URC UR2-DTA DTA Remote Control

UR2-DTA DTA Remote Control
The UR2-DTA is a universal remote control designed to operate S/A, Pace Micro, Motorola, and IPTV set tops, as well as the majority of TV equipment on the market. It provides convenient control over your DTA box, IPTV set tops, and televisions.

Replacing Batteries

Before programming or operating the remote control, you need to install two new AA alkaline batteries. Follow these steps:

1. Remove the battery compartment cover on the back of your remote control.
2. Check battery polarity carefully and install the batteries as shown in the illustration below.
3. Replace the battery compartment cover.

Operations
The default setting for volume control is through the DTA. However, you have the option to control volume and mute through your TV. Refer to Section F for programming instructions.

Button Functions
The remote control offers various button functions to control your devices.

Programming the Remote Control
There are three methods to program your remote control:

1. Quick Set-Up Method
2. Pre-Programmed 3-Digit Code Method
3. Auto-Search Method

IMPORTANT SETUP NOTE!
During setup mode, the DTA LED will light for 20 seconds. If you don’t press a button within this time, the LED light will turn off and exit setup mode. You will need to start over.

Quick Set-Up Method

1. Turn on the component you want to program. For programming the TV, turn on the TV.
2. Press and hold the [DEVICE] key for 5 seconds until the DTA LED blinks once and stays on.
3. Continue holding the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table.
4. Release both the [DEVICE] key and the number key to save the code. The DTA LED will blink twice to confirm that the code is stored.
5. Point the remote control at the component.
6. Press the power button. If the component turns off, it is successfully programmed. If not, proceed with the Pre-Programmed 3-Digit Code Method or Scanning Method.
7. Repeat the above steps for all components (DTA, TV).

B. Quick Set-up Code Tables
Use the Quick Set-up Code Tables below to find the number associated with your brand:

C. Pre-Programmed 3-Digit Code Method

1. Turn on the component you want to program (TV, DTA).
2. Press the [DEVICE] button (TV or DTA) to be programmed and the [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds, indicating that the unit is ready to be programmed.
3. Point the remote control toward the component and enter the 3-digit code number assigned to your brand.
4. If the component turns off, the entered code is correct. If it doesn’t turn off, continue entering code numbers listed for that brand until the component turns off.
5. Once you find the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored.

Now you can enjoy controlling your devices using the UR2-DTA DTA Remote Control!

Introduction

The UR2-DTA is designed to operate the S/A, Pace Micro, Motorola and IPTV set tops, plus the majority of TV equipment on the market as shown below.

• DTA : DTA boxs, IPTV set tops
• TV : Televisions

Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

• STEP1 Remove the battery compartment cover on the back of your remote control.
• STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
• STEP3 Replace the battery compartment cover.

Operations

Volume Default: DTA volume and mute through the DTA, with the option of controlling volume and mute through the TV. Refer to Section F for programming the volume and mute through your TV.

Button Functions

Programming the Remote Control

There are three ways you can program your remote:

• Quick Set-Up Method
• The Pre-Programmed 3-Digit Code Method
• The Auto-Search Method

The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component.
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time.

IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, the DTA LED will light for 20 seconds. If you do not press a button within 20 seconds, the LED light will turn off and exit setup mode and you will need to start over.

A. Quick Set-Up Method

• STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
• STEP2 Press and hold the [DEVICE] key for 5 seconds until the DTA LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table and release both [DEVICE] key and the number key to save the code. The DTA LED will blink twice to confirm that the code is stored.
• STEP3 Point the remote control at the component.
• STEP4 Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method.

Repeat the steps above for all components. (DTA, TV).

B. Quick Set-up Code Tables

DTA

TV

C. Pre-Programmed 3-Digit Code

Method

• STEP1 Turn on the Component you want to program(TV, DTA).
• STEP2 Press the [DEVICE] button (TV or DTA) to be programmed and [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds indicating the unit is ready to be programmed.
• STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand.
  *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off.
• STEP4 Once you have found the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored.

Auto-Search Method

• STEP1 Turn on the Component you want to program (TV, DTA).
• STEP2 Press the [DEVICE] button (TV or DTA) to be programmed and [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds indi-cating the unit is ready to be programmed.
• STEP3 Point the remote toward the Component and press the [CH5] or [CH6] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH5] or [CH6] button as soon as the Component turns Off.
• STEP4 Once you have found the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored. Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre-Programmed Method.

E. Finding a Component Button’s

Setup Code Number
If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference.

• STEP1 Press the [DEVICE] button (TV or DTA) you want to verify and the [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds.
• STEP2 Press the [INFO] button and count the number of times the DTA LED light blinks. This num-ber indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off.
  • *Note : 10 blinks represents the number zero.
  • Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183.

F. Programming Volume Control

By default, the VOL+, VOL- and MUTE keys operate through your DTA. If you would like those keys to operate those functions on a TV device, follow these steps.

• STEP1 Press the [SEL] button and [DTA] button simultaneously for 3 seconds.
  • The DTA LED will turn on for 20 seconds.
  • The next step must be perfumed while the LED is on.
• STEP2 Press the [VOL+] button.
  • The DTA LED will blink.
• STEP3 Press the [TV] button that you would like the volume and mute buttons to control. The DTA LED will blink twice to confirm the programming.

Note : If you wish to have the volume and mute keys operate your DTA Box, press the [DTA] device button in Step 3.

G. Memory Lock System
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

H. Write your TV Set-up codes
Set-up Code Number : For additional information about your remote control, go to www.universal-remote.com

Set­up Code Tables

DTA

DTA

TV

TV

TV

TV

TV

TV

TV

Universal Remote Control, Inc.
www.universalremote.com
OCE-0089B REV 18 (03/21/23)

Documents / Resources

URC UR2-DTA DTA Remote Control [pdf] Instruction Manual UR2-DTA DTA Remote Control, UR2-DTA, DTA Remote Control, Remote Control, Control

References

• User Manual