ts'enyehelo e ka hlaha lisebelisoa tse tlas'a ESD ea matla a phahameng. Ka hona, mehato e nepahetseng ea ESD e lokela ho nkuoa ho qoba ho senyeha ha ts'ebetso kapa tahlehelo ea ts'ebetso.
Melao le Maemo a Molao
Ka ho sebelisa boto ea tlhahlobo eo ho buisanoang ka eona mona (hammoho le lisebelisoa life kapa life, litokomane tsa likarolo kapa lisebelisoa tsa ts'ehetso, "Boto ea Tlhahlobo"), o lumela ho tlamahanngoa le lipehelo le lipehelo tse boletsoeng ka tlase ("Tumellano") ntle le haeba o rekile Boto ea Tlhahlobo, moo Melao le Maemo a Thekiso a Thekiso ea Analog a tla laola. Se sebelise Boto ea Tlhahlobo ho fihlela u balile 'me u lumellane le Tumellano. Tšebeliso ea hau ea Boto ea Tlhahlobo e tla bontša ho amohela Tumellano ea hau. Tumellano ena e entsoe ke uena le lipakeng tsa hau ("Customer") le Analog Devices, Inc. ("ADI"), e nang le sebaka sa eona sa mantlha sa khoebo ho One Technology Way, Norwood, MA 02062, USA. Ho ipapisitsoe le lipehelo le lipehelo tsa Tumellano, ADI ka hona e fa Moreki laesense ea mahala, e lekanyelitsoeng, ea botho, ea nakoana, e sa khetheheng, e ke keng ea fetisetsoa, le e ke keng ea fetisetsoa ho sebelisa Boto ea Tlhahlobo BAKENG SA TŠEBELETSO FEELA. Moreki o utloisisa le ho lumela hore Boto ea Tekolo e fanoe ka sepheo se le seng le se ikhethileng se boletsoeng ka holimo, 'me e lumela ho se sebelise Boto ea Litlhahlobo molemong ofe kapa ofe. Ho feta moo, laesense e fanoeng e etsoa ka mokhoa o hlakileng ho ipapisitse le meeli e latelang: Moreki ha aa lokela ho (i) hira, ho hirisa, ho hlahisa, ho rekisa, ho fetisa, ho abela, ho fana ka lengolo la tumello, kapa ho aba Boto ea Tlhahlobo; le (ii) ho dumella Mokga ofe kapa ofe wa Boraro ho fihlella Boto ya Tlhatlhobo. Joalo ka ha le sebelisitsoe mona, lentsoe "Mokha oa Boraro" le kenyelletsa mokhatlo ofe kapa ofe ntle le ADI, Moreki, basebetsi ba bona, basebetsi le baeletsi ba ka tlung. Boto ea Tlhahlobo HA E rekisetsoe Moreki; litokelo tsohle tse sa fanoang ka ho hlaka mona, ho kenyeletsoa beng ba Boto ea Tlhahlobo, li bolokiloe ke ADI. TIISETSO TIISETSO. Tumellano ena le Boto ea Tlhahlobo kaofela li tla nkoa e le litaba tsa lekunutu le tsa botho tsa ADI. Moreki a ka se senole kapa a fetisetsa karolo efe kapa efe ya Boto ya Tekolo ho motho ofe kapa ofe ka lebaka lefe kapa lefe. Ha e khaotsa ho sebelisa Boto ea Tlhahlobo kapa Tumellano ena e felisitsoe, Moreki o lumela ho khutlisetsa Boto ea Tlhahlobo ho ADI hang-hang. KEKELETSO LITHIBELO. Bareki ha baa lokela ho qhaqholla, ho qhaqholla kapa ho khutlisa lichipisi tsa boenjineri ho Boto ea Tekolo. Moreki o tla tsebisa ADI ka tšenyo leha e le efe e etsahetseng kapa liphetoho leha e le life kapa liphetoho tseo a li etsang ho Boto ea Tlhahlobo, ho kenyeletsoa empa e sa felle feela ka ho rekisa kapa ho etsa ntho leha e le efe e amang litaba tsa Boto ea Tlhahlobo. Litokiso ho Boto ea Litlhahlobo li tlameha ho ikamahanya le molao o sebetsang, ho kenyeletsoa empa eseng feela ho RoHS Directive. PUSELETSO NTHAKO. ADI e ka felisa Tumellano ena ka nako efe kapa efe ha e fana ka tsebiso e ngotsoeng ho Moreki. Moreki o lumela ho khutlela ho ADI the Evaluation Board ka nako eo. Tekanyetso ea melato. LEBOTO LA HO HLAHLOBA LE FUMANETSOENG MONA KATLASI LE FUMANA “JOALOKAHA LE TENG” MME ADI HA E ETSE LITIISETSO KAPA EMALI A MOFUTA OFE KA TENG KA TLOPO HO LONA. ADI E HLOKOMELA LITEMELETSO life kapa life, litumellano, TIISETSO, KAPA LITIISETSO, TSE BONANG KAPA TSE HLAHANG KAPA TSE HLAHANG, TSE AMANG LE LEBOTO LA TLHOKOMELISO, EMPA HA LI TLALETSOE, TIISETSO E FUMANEHILENG EA TLHOKOMELISO, TLHOKOMELISO, TLHOKOMELISO, TLHOKOMELISO, TLHOKOMELISO. . IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. MOLATO OA KAOFELA OA ADI HO TSOA MANG KAPA MANG LE LIBAKA TSOHLE E TLA LEKELISOA HO BOLELLO EA LIKERERA TSE LE LEKOKA ($100.00). THEKISO. The customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. MOLAO O BUSANG. Tumellano ena e tla laoloa le ho hlalosoa ho ea ka melao ea motheo ea Commonwealth ea Massachusetts (ho sa kenyelelitsoe likhohlano tsa melao ea molao). Mehato efe kapa efe ea molao mabapi le Tumellano ena e tla mameloa seterekeng kapa makhotleng a mmuso a nang le matla a ho laela Suffolk County, Massachusetts, 'me Moreki o ipeha tlas'a bolaoli le sebaka sa makhotla a joalo.
01 / 22
www.analog.com
©ANALOG DEVICES, INC. 2022
Litokomane / Lisebelisoa
 |
ANALOG DEVICES DC2383A-B Evaluation Board [pdf] Buka ea Mosebelisi DC2383A-B, Evaluation Board, DC2383A-B Evaluation Board, Board, Motherboard |
Lipontšo tse tsoakiloeng le tsa dijithale tse sebetsanang le li-IC | Lisebelisoa tsa Analog
