User Manual for IYUNXI models including: FS6601-4, FS8811, FS6601-4 Ceiling Fan With Light, FS6601-4, Ceiling Fan With Light, Fan With Light, Light
Aug 22, 2024 — This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan. ⚠WARNING. Before assembling your ...
Make wiring connections from the house to the LED light directly (don't connect the remote and the fan) to determine it's the issue of the LED light or not.
Ceiling Fan With Light User Manual FS8811 CAUTION INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION SAFETY RULES 1. To reduce the risk of electric shock, turn off the electricity to the fan at the main fuse box or circuit panel before beginning. 2. All wiring must be in accordance with the local electrical codes or National Electrical Code. Electrical installation should be performed by a qualified licensed electrician. 3. To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 4. Make sure the installation site you choose allows clear space for the blades to rotate and at Ieast7feet(2.13 meters) of clearance between the floor and the fan blade tips. 5. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount fan only to an outlet box marked acceptable for fan support and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. 6. The outlet box and ceiling support structure must be securely mounted and capable of supporting at Ieast45 KGS. 7. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. 9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box. 10. Electrical diagrams are for reference only. 11. The fan is more suitable for indoor use. TOOLS REQUIRED This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan. Materials WARNING Before assembling your ceiling fan, refer to secon on proper method of wiring your fan . If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician. Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor(2-wire with ground) of the following size: Installed Wire Length Up to 50 ft Wire Size A.W.G 14 50-100 ft 12 NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing contact your local retailer. Package Includes Check to see that you have received the following parts: Wood Screw Expansion Screws Mounting Bracket Receiver Remote control SETUP 13 5 24 6 Remote Holder Clevis Pin Fan blade screws Blade Washer Canopy Canopy Screws Magnets Decorative cover DownrodHangerBall Bottom Canopy Hairpin Motor&LightKit Fan blades Light source iron disk Light lampshade Unpack the product carefully and check that it is complete and intact. It should not be used if there is any damage to the cable, glass or electrical parts. In such a case, contact customer service immediately. INSTALL THE FAN Tools Required: Phillips Screwdriver, Pair of Pliers, Straight slot screwdriver, Adjustable Wrench, Step Ladder and Wire Cutters. INSTALL THE MOUNTING BRACKET To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7 feet(2.13 meters) from the floor. If there isn't an existing CUL listed mounting box, then read the following instructions: 1. For the concrete ceiling: Mark the location for the ceiling fan first, then drill two holes in the ceiling to aid in securing the ceiling bracket with two expansion screws provided, and secure the mounting bracket to the building structure with two expansion screws provided, tighten the screws. (Fig.l) 2. For the Wood Ceiling: Mark the location for the ceiling fan first, secure the mounting bracket to the building structure with four wood screws provided. (Fig.2) 3. Refer to Fig. 3 for mounting when the ceiling is angled max. 15 degree angle. NOTE: Hanger after the installation must be able to withstand the weight of 45 KGS or more Fig- How to Assemble Your Ceiling Fan 1. Loosen the Metal Plate and LED light Plate with a screwdriver. 2.Fix the fan blades to the motor hole with screws WARNING Failure to install the fan blades firmly may cause damage and injury. 3.Refasten the light source disk with screws and link the light source terminals INSTALL THE DOWNROD REMEMBER to turn off the power. Follow the steps below to hang your fan properly: 1. Remove the lock pin and hitch pin from down rod. 2. Place down rod assembly into canopy and coupling cover, carefully feed motor wires through the down rod assembly. 3. Loosen the two set screws in down rod coupling. 4. Insert down rod into down rod coupling. Install coupling lock Pin through coupling and down rod. Insert hitch pin into the lock Pin until it snaps into place. Tighten set screws incoupling. Slide coupling cover over the down rod coupling. CHANGE DOWNROD (OPT) Ceiling Fan comes with one 4 inches standard down rod which is pre-assembled and attached to the hanger ball, one longer 8 inches down rod is also included for higher ceilings. If you need a different down rod length, please follow these steps: 1. Loosen the hanger ball from down rod by removing the set screw. 2. Slide down rod ball off of down rod and remove the pin. 3. Re-install pin into extended down rod, and slide down rod ball up to the top of the down rod. 4. Re-install set screw to secure ball to down rod. SECURE THE CANOPY Raise the canopy up and align the keyholes on the bottom of the canopy with the 2 screws on the bottom of the mounting bracket. Rotate the canopy until both screws from the mounting bracket drop into the slot recesses. Tighten screws securely. (2.4G) dimming and color mixing fan controller \ Before: 1. Install the Remote OR Wall Switch, DO NOT install both of them. 2. Check circuit fuses or breakers and make sure the battery is installed correctly. 3. Check line wire connections to the fan and switch wire connections in the switch 4. Twist the lampshade counterclockwise into the disc and fix it to complete the installation housing. 5. CAUTION: Make sure the main power is off. Hump Side Slot Problem: Light does not work 1. Check to see that the wire connections in theswitch housing are connected. 2. Make wiring connections from the house to the LED light directly (don't connect the remote and the fan) to determine it's the issue of the LED light or not. L Problem: Fan will not start. White Black 1. Check line wire connections to the fan and switch wire connections in the switch N housing. CAUTION: Make sure the main power is off. 2. Make the Fan wiring connections Without the Remote & transmitter and the light, to determine it's the issue of the fan body or not. SUPPLY INPUT 110VAC a) Please don't wire the light at the bottom b) Connect the Ceiling Fan Neutral Wire (White) to the Neutral Wire (White) coming through the ceiling Connect the Ceiling Fan Live Wire (Black) to the Live wire (Black or Colored) coming through the ceiling Then turn on the main power, check the fan works separately or not. Link the lamp body and the driver to the plug-in wire according to the corresponding Color Live Neutral at Link Drive to Power Wire (Attached Wiring Diagram) 4 Maintenance 1. Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning use only a so brush or lint free cloth to avoid scratching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish. CAUTION Do not use water to cleaning your ceiling fan. It could damage the motor or the finish and create the possibility of electrical shock. Warranty Dear Customer: We warrants that this product is free from defects in materials and workmanship for a period of 1 year from the day of purchase. If the product has been misused, damaged by accident or in any other way of improper use, this warranty becomes void.WPS 文字