Instruction Manual for elero models including: M-868 DC, M-868, DC, M-868 DC Radio Tubular Motor, Radio Tubular Motor, Tubular Motor, Radio Motor, Motor
Elero RolSolar M-868 DC Manual - EasyGates Manuals
See 13 207.0001 instructions for the elero Solar-Bundle DC. 3. Programming a suitable elero radio transmitter (see Acces- sories) on the drive (radio ...
File Info : application/pdf, 4 Pages, 649.31KB
DocumentDocument1 2 3 4 5 6 RolSolar M-868 DC assembAly instructions General · Application: Drive system for roller shutters and textile sun protection independent of the mains current, operation with solar energy, pre-charged ready for operation · · PNoowweirrinsguptpolyth: eDimreacitnscuorrretoBnta(1c2onVt)rofrl oumnitbnaettceerysspaarcyk · Limit switch: electronic with soft brake · Noiseless soft brake · Special feature: Cut-out when obstacles are detected, frost protection function, 2 intermediate positions freely definable · End positions adjustable via elero hand-held transmitter (see ,,Accessories") · Wave frequency: from 50 mm Ø Standard scope of deliveryC · MiniPlug Solar DC 0.27 m connection cable (233956301) for Solar Bundle DC plug-in, assembly instructions (138250001) Accessories · Adapter sets, motor bearings, solar bundle DC · elero radio transmitter: MonoTec-868 (28 650.0002) QuinTec-868 (28 655.0002) MonoCom (28 405.0002) D VarioCom (28 445.0002) App Centero Home (version after 1.4.5) Safety instructions &$87,21 General safety instructions for use including installation of motors for roller shutters, awnings, textile sun protection and Venetian blinds can be foundEin the ,,Safety instructions" leaflet supplied with each motor. Please read the general safety instructions and this installation manual carefully as the pro- cedure in this manual is a prerequisite for correct use of the product. Any intervention by unqualified personnel or failure to comply with warnings may lead to personal injuries or materi- al damage. All work on the device may only be carried out by a qualified and approved electrician. RelFevant national regulations must be observed. Figures included are for illustration purposes only. The illus- trations may are provided differ from your product for general information owniltyh1. in minor details an2d elero GmbH continuously strives to improve all products. As a result, the specifications, features and technology of this prod- uct may be changed at any time. The information provided is based on current information at the time of publication. No claims can be derived from the technical data, images and information provided in this manual. Assembly · Only connect the drive with the power turned off. · Only operate the drive in a horizontal position for its intend- ed use. · The length of the winding shaft is determined for each specific installation depending on the drive head and motor bearing used at the installation site. Installation in profile tube / round tube · Push the drive with mechanical seal ring on the motor head and the appropriate adapter set (drive adapter and crown adaptor, accessories) in the profile tube. · Secure the counterpart support to prevent axial movement (screw or rivet on the idler). · Secure the drive axially in the support. · Attach the blind to the shaft. Do not drill holes near the drive area. Connecting cable pluggable 0,27 m Connection from the drive to the power supply (battery pack and solar panel or mains/charger device) with cable flag and DC note. Additional adapters Y-cable Type A or Type B available to expand the system (see Solar-Bundle DC). Mini Plug for the drive Drive adapter for solar panel Connector for power supply (battery pack / mains/charger dCeovimce)missioning in 5 steps Commissioning takes place in this order: 1. Installation of the drive in the system (profile or round tube). 2. Wiring first with solar panel and then with battery pack. Caution: When the plug connections are made, the drive is live and ready for use. See 13 207.0001 instructions for the elero Solar-Bundle DC. 3. Programming a suitable elero radio transmitter (see Accessories) on the drive (radio receiver) and assigning the running directions. Step 3.a) or 3.b). 