Mircom-logo

Mircom MS-710APU Advanced Protocol Intelligent Manual Station

Mircom MS-710APU Advanced Protocol Intelligent Manual Station-fig1

Description

  • Mircom’s MS-710APU Advanced Protocol Intelligent Manual Station is made of a high quality, die-cast metal and is available as a dual-action device with key resets and a permanently attached intelligent module. The intelligent manual station has a pair of rotary decimal switches which allows for two digit address setting. Pulling the handle initiates the operation of the intelligent module.
  • The manual station is available with CAT-30 keys and mounts on a standard single gang backbox, Mircom model BB-700 interior surface metal backbox, or BB-700WP weather proof backbox.
  • Mircom’s Advanced Protocol (AP) devices use a high speed communication protocol that greatly increases the speed of communication between the intelligent devices. Mircom’s Advanced Protocol uses a superior group polling method as well as an interrupt feature that provide for a faster response to an alarm condition. In addition, the Advanced Protocol allows for greater system capacity with support for up to 318 devices per SLC circuit. The AP devices are backwards compatible to operate in CLIP mode for legacy system applications.

Features

  • Dual Action
  • Key resettable
  • Permanently attached Intelligent Addressable Module
  • Rotary switches for direct-dial entry of address.Each unit can have address set for 01-159 for Advanced Protocol mode and 01-99 for CLIP mode
  • High-gloss red enamel finish
  • Plastic breakrod
  • Meets ADA 5 lb. maximum manual-force
  • Mounts on standard single gang box, Mircom’s BB-700 surface metal backbox or BB-700WP weather proof backbox

Operation

The MS-710APU Dual Action Intelligent Manual Station is operated by pushing the bar labelled “PUSH BAR” and then pulling down the handle marked “PULL HANDLE”. The MS-710APU is reset by opening the station with the key, placing the handle in the normal upright position and re-locking the station.

Specifications

The manual station shall be Mircom’s MS-710APU. Operating instructions shall be in raised English lettering and the unit shall be constructed of high quality die-cast metal and finished in red enamel paint to provide quick identification. Pulling the handle shall initiate immediate operation of the intelligent addressable module. All manual fire alarm stations shall be installed as per the specific requirements outlined in the UL codes, as well as all other applicable national or local codes. Final acceptance is subject to the local authority having jurisdiction.

NOT TO BE USED FOR INSTALLATION PURPOSES.
THIS INFORMATION IS FOR MARKETING PURPOSES ONLY AND NOT INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY.

Specifications

Dimensions4.93” H x 3.56” W x 2.9” D
Nominal Operating Voltage15–32 VDC
Maximum Alarm Current @ 24V600 μA
Average Operating Current @ 24V400 μA

Surface Mount Backboxes

Mircom MS-710APU Advanced Protocol Intelligent Manual Station-fig2

Wiring Diagram

Mircom MS-710APU Advanced Protocol Intelligent Manual Station-fig3

Mounting Diagram

Mircom MS-710APU Advanced Protocol Intelligent Manual Station-fig4

Ordering Information

ModelDescription
MS-710APUAdvanced Protocol Intelligent Key Resettable Dual Action Manual Station
BB-700Series 700 Interior Surface Mount Backbox, Red Finish
BB-700WPSeries 700 Weatherproof Surface Mount Backbox, Red Finish
GL-007KActivation indicator (plastic break bar)

THIS INFORMATION IS FOR MARKETING PURPOSES ONLY AND
NOT INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY.
For complete and accurate technical information relating to performance, installation, testing and certification, refer to technical literature. This document contains intellectual property of Mircom. The information is subject to change by Mircom without notice. Mircom does not represent or warrant correctness or completeness. All rights reserved. All other trademarks and registered trademarks are properties of their respective owners.

Canada
25 Interchange Way Vaughan, ON L4K 5W3 Telephone: 905-660-4655 | Fax: 905-660-4113

U.S.A.
4575 Witmer Industrial Estates Niagara Falls, NY 14305 Toll Free: 888-660-4655 | Fax Toll Free: 888-660-4113
www.mircom.com

firealarmresources.com

Documents / Resources

Mircom MS-710APU Advanced Protocol Intelligent Manual Station [pdf] Instruction Manual
MS-710APU Advanced Protocol Intelligent Manual Station, MS-710APU, Advanced Protocol Intelligent Manual Station, Protocol Intelligent Manual Station, Intelligent Manual Station, Manual Station, Station

References

Leave a comment

Your email address will not be published. Required fields are marked *