SONOFF MINI Dry Wi-Fi Smart Switch User Guide

A: Short-circuit the terminals of the motor originally used for wall switch connection. If the motor operates after short-circuiting, it is compatible.

Power oﬀ

WARNING
Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

Wiring instruction

WARNING

AC and DC are not supported as power input at the same time!

DC low power load wiring

Dry contact wiring

Applicable to devices that can be controlled via dry contact.
To ensure compatibility with the garage door motor, please short-circuit the terminals of the motor that were originally used to connect to the wall switch ( the short-circuiting process is safe, so don’t worry). If the garage door motor operates after short-circuiting, it is compatible; if the motor does not operate, it is not compatible.
1. Applicable to devices that can be controlled via dry contact.
2. To ensure compatibility with the garage door motor, please short-circuit the terminals of the motor that were originally used to connect to the wall switch ( the short-circuiting process is safe, so don’t worry). If the garage door motor operates after short-circuiting, it is compatible; if the motor does not operate, it is not compatible.
  
  Make sure all wires are connected correctly

Download the eWeLink App

Power on

After powering on, the device will enter the Pairing Mode during the first use. The LED indicator changes in a cycle of two short and one long flash and release

Check the Device Status

External Switch Type: The device’s factory default is the rocker switch. To switch to the momentary switch, you need to short-press the device button three times. If the blue light flashes three times, it means the switch is successful.

Add Device

Method 1: Matter Pairing

Open a Matter-compatible App to scan the Matter QR code on the Quick Guide or the device itself to add the device.

Method 2: eWeLink App Pairing

Open the eWeLink App and scan the QR code on the device, then follow the instructions given by the app to proceed.

Install the device in the mounting box

This product is only suitable for safe use at altitudes below 2000m

User Manual

https://sonoff.tech/usermanuals

Enter the website provided above to view the User Manual for the device

To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current operated
Cicuit-breaker with Integral Overcurrent protection(RCBO) with an electrical rating of 2A has been installed before the MINI-D,MINI-D-MS

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

FCC compliance statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC ID: 2APN5MINI-D

Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

Pollution degree: II
Rated impulse voltage: 4KV
Automatic action: 20000 Cycles
Diameter of wiring(recommend): 18AWG to 14AWG（0.75mm² to 1.5 mm² ）
Casing material: PC
Control Type: 1.B
Operating temperature: 10T40
Operating altitude: 2000M

EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type MINI-D, MINI-D-MS is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance/

For CE frequency
EU Operating Frequency Range

Wi-Fi：
802.11 b/g/n20 2412–2472 MHz
802.11 n40: 2422-2462 MHz
BLE: 2402–2480 MHz

EU Output Power
Wi-Fi 2.4G≤20dBm
BLE≤10dBm

Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000 Website: sonoff.tech Service email: support@itead.cc
MADE IN CHINA

Documents / Resources

	SONOFF MINI Dry Wi-Fi Smart Switch [pdf] User Guide MINI Dry Wi-Fi Smart Switch, MINI Dry, Wi-Fi Smart Switch, Smart Switch, Switch
	SONOFF MINI Dry Wi-Fi Smart Switch [pdf] User Guide MINI Dry Wi-Fi Smart Switch, MINI Dry, Wi-Fi Smart Switch, Smart Switch, Switch

References

User Manual

SONOFF MINI Dry Wi-Fi Smart Switch

Specifications

FAQ