4. Deleting the end positions (not necessary for initial commissioning) and setting the end positions up and down. 5. Optional: Define additional blind positions. Step 3: Program radio transmitter 3.a) Asynchronous programming mode (standard) Asynchronous programming mode is suitable for programming Gratfrei · Of the first radio transmitter burr-free Diese Maße werden be This dimensions are pa Lieferantenkennzeichnu Supplier ID according t · Of an additional radio transmitter Gemäß RoHS-Richtlinie 2011/65 EG / according to RoHS d -- - - · Of individual radio receivers if several radio recei-ve-rs -are - ready to be programmed -- - - -- - - Operating procedure Result -- -- - - 1 Activate asynchronous programming standby: -- - - -- - - -- - - Connect battery pack to Rol- The radio receiverIndcexh: Raeg.nNrgKuerzbseschtroeibung / Short Comment: Da Solar M-8368 DC again or on 4 asynchronous progra5 mming 6 an already programmed radio standby for 5 minutes. Ready transmitter, press buttons to receive the programming [UP ] + [DOWN ] + [P] button [P]. simultaneously for 3 seconds. 2 Start programming mode: On the radio transmitter to be The radio receiver changes to programmed (in the required asynchronous programming channel), press and hold the mode and starts cyclical up programming button for approx. and down travel (a 2-second 1 second [ P ] (prerequisite: time delay is possible). voltage interruption within the last 5 minutes). 3 Setting the first hit: Hit successful: Immediately after motion com- Radio receiver briefly inter- mences, press the [OPEN ] rupts ongoing travel. or [DOWN ] button. Hit failed: · In case of upward motion, Radio receiver does not inter- press the [UP ] button. rupt ongoing travel. · In case of downward motion, Repeat ,,Set first hit" action! press the [DOWN ] button. 4 Set second hit: Hit successful: Prerequisite: Radio receiver stops ongoing First hit has been set. travel and signals completion Immediately after motion in the of programming. opposite direction commenc- Hit failed: es, press the [OPEN ] or Radio receiver does not stop [DOWN ] button. ongoing travel. · In case of upward motion, Repeat ,,Set second hit" press the [UP ] button. action! · In case of downward motion, press the [DOWN ] button. 138250001_EN_0321 RolSolar M-868 DC assembly instructions 3.b) Synchronous programming mode Synchronous programming mode is suitable for · Programming an additional radio transmitter. · Simultaneously programming several radio receivers to one radio transmitter or channel. Operating procedure Result 1 Activate synchronous programming standby: Press the buttons [DOWN ]+[P] simultaneously on a radio trans- mitter that is already programmed and hold them down for at least 3 seconds. The radio receiver changes to synchronous programming standby for 5 minutes. Ready to receive the programming button [P]. 2 Start programming mode: On the radio transmitter to be pro- The radio receiver changes grammed (in the required channel), to synchronous program- press and hold the [P] programming ming mode and starts cycli- button for approx. 1 second. cal up and down travel. 3 Setting the first hit: Hit successful: Immediately after motion com- Radio receiver briefly inter- mences, press the [OPEN ] or rupts ongoing travel. [DOWN ] button. Hit failed: · In case of upward motion, press Radio receiver does not the [UP ] button. interrupt ongoing travel. · In case of downward motion, Repeat ,,Set first hit" press the [DOWN ] button. action! 4 Set second hit: Hit successful: Prerequisite: Radio receiver stops ongo- First hit has been set. ing travel and signals com- Immediately after motion in the pletion of programming. opposite direction commences, Hit failed: press the [OPEN ] or [DOWN ] Radio receiver does not button. stop ongoing travel. · In case of upward motion, press Repeat ,,Set second hit" the [UP ] button. action. · In case of downward motion, press the [DOWN ] button. The following applies to both programming modes: · Programming can only ever be performed in one selected channel. · When programming is complete or after 5 minutes have passed, the radio receiver will revert to normal operation. · Programming mode can be stopped by pressing the [STOP ] button for at least 6 seconds. · Several radio receivers can be programmed to one channel. · If the blind moves in the wrong direction, delete the radio transmitter and program it again. Delete