RIBIMEX PRCOMP1-06SILR Air Compressor

MODELS

WARNING:
Carefully read this instruction manual before operating this appliance. Incorrect operation may cause injury and/or damages.
Please keep this manual for future reference.

Note : Non-contractual information and photos, which may be changed without prior notice.
Actual product may differ from illustrative photos.
Subject to technical changes and improvements.

PARTS LIST

CHARACTERISTICS

SAFETY INSTRUCTIONS

Save all warnings and instructions for future reference.

Keep this manual handy so that you may refer to it later whenever any questions arise. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product.

Symbols (Explanation of symbols appearing on the tool, if applicable)

General safety warnings

• Understand the product. Read and follow the instructions in this manual.
• Do not disassemble or modify the product.
• Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged.
• Maintain good housekeeping and sufficient lighting in the working area.
• Keep children and bystanders away while operating this product.
• Cleaning and user maintenance shall not be made by children.
• Use attachments/accessories specified by the manufacturer.
• Perform service maintenance by qualified personnel only.
• Dress properly. Do not wear loose clothing or jewelry. Keep hair, clothing and gloves away from moving parts.

Additional safety rules for electric power tool

• When the tool is not in use or before performing cleaning, turn it off and disconnect from main power source.
• Never leave the product running unattended.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
• Maintain labels and rating plate through the life of service.
• Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
• Store idle power tool out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
• If the power cable is damaged, it must be replaced by the manufacturer, its after sales service or a person with similar qualification in order to avoid any danger.

Special warnings when using these air compressors

• Use personal protective equipment. Always wear hearing protection when using the tool.
• To minimize the impact of emitted noise and vibration, limit the operation time and wear appropriate personal protective equipment.
• Do not use the tools in any operations that beyond the intended purpose.
• Do not direct compressed air at yourself, other persons or animals.
• Do not insert your body parts (such as fingers) or other objects inside the motor housing to avoid injury to yourself or damage to the compressor.
• The compressor should be used for air compression only. Do not use the compressor for any other types of gas.
• The compressed air produced by the compressor may only be used for pharmaceutical, food or medical purposes after special treatments only and cannot be used to fill divers’ air cylinders.
• Never leave the device in bad weather.
• he air compressor must be installed in a suitable and well-ventilated environment, the ambient temperature must be between +5 and +40°C.
• The work area must be free of dust, acid vapors, explosive gases and flammable materials.
• Do not exceed the maximum air pressure rating for the accessory.
• Use only hoses or connectors designed for use with compressed air. The maximum working pressure of the hoses and fittings must be greater than the maximum working pressure of the compressor.
• This compressor must be connected to main electricity protected by an appropriate circuit breaker or fuse.
• Use extension cables with a maximum length of 5 meters.
• Always use the handle to move the compressor. Do not attempt to move the compressor by pulling on the air hose or electrical cable.
• During operation, the compressor must be securely installed on a stable and horizontal surface.
• Avoid kinking or pinching the air hose.
• When using compressed air, you must observe and follow the safety precautions for the type specific application (such as inflation, pneumatic tools, painting, washing with water-based detergents, etc.).
• The pump and compressor lines may become very hot during operation. Avoid touching these parts during operation.
• Empty the tank after each use. Turn off and slowly open the drain valve to release the air, then tilt the compressor to drain the condensed water.
• Always transport the compressor by lifting or pulling it with the appropriate grips or handles.
• Always replace defective hoses – never attempt to repair if a leak is detected.
• Keep the engine vent clear and free of dust, wipe it regularly to maintain an adequate supply of clean air to the air compressor.
• Never clean the compressor with flammable liquids or solvents. Make sure you have unplugged the compressor and clean it with a damp cloth.

GETTING STARTED

Unpacking

• Remove the product from packaging
• Check if the product and accessories (if any) are intact.

Assembly

WARNING!
Before starting assembly or changing accessories, turn it off and disconnect from main power source.

• Fitting the main wheel (10)
  • Fit the main wheel as shown in Fig. 2.
  • “a” denotes nut; “b” denotes washer; “c” denotes wheel; “d” denotes bolt.
• Fitting the supporting foot (3)
  • Fit the supporting foot as shown in Fig. 3.
  • “e” denotes nut; “f” denotes supporting foot; “g” denotes bolt.
• Fitting the air intake filter (1)
  • Fit the air intake filter as shown in Fig. 4.
  • “h” denotes air intake filter.
• Power supply
  
  • Use the original power cord and plug supplied with the product.
  • The compressor must be connected to the 220-240V ~ 50Hz mains supply.
  • Long cables, extensions, cable reels… etc. cause a drop in input voltage and can impede motor start-up.
  • In case of ambient temperature below +5 °C, motor start-up is jeopardized as a result of stiffness.

Power On/Off

• To turn on the compressor, turn the power switch (5) to the ON (upper) position.
• To turn off the compressor, turn the power switch (5) to the OFF (lower) position.

OPERATION

Intended use

The air compressors are intended for generating and supplying compressed air to pneumatic power tools and tyres. They are not suitable for inflating small-volume items or continuous operation. They are designed for private domestic use only, not for artisanal, commercial, professional and/or industrial use.

