SOFIRN SD11 Flashlight (Overview)
The SOFIRN SD11 is a rechargeable flashlight with Cool White, Warm White, Neutral White, and Red light modes, including strobe/flash functions. It features a battery status indicator, brightness regulation for low power and temperature control, and a rotary Hall-effect switch for mode selection.
Specifications
| Power / Battery | Product Power: 57W |
| Battery Capacity: 7500mAh | |
| Charging Input: DC 5V/3A (max) | |
| Time to Fully Charge: About 3h | |
| Light Output (Lumens) & Runtime (as listed) | Neutral White Light Turbo (Land): 5000 ➔ 2500 ➔ 1300 lm (1min + 3min + 2.1h) Turbo (Diving): 5000 ➔ 3300 ➔ 1300 lm (1min + 40min + 25min) Warm White Light Turbo (Land): 2200 ➔ 1000 ➔ 850 lm (1min + 3min + 2.75h) Turbo (Diving): 2200 ➔ 1000 ➔ 850 lm (6min + 40min + 1h) High: 1200 ➔ 850 lm (5min + 3h) Medium: 700 lm (4.5h) Low: 300 lm (11h) Cool White Light Turbo (Land): 3200 ➔ 1500 lm (2min + 2.1h) Turbo (Diving): 3000 ➔ 2200 ➔ 1500 lm (6min + 40min + 1h) High: 1600 ➔ 1000 lm (5min + 3h) Medium: 800 lm (5.25h) Low: 400 lm (11.2h) Red Light Strobe: 150 lm (9h) High: 150 lm (4.5h) Medium: 70 lm (12.5h) Low: 30 lm (32h) |
Quick Setup & Operation
- Charge the flashlight: Connect the supplied Type-C charging cable to the charging port.
- Check battery status: With the flashlight powered OFF (or after switching to another mode), the battery indicator shows status for 5 seconds (Solid/Flashing Green, Solid/Flashing Red).
- Select a light mode: Use the rotary Hall-effect switch to choose OFF / Cool White / Warm White / Red.
- Cycle brightness in Cool/Warm White modes: Press the touch button once to cycle Low ➔ Medium ➔ High ➔ Turbo.
- Jump to Neutral White at max: While in Cool or Warm White, press the touch button twice to switch immediately to Neutral White at 5000 lm. Press once to return to the previous light mode.
- Control Red light: In Red mode, press once to cycle Low ➔ Medium ➔ High. Press twice for Red Flashing (strobe). Press once to return to the previous state.
SOFIRN USER MANUAL
SD11

In the Box
- SD11 Flashlight
- Lanyard
- O-Rings
- Type-C Charging Cable
- User Manual
Specifications
Table 1 (Light Output Specifications)
| Neutral White Light | ||
|---|---|---|
| Turbo (Land) | 5000 ➔ 2500 ➔ 1300 lumens | 1min + 3min + 2.1h |
| Turbo (Diving) | 5000 ➔ 3300 ➔ 1300 lumens | 1min + 40min + 25min |
| Warm White Light | ||
| Turbo (Land) | 2200 ➔ 1000 ➔ 850 lumens | 1min + 3min + 2.75h |
| Turbo (Diving) | 2200 ➔ 1000 ➔ 850 lumens | 6min + 40min + 1h |
| High | 1200 ➔ 850 lumens | 5min + 3h |
| Medium | 700 lumens | 4.5h |
| Low | 300 lumens | 11h |
| Cool White Light | ||
| Turbo (Land) | 3200 ➔ 1500 lumens | 2min + 2.1h |
| Turbo (Diving) | 3000 ➔ 2200 ➔ 1500 lumens | 6min + 40min + 1h |
| High | 1600 ➔ 1000 lumens | 5min + 3h |
| Medium | 800 lumens | 5.25h |
| Low | 400 lumens | 11.2h |
| Red Light | ||
| Strobe | 150 lumens | 9h |
| High | 150 lumens | 4.5h |
| Medium | 70 lumens | 12.5h |
| Low | 30 lumens | 32h |

Table 2 (Battery Specifications)
| Input | DC 5V/3A (max) |
| Time To Fully Charge | About 3h |
| Product Power | 57W |
| Battery Capacity | 7500mAh |
Product Overview
Figure 1

Instructions and Operation
1. Battery Charging & Status Indicator
Figure 2 (Charging Setup)

When the flashlight is powered OFF or after switching to another mode, the battery indicator will display the current battery status for 5 seconds:
- Solid Green: 75% – 100%
- Flashing Green: 50% – 75%
- Solid Red: 25% – 50%
- Flashing Red: 1% – 25% (Please recharge promptly)
During Charging:
- Solid Red: Charging in progress
- Solid Green: Fully charged