the radio transmitter To delete the radio connection between the radio transmitter and radio receiver, there are 2 operating procedures available, each of which trigger a specific action in the radio transmitter and radio receiver. Operating procedure Result Simultaneously press the [STOP]+[P] buttons for at least 6 seconds until the status LED lights up red and goes out. In the radio transmitter: The selected channels are deleted entirely. In the radio receiver: The individual radio transmitter only is deleted from the radio receiver. Simultaneously press the [UP ] + [DOWN ] + [STOP ] + [P] buttons for at least 6 seconds until the status LED lights up red and goes out. In the radio transmitter: The selected channels are deleted entirely. In the radio receiver: All radio transmitters are deleted from the radio receiver. For details, see also the elero operating instructions for the radio transmitter used. Step 4: Deleting and setting the end positions Requirements for setting the end positions : 1. Radio transmitter has been taught into the radio receiver. 2. The blind is in a middle position. 3. Establish readiness for end position setting: Simultaneously press buttons [UP ] + [DOWN ] + [P] for at least 6 seconds. The drive remains in programming mode for 5 minutes. The end positions can only be reset if the previous end position settings have been deleted (not applicable for initial commissioning the radio receiver/drive). It is not possible to correct a single end position as both end positions must always be set up. Types of end position settings Different combinations of end position settings are possible. These can be clearly selected according to the technical requirements of the blind. End position settings possible with End position freely adjustable T-strap, belts, tape Fixed upper stop (can be switched off to torque or with release) End stopper, angle bar Fixed lower stop (can be switched off to torque or with release) Anti push-up device, rigid shaft connectors Deletion of end positions Operating procedure Result Starting from a central position of the blind, simultaneously press the [UP ] + [DOWN ] buttons with a programmed radio transmitter until the drive briefly travels up and down. The adjusted end positions have been deleted. The end positions may be readjusted. It is not possible to delete a single end position as both end positions are always deleted. Setting the end positions Operating procedure Result Set upper end position: Press the [ ON ] button until the blind has reached the required upper end position * or stops at the upper stop. * You can make corrections using the [UP ] and [DOWN ] buttons. Press the [DOWN ] button until the drive stops automatically. The drive begins to travel, briefly stops and travels further (for as long as the [UP ] button remains pressed). The upper end position has been set. Set lower end position: Press the [DOWN ] button until the blind has reached the required lower end position * or stops at the lower stop. * You can make corrections using the [UP ] and [DOWN ] buttons. Press the [UP ] button until the drive stops automatically. The drive begins to travel, briefly stops and travels further (for as long as the [DOWN ] button remains pressed). The lower end position has been set. Adjustment of the end positions is complete. - 2 - RolSolar M-868 DC assembly instructions Step 5: Further blind positions Intermediate position: Place blind in any position between the upper and lower end positions Define in the receiver Approach Delete Prerequisite: The blind is in the upper end position. 1. Press the [DOWN ] button until the required intermediate position is reached. 2. Then press the [STOP ] button for 1 second. The blind will stop. The status LED lights up briefly. The intermediate position is now stored. Double click the [DOWN ] button (in quick succession): Blind moves to the saved intermediate position. If no intermediate position has been defined, the blind moves to the lower end position. Simultaneously press and hold the [DOWN ] + [STOP ] buttons for approx. 3 seconds. The intermediate position is now deleted. The status LED lights up briefly. Ventilation position: E.g. the ventilation gaps on the roller shutter open Define in the receiver Approach Delete Requirement: Blind is in the lower end position. 