iPRO LOGOKutia e përshtatësit
Udhëzim Manual
iPRO WVQJB500 W Adapter BoxNr Model
WV-QJB500-W
WV-QJB500-S
WV-QJB500-G

Paraprake

  • Mos e përdorni këtë kllapa, përveç me kamera të përshtatshme.
    Mosrespektimi i kësaj mund të shkaktojë një rënie që rezulton në lëndime ose aksidente.
  • Referojuni tregtarit punën e instalimit.
    Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
    Sigurohuni që të konsultoheni me shitësin.
  • Instaloni produktin në mënyrë të sigurt në një mur ose një tavan në përputhje me udhëzimet e instalimit.
    Mosrespektimi i kësaj mund të shkaktojë lëndime ose aksidente.
  • Mos i fërkoni skajet e pjesëve metalike me dorën tuaj.
    Mosrespektimi i kësaj mund të shkaktojë lëndime.

Kur përdorni këtë produkt, lexoni gjithashtu "Masat paraprake" të përshkruara në udhëzimet e përdorimit për kamerën që duhet bashkangjitur. 

Parathënie
Use this product when performing outdoor wiring of a box-type camera for outdoor or a wall mount bracket such as using a conduit.
For the latest information about the supported cameras, refer to our support webfaqe
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information<ControlNo.:C0501,C0502>).

specifikimet

Temperatura e funksionimit të ambientit: -50 ° C deri +60 ° C (-58 ° F deri +140 ° F)
Përmasat: 115 mm (Gj) x 115 mm (L) x 40 mm (D)
(4-17/32 inches (W) x 4-17/32 inches (H) x 1-11/16 inches (D))
Mass: Approx. 430 g (0.95 Ibs)
Mbaro: Base bracket: Aluminum die cast
Attachment plate: Stainless
WV-QJB500-W: i-PRO white
WV-QJB500-S: Silver
VW-QJB500-G: Light gray

* This product consists of an attachment plate and a base bracket and they are separately packaged.

Masat paraprake për instalim

  • In order to prevent injury, the product must be securely mounted to a ceiling or wall according to the Installation Guide of this bracket.
  • Sigurohuni që ta hiqni këtë produkt nëse nuk do të përdoret më.

Pajisje Standard

Operating Instructions (this document) …….. 1 pc.
Installed auxiliary wire* ………………………….. 1 pc.
Hexagon screw …………………………………. 5 pcs.
(M4 × 14 mm {9/16 inches}) (of them, 1 for spare)
Fixing screws for attachment plate ………… 5 pcs.
(M4 × 10 mm {13/32 inches}) (of them, 1 for spare)
Screw for temporary fixing …………………… 2 pcs.
(M3 × 3.5 mm {1/8 inches}) (of them, 1 for spare)

* An installed auxiliary wire is equipped with the attachment plate. 

Sende të tjera që nevojiten (nuk përfshihen)
Fixing screws (M4) …………………. 4 pcs.
E RËNDËSISHME

përgatitjet

Remove the tape fixing installed auxiliary wire (accessory) on the attachment plate.
When installing another bracket on this product
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an examp.

  1. Remove the installed auxiliary wire (accessory) from the attachment plate. iPRO WVQJB500 W Adapter Box - FIG 1
  2. Attach the screw for temporary fixing (accessory) to the bracket to be installed on this product.iPRO WVQJB500 W Adapter Box - FIG 2 Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
  3. If necessary, install the attachment plate provided with the camera to WV-QWL500-W by following the instructions described in the Operating Instructions of WV-QWL500-W.

When using a conduit

  • Remove the cap for the female or thread for the conduit using a 5 mm hex wrench and attach the conduit.
    The female thread for the conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

iPRO WVQJB500 W Adapter Box - FIG 3

Instalim

Step 1: Process the installation surface.
(Screw holes (4 places)/ Cable access hole (1 place))
When directly installing this product, process the installation surface.
Shënim:

  • Determine the fixing screw hole diameter and depth in accordance with the specifications of the screws or anchors (x4) (M4: locally procured).
  • When wiring using a conduit, it is unnecessary to process the cable access hole on the installation surface. Make a fixing screw hole so that the cable access hole (for conduit) of the base bracket is arranged in the direction of the conduit.