NOTE: The compressors are intended for compressing atmospheric air only and strictly prohibits compressing any other gases.

Operation

Preparation for use
Before connecting the compressor to the mains, check the following points:

• Mains voltage is 220-240V ~ 50Hz.
• The power switch is in the OFF (lower) position.
• Install the compressor in the vicinity of the point of consumption.
• Make sure that the intake air is dry and dust free.
• The pressure regulator should be set to its lowest setting, i. e. turned fully counterclockwise.
• If the machine has not been used for more than 24 hours, open the drain plug (“i” in Fig. 5) to drain any accumulated condensate. After cleaning the condensed water, hand tighten the drain plug.

Starting the air compressor 

• Make sure the air outlet pressure regulator (8) is closed.
• Turn on the compressor by setting the power switch to the ON (upper) position, refer to clause 4.3 for details.
• When the air receiver tank is pressurized to its operating state, the compressor will automatically shut down.
• Check all valves and regulators for leaks.

Connecting accessories and regulating pressure 

• WARNING! Do not operate an accessory with pressure greater than the maximum rated pressure of the accessory.
• Connect the accessory to the quick-lock coupling (9).
• Slowly open the outlet pressure regulator (8) until the pressure gauge (6) indicates minimum pressure for the accessory.
• Fine adjustments to the air pressure until the accessory is working at its optimum performance.

After use 

• Turn off the compressor by pressing the power switch (5), refer to clause 4.3 for details.
• Disconnect the accessory tool from the compressor, if necessary.
• Turn the regulator (8) counterclockwise all the way and allow the compressor to cool down.
• Release the residual air pressure in the tank by connecting and operation an air duster.

Overload protection

• The compressor is equipped with an overload switch. If the motor becomes too hot, the overload switch will trip and the equipment will automatically shut down to protect the compressor from overheating.
• If the overload switch has tripped, turn the power switch (5) to the OFF position and wait for the compressor to cool before restarting.

MAINTENANCE AND STORAGE

WARNING!
Before any intervention on product, ensure that power is set to the “OFF” position and disconnect from main power source.

WARNING!
Users should only carry out maintenance work in accordance with this instruction manual. All other service work must be carried out by an authorized service center.

Reminder: In order to maintain the machine in good working condition, carry out regular maintenance of the machine after each use and before storage. Any breach or inadequate maintenance reduces the life of the machine and increases the risk of breakdowns and accidents.

Cleaning

• Disconnect the hose and all accessories from the compressor before cleaning.
• Whenever possible, keep safety devices free of dirt and dust. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure (max. 3 bar).
• Do not use aggressive detergents, chemicals or solvents for cleaning; these may be aggressive to the plastic parts. Make sure no water can get into the interior of the product.

Maintenance

• Condensed water
  
  • Turn off the compressor and disconnect the hose and all accessories from it.
  • Release any residual pressure in the tank.
  • Loosen the drain plug and drain the condensed water every day after use.
  • NOTE: The condensation water from the pressure tank may contain residual engine oil. Collect and dispose of condensation water in an environmentally friendly manner at your local collection point.
  • Check and hand tighten the drain plug.
• Safety valve
  • The safety valve (7) has been set to the maximum permitted pressure of the pressure tank. User should not adjust the safety valve.
• Air intake filter 
  • The air intake filter (1) prevents dust and dirt from being drawn into the compressor. A clogged filter will significantly reduce compressor performance.
  • Clean the air intake filter every 300 hours of operation. Perform cleaning more frequently if the environment is dusty.
  • Remove the air filter from the air compressor, then open the filter housing. Use compressed air (approx. 3 bar) to blow debris from the filter. Assemble and install the intake filter after cleaning.

Troubleshooting

Storage

• Clean the product before storage.
• Keep the product, instruction manual and accessories (if any) in the original packaging.
• Store the product in a clean environment, where is not freezing or too hot (exceed 50 ̊C).
• Keep out of reach of children (e.g., lock it up).

Disposal

• Do not dispose with household garbage. Do not throw into the environment.
• Dispose of the product in a collection centre for waste of electrical and electronic equipment, or a waste drop-off centre; or seek advice from your local municipality.
• Proceed with disposal of the tool, accessories and packaging according to local regulations regarding the protection of the environment.

CONTACT

• Our warranty conditions are available from our STAV department [*] and on our website. Should you have any repair requests under the warranty, please contact your retailer or our STAV [*] who will inform you on the procedure.
• Should you have any parts and/or accessories request, you can contact our STAV [*] to ask for the product exploded view by indicating our reference and the serial number or batch number appearing on the nameplate.
• [*] STAV = Technical and After-Sales Service department
• STAV contact details: Ribimex, 56 Route de Paris, F-77340 Pontault-Combault.
• Tel : 08 92 35 05 77 (0,34€/min ; only in France)
• email : sav@ribimex.fr
• Internet Website: www.ribimex.com

Documents / Resources

RIBIMEX PRCOMP1-06SILR Air Compressor [pdf] Instruction Manual PRCOMP1-06SILR, PRCOMP1-06SILR Air Compressor, Air Compressor, Compressor

References

• User Manual