Soundpeats Truefree Plus

Soundpeats Truefree Plus

Package Content

Package Content

Product Diagram

Product Diagram
  1. Multifunction Button
  2. LED Indicator
  3. Microphone
  4. Charging Contactor
  5. Charging Case
  6. Charging Slot
  7. USB Charging Port
  8. Charging Case LED Indicator


Package Content


  1. Identify the left and right earbuds.
  2. Insert the earbuds into your ears and adjust to nd best angle with microphone downwards.
  3. Make sure the eartips seal the ear canals.

Get Started

Mono Mode

  1. The earbud enters pairing mode directly with a voice prompt “power on” aer
    being taken out from the charging case. White indicator ashes quickly for around 10s, then red and white indicators ash alternately with a voice prompt “pairing”. “SOUNDPEATS TrueFree+ L” or “SOUNDPEATS TrueFree+ R” would show up on the Bluetooth list, hit it to connect.
  2. If you want to connect two earbuds separately with 2 devices nearby, please
    connect the le one to one device at rst. In case it will connect to the right earbud automatically aer being taken out from the charging case.

Stereo Mode

Take out both earbuds from the charging case. The two earbuds will ash in white
at rst. Then the le indicator goes out, and right indicator ashes in red and white.
Activate the Bluetooth in your device and hit “SOUNDPEATS TrueFree+ R” on the
Bluetooth list.

Factory Reset

(Try the following steps if you fail building connection between two earbuds, or between earbuds and device)

  1. Clear the pairing record between the earbuds and all of your devices.
  2. Hold and press the MFB of both earbuds for 10 seconds when in charging status, the LED indicator will ash red for 3 times if resetting successfully.


  1. Please charge the earbuds at least once every 3 months when not in use for a long time.
  2. To ensure charging safety, please do not use any USB charging adapter with current over 5V 1A. Please do not use quick charger to charge the earbuds and charging case.


  1. If you don’t know which device the earbud has already connected, please turn
    it off, then press and hold the button for 5 seconds until red and white indicator
    flashes alternately to have the earbud enter pairing mode again.
  2. If pairing device is switched o or Bluetooth disconnected, the earbuds will stay in pairing mode for 5 minutes and then power o automatically.
  3. The earbuds can remember previously paired devices. They would automatically
    connect to the last device they have paired before aer being taken out from
    the case.

Button Control

Power On

LED Indicators


We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects. [email protected] Please scan the QR code or search the link below for detailed PDF manual :

QR code or search the

Questions about your Manual ? Post in the comments!

Join the Conversation


  1. Sometimes I stop play in an earbud and want to use my iPod controls instead of the earbud, but the iPod doesn’t respond. To my touch.

  2. Can’t connect earbuds to my Samsung Galaxy 10+. They connect okay to my iPad but for some reason not the Samsung phone?

  3. Download the Soundpeats app from the store. Once it’s on your Samsung 10+, the buds should pair properly and work .

  4. hi I need a usb charging adapter for my soundpeats true wireless earbuds 5.0 bluetooth headphones in ear. can you tell me where i can purchase one

  5. The volume is very, very low even though I have all the volume on my cell phone 🙁
    Se escucha muy, muy bajo el volumen a pesar de que tengo todo el volumen en mi celular 🙁

    1. Same thing happened to my wife’s. She disconnected the earbuds Bluetooth connection to her phone (Android) by “Forget” and did a fresh Bluetooth re-connection and volume ok. Hope it helps.

Leave a comment

Your email address will not be published.