1. Press the [UP ] but- ton until the ventilation gaps open. 2. Then press and hold the [STOP ] button for 1 second. The blind will stop. The position of the ventilation is now saved. Double click the [UP ] button: The blind travels to the saved position. If no ventilation position is defined, the blind moves to the upper end position. Simultaneously press and hold the [UP ] + [STOP ] buttons for approx. 3 seconds. The position of the ventilation is now deleted. Problem Radio programming mode does not start Radio transmitter not in programming mode Drive stops after a short travel time and/or no longer responds End positions cannot be taught in to the drive Possible cause · Faulty connection · Time frame al- ready expired (5 min.) · Battery in radio transmitter is used up · The [UP ] or [DOWN ] button was pressed too late · Battery pack capacity is too low / battery low · Blind difficult to move · End position is not saved · Travel to end position / limit stop too short Remedial action · Check connection · Activate programming standby or briefly interrupt the power supply for programming via a radio transmitter that has already been programmed · Check the radio transmitter (LED must be illuminated) · Start radio programming mode again and observe the time window (1 second) · Charge the battery pack with the mains/charger device (accessory) or replace with a new one · Check the smooth running of the blind · Reset the end position · Bring the blind to the middle position, delete the end positions and reset them Manufacturer's address elero GmbH 73278 Schlierbach GERMANY www.elero.com Service If malfunctions occur or the device is damaged despite correct handling, contact your contractor or dealer. EU Conformity elero hereby declares that this product is in compliance with the essential requirements and other relevant provisions of European directives that are applicable in Europe. A declaration of conformity is available at the website www.elero.com/downloads-service. Disposal / Notes on environmental protection Electrical and electronic devices may not be disposed of with household waste. The consumer is legally obligated to return electrical and electronic equipment as well as batteries/battery packs to the designated public collection points or to the retailer at the end of their service life. The applicable regulations are governed by the relevant local laws. The symbol on the product, the instruction manual or the package indicates the applicable regulations. After using the unit for the final time, protect the battery pack against short circuits. By recycling or reusing old units/batteries, you are making an important contribution to protecting our environment. - 3 - E 33 RolSolar M-868 DC assembly instructions C D Technical data and dimensions 55 O 45 The technical data specified is subject to tolerance factors (according to applicable standards) and refer to an ambient temperature of 20 °C. RolSolar E Rated voltage [V] Rated torque [Nm] C M10 -868 DC D12 (DC) 10 M20 -868 DC 12 (DC) 20 M1,5/90 -868 DC RH 12 (DC3)3 1,5 M3/60 -868 DC RH 12 (DC) 3 Rated speed (rpm) 16 16 90 60 55 O 45 Rated current [A] 4.0 6.0 4,0 4,2 Rated power consumption [W] 48 C 72 48 50 Radio frequency band [MHz] E Radio transmission power [dBm] D max10 868,0 to 868,6 | 869,4 to 869,65 max10 max 1033 max 10 29 Shaft diameter [mm] 50 50 50 50 O 49,5 O 45 Protection class (IP) 44 44 44 44 Limit switch range (revolutions) 40 40 40 40 Operating time (min S2) 10 C 10 10 10 E Length C [mm] Length D [mm] Length E [mm] elero head, round head, star head Weight [kg] 44D6 429C D14 | 12 | 19 1.7C0 471 454 14 | 12 | 19 2.20 446 429 33 - | 12 | 1,00 471 454 - | 12 | 1,60 O 45 O 45O 45 Ambient operating temperature [°C] Protection class III E Item number (elero head, RH round E head, SH star head) D-20 to 60 -20 to 60 34 220.0001 34 230.0001 38 220.0001 38 230.0001 39 220.0001 39 230.0001 -20 to 60 33 38 3603.03001 -20 to 60 38 370.0001 O 49,5 55 55 E C 33 DC 29 D 55O 49,5 O 45O 45 C D E 33 O 57,5 O 45 E 33 C D E C 33 D 29 O 49,5 O 49,5 O 45 O 45 E E E elero GmbH Antriebstechnik OO4455 O 45 C D CC DD Maybachstr. 30 73278 Schlierbach, Germany 33 33 OO459,7,55 O 57,5 33 - 4 - info@elero.de www.elero.com We reserve the right to make technical changes