INSTRUCTION MANUAL
1CH,2CH,3CH,4CH
Zigbee Switch Module
TECHNICAL SPECIFICATIONS
| Product type | Zigbee Switch Module |
| Voltage | AC100-240V 50/60Hz |
| Max. load |  1CH: 10A/16A 2CH: 2x5A3CH: 3×3.3A 4CH: 4×2.5A |
| Operation frequency | 2.405GHz-2.480GHz |
| Operation temp. | -10 ℃ + 40℃ |
| Protocol | IEEE802.15.4 |
| Operation range | <100m |
| Dims (WxDxH) | 39.2×39.2×18 mm |
| IP rating | IP20 |
| Warranty | 2years |
| Certificates | CE ROHS |
With mounting clip
INSTALLATION
Warnings:
- Installation must be carried out by a qualified electrician in accordance with local regulations.
- Keep the device out of reach of children.
- Keep the device away from water , damp or hot environment.
- Install the device away from strong signal sources such as microwave oven that may cause signal interruption resulted to abnormal operation of the device.
- Obstruction by concrete wall or metallic materials may reduce the effective operation range of the device and should be avoided.
- Do NOT attempt to disassemble, repair or modify the device.
FAQ
What should I do if I can’t configure the switch module?
a. Please check whether device is powered on. b. Make sure the Zigbee Gateway is available. c. Whether it’s in good internet conditions. d. Make sure the password entered in App is correct. e. Make sure the wiring is correct.
What device can be connected to this Zigbee switch module?
Most of your household electrical appliances, such as lamps, laundry machine, coffee maker, etc.
What happens if the WIFI goes off?
You can still control the device connected the witchmodule with your traditional switch and once WIFI is active again the device connected to module will connect automatically to your WIFI network.
What should I do if I change the WIFI network or change the password?
You have to re-connect our Zigbee switch module to the new Wi-Fi network accordingly as per the App User
How do I reset the device?
1. Power on/off device for 5 times until the indicator light flash. 2. Switch on/off the traditional switch for 5 times until the indicator light flash. 3. Press the reset key for about 10 seconds until the indicator light flash.
Wiring Instructions and Diagrams
Without Switch
1CH Zigbee Switch Module
Single Control
Double Switch
2CH Zigbee Switch Module
Without Switch
Single Control
Double Switch
3CH Zigbee Switch Module
Without Switch
Single Control
Double Switch
4CH Zigbee Switch Module
Without Switch
Single Control
- IOS APP / Android APP
Scan the QR code to download Tuya Smart App, or you can also search keyword “Tuya Smart” at App Store or Googleplay to download App.
http://smart.tuya.com/download
Log in or register your account with your mobile number or e-mail address.Type in the verification code sent to your mobile or mail box, then set your login password. Click “Create Family” to enter into the APP.
- After the wiring of switch module is done, press the reset key for about 10 seconds or turn on/off the traditional switch for 5 times until the indicator light inside the module is flashing quickly for pairing.
- Click “+” (Add sub-device) to select the suitable product gateway and follow the on-screen instruction for paring.
Finally, you can control the device via your mobile phone.
- After the wiring of switch module is done, press the reset key for about 10 seconds or turn on/off the traditional switch for 5 times until the indicator light inside the module is flashing quickly for pairing.
SYSTEM REQUIREMENTS
WIFI® Router
ZigBee gateway
iPhone, iPad (iOS 7.0 or higher)
Android 4.0 or higher
Documents / Resources
 | Zigbee 1Ch Universal Smart Switch [pdf] Instruction Manual 1Ch Universal Smart Switch, Universal Smart Switch, Smart Switch, Switch |