2. Battery & Device Protection
- Low Power, Brightness Reduction: When the battery power runs low, the flashlight automatically reduces brightness to maintain optimal efficiency relative to the current voltage.
- Low Voltage Protection: If the battery voltage drops below a critical point while powered on, the flashlight shuts down automatically to prevent battery damage.
- Temperature Control Protection: If the device reaches its preset heat threshold during operation, it automatically regulates and lowers output brightness to prevent overheating.
3. Switching Modes
Figure 3

![]()
Use the rotary Hall-effect switch to select the operating modes: OFF / Cool White Light / Warm White Light / Red Light Modes.
4. Cool White / Warm White Mode Control
Figure 4 (Cool/Warm White Light Cycles)

- Press the touch button once (*1) to cycle sequentially through the brightness steps: Low ➔ Medium ➔ High ➔ Turbo.
5. Activating Neutral White Light Mode
Figure 5 (Neutral White Light Shortcut)

- While in Cool White or Warm White mode, press the touch button twice (*2) to immediately jump to Neutral White Light Mode at maximum brightness (5000 lm).
- Press the button once (*1) to exit and return to the previous light mode.
6. Red Light Mode Control
Figure 6 (Red Light Cycles)

- In Red Light mode, press the touch button once (*1) to cycle brightness steps sequentially: Low ➔ Medium ➔ High.
- Press the button twice (*2) to activate Red Flashing mode.
- Press once (*1) to return to the previous state.
Warnings & Safety Precautions
WARNING ⚠ Always power off the flashlight completely when storing it in a pocket, backpack, or any enclosed or potentially flammable space, or during periods of long-term storage, to avoid extreme heat generation and hazardous conditions.
Safety and Maintenance Cautions
- This flashlight is a high-performance lighting device. Do not look directly into the beam or shine it into anyone’s eyes to prevent vision impairment.
- Intended for use by adults aged 18 and older. Keep the device out of reach of children.
- After diving, thoroughly rinse the flashlight with clean fresh water to wash away saltwater and debris, preventing corrosion.
- Do not cover the light head or place any objects directly against the lens while turned on to prevent accidental burns or heat damage.
- Avoid operating or storing the flashlight in ambient temperatures exceeding 60 °C (140 °F) to preserve components and battery health.
- For long-term storage, recharge the battery every six months to prevent deep discharge degradation.
- Do not attempt to disassemble, modify, or rebuild the flashlight. Unauthorized modifications will void the warranty and may cause electrical shorts or failures.
- Only charge the device using the supplied Type-C charging cable.
- If utilizing this flashlight as a designated safety or emergency device, test and cycle the light monthly to verify operation.
- Check the waterproof O-rings for signs of wear or damage after every dive. Replace them immediately if worn to ensure waterproof performance. After charging, make sure the charging port cover is tightly closed against water and dust intrusion.
Manufacturer Information
SOFIRN Shenzhen City Jinba Technology Co., Ltd.
Address: 1501, Building B, Rongchao New Era Plaza, No.3 Lanjing 1st Road, Luhu Community, Guanhu Street, Longhua District, Shenzhen City, 518000, China
Made in China


THANK YOU!
Troubleshooting
- Battery status is low: If the battery indicator shows flashing red (1%–25%), recharge promptly.
- Brightness suddenly reduces: The flashlight automatically reduces brightness when battery power runs low to maintain efficiency.
- Flashlight shuts down while on: Low voltage protection may trigger if battery voltage drops below a critical point; recharge the battery.
- Output gets lower due to heat: Temperature control protection regulates and lowers output when the device reaches its preset heat threshold to prevent overheating.
- Water/dust intrusion concerns (especially after diving/charging): Rinse thoroughly after diving with clean fresh water; ensure charging port cover is tightly closed after charging; check O-rings for wear/damage after every dive and replace if worn.
- Does not charge properly: Only charge using the supplied Type-C charging cable (as instructed). Ensure the provided charging input matches DC 5V/3A (max).
FAQ
- How can I see the battery status on the SD11?
- With the flashlight powered OFF (or after switching to another mode), the battery indicator displays battery status for 5 seconds: Solid Green (75%–100%), Flashing Green (50%–75%), Solid Red (25%–50%), Flashing Red (1%–25%).
- What do the battery protections do if the flashlight runs low on power or gets hot?
- The flashlight reduces brightness when battery power runs low, shuts down if low voltage protection detects a critical voltage while powered on, and lowers output when temperature control protection reaches its preset heat threshold to prevent overheating.
- How do I switch to Neutral White mode at maximum brightness?
- While in Cool White or Warm White mode, press the touch button twice to jump to Neutral White at maximum brightness (5000 lm). Press once to return to the previous light mode.
- How do I control Red light and Red Flashing on the SD11?
- In Red mode, press once to cycle Low ➔ Medium ➔ High. Press twice to activate Red Flashing mode. Press once to return to the previous state.
Documents / Resources
![]() | SD11 Scuba Diving Flashlight |
References
- User Manualmanual.tools
