USER MANUAL

Soundpeats Q32Pro

Soundpeats
Model: Q32 Pro

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeatsaudio.com

Package Content

Package Content

Product Diagram

Product Diagram

Specifications

Specifications

Wearing

  1. Identify the le and right earbuds.
  2. Insert the earbuds into your ears and adjust to nd best angle with microphone downwards.
  3. Make sure the eartips seal the ear canals.
Wearing

Get Started
Mono Mode

  1. The earbud enters pairing mode directly with a voice prompt “power on” aer being taken out from the charging case. White indicator ashes quickly for around 10s, then red and white indicators ash alternately with a voice prompt “pairing”. “SOUNDPEATS Q32 Pro L” or “SOUNDPEATS Q32 Pro R” would show up on the Bluetooth list, hit it to connect.
  2. If you want to connect two earbuds separately with 2 devices nearby, please connect the le one to one device at rst. In case it will connect to the right earbud automatically aer being taken out from the charging case.

Stereo Mode
Take out both earbuds from the charging case. The two earbuds will ash in white at first. Then the le indicator goes out, and right indicator ashes in red and white. Activate the Bluetooth in your device and hit “SOUNDPEATS Q32 Pro R” on the Bluetooth list.

Factory Reset
(Try the following steps if you fail building connection between two earbuds, or between earbuds and device)

  1. Clear the pairing record between the earbuds and all of your devices.
  2. Hold and press the MFB of both earbuds for 10 seconds when in charging status, the LED indicator will flash red for 3 times if resetting successfully

Charge

  1. Please charge the earbuds at least once every 3 months when not in use for a long time.
  2. To ensure charging safety, please do not use any USB charging adapter with current over 5V 1A. Please do not use quick charger to charge the earbuds and charging case.
Charge

Note:

  1. If you don’t know which device the earbud has already connected, please turn it off then press and hold the button for 5 seconds until red and white indicator flashes alternately to have the earbud enter pairing mode again.
  2. If pairing device is switched off or Bluetooth disconnected, the earbuds will stay in pairing mode for 5 minutes and then power o automatically.
  3. The earbuds can remember previously paired devices. They would automatically connect to the last device they have paired before aer being taken out from the case.

Button Control

Button Control

LED Indicators

LED Indicators

Warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects.
[email protected]
www.soundpeatsaudio.com
Please scan the QR code or search the link below for detailed PDF manual :
https://soundpeatsaudio.com/downloads/

downloads

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B English digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Leave a comment

Your email address will not be published. Required fields are marked *