Depending on the condition of the ceiling or the wall surface, the following five patterns of screw positions are available for fixation of the base bracket. Use only the holes of the same pattern (A – E) for mounting.

iPRO WVQJB500 W Adapter Box - FIG 4

Vertikale Horizontal
A 83.5 mm {3-9/32 inç} (82.5 mm {3-1/4 inç}) 46 mm {1-13/16 inç} (47.6 mm {1-7/8 inç})
B 46 mm {1-13/16 inç} (47.6 mm {1-7/8 inç}) 83.5 mm {3-9/32 inç} (82.5 mm {3-1/4 inç})
C* 83.5 mm {3-9/32 inç} (83.3 mm {3-9/32 inç}) -
D* - 83.5 mm {3-9/32 inç} (83.3 mm {3-9/32 inç})
E 63 mm (2-15/32 inches} 63 mm (2-15/32 inches}

* When mounting to a single-gang junction box, fix with two fixing screws (M4: locally procured) using the holes of either pattern C or D.

Hapi 2: Fix the base bracket on the installation surface or on a junction box.
Pass the cables through the base bracket and then fix the base bracket on the installation surface or on a junction box (locally procured) with fixing screws (M4: locally procured).
When installing the base bracket on the installation surface
Shënim:

  • When installing this product outdoors, be sure to apply waterproofing to the cable access hole and the holes for fixing the screw.

iPRO WVQJB500 W Adapter Box - FIG 5The illustration shown on the left is an example when installing on a wall using the combination of the fixing screw holes that is 83.5mm {3-9/32inches} × 46mm {1-13/16inches}.

■ When mounting the base bracket to a junction box
Select the holes on the base bracket so that they match with the screw holes of the junction box.
Shënim:

  • When using a two-gang junction box, it is recommended that the boxes are arranged side by side as shown in the illustration below. (The cable connection work on the empty box side will become easier.)

iPRO WVQJB500 W Adapter Box - FIG 6

Step 3: Fix the attachment plate.
Fix the attachment plate with four fixing screws for the attachment plate (M4: accessory).
Recommended tightening torque: 1.37 N·m {1.01 lbf ft}

iPRO WVQJB500 W Adapter Box - FIG 7

Shënim:

  • When wiring using a conduit, complete the connection work on the base bracket side before fixing the attachment plate.
  • When installing this product on a wall, fix the attachment plate with the “TOP⇧” mark facing upward.
  • When installing this product on a ceiling, fix the attachment plate so that the “TOP⇧” mark is faced in the direction where the camera is aiming at.

Hapi 4: Install a camera or other bracket on this product.
■ When installing a camera
The following are descriptions of how to install WV-U1542L (outdoor box type) on a wall using this product as an example. The installation procedure is the same for other cameras.

  1. Hang the camera by hooking the installed auxiliary wire on this product on the hook on the rear of the camera mount base as shown in the illustration on the right.
  2. Connect the cables by following the instructions in the Installation Guide of the camera.
  3. Temporarily fix the camera mount base by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 8iPRO WVQJB500 W Adapter Box - FIG 9
  4. Fix the camera on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}
    iPRO WVQJB500 W Adapter Box - FIG 10

■ When mounting another bracket
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an examp.

  1. Pass the cable through WV-QWL500-W and temporarily fix it by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 11
  2. Fix WV-QWL500-W on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}iPRO WVQJB500 W Adapter Box - FIG 12
  3. Install the camera by following the Operating Instructions of WV-QWL500-W.
  • Para se të përpiqeni të lidhni ose instaloni këtë produkt, ju lutemi lexoni me kujdes këto udhëzime dhe ruajeni këtë manual për përdorim në të ardhmen.
  • Pamja e jashtme dhe pjesët e tjera të treguara në këtë manual mund të ndryshojnë nga produkti aktual brenda fushës që nuk do të ndërhyjë në përdorimin normal për shkak të përmirësimit të produktit.

i-PRO Co., Ltd. nuk merr asnjë përgjegjësi për lëndimet ose dëmtimet pronësore që vijnë nga dështimet që vijnë nga instalimi ose funksionimi jo i duhur, në kundërshtim me këtë dokumentacion.

Kujdes: Njoftim:
• Before attempting to connect or operate this product, please read these instructions carefully. • This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily
reach it.
• For information about screws and brackets required for installation, refer to the corresponding section of this document.

Për SH.B.A. dhe Kanada:
i-PRO Americas Inc.
Për Evropën dhe vendet e tjera:
i-PRO EMEA BV
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
iPRO WVQJB500 W Adapter Box - BAR CodeNS0520-1042
Shtypur në Kinë

Dokumentet / Burimet

i-PRO WV-QJB500-W Adapter Box [pdf] Manuali i udhëzimeve
WV-QJB500-W, Adapter Box, WV-QJB500-W Adapter Box, Box

Referencat

Lini një koment

Adresa juaj e emailit nuk do të publikohet. Fusha e kërkuar janë shënuar *