MICROTECH-LOGO

MICROTECH CALIPER IP67 Long Jaw Digital

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-PRODUCT

SPECIFICATION

EXTRA LONG jaw caliper IP67

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (1)

WIRELESS EXTRA LONG jaw caliper IP67

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- 12

BUTTON FUNCTIONS

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (3)

SET – Functions setting: PRESET, LIMITS, UNITS, MIN/MAX
MODE – Favorite key to one of the most used function

0 – Setting 0, PRESET value

ONLY WIRELESS MODIFICATION

DATA – Switch on WIRELESS module/data transfer

BATTERY REPLACEMENT

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (4)

CR2032 BATTERY (3V)

POWER CONSUMPTION

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (5)

OPERATION INSTRUCTIONS

Wipe with a clean cloth, soaked in gasoline, measuring surface of the frame and gauge calipers to remove anti-corrosion oil. Then wipe them with a clean dry cloth.
If necessary, open the battery cover; insert the battery (type CR2032) according to the polarity of the electrodes.

This caliper has Autoswitch on/ off function:

  • move electronic module for switch on caliper
  • after 10 minutes without any moving caliper will switch off
    • During the measurement, measuring jaws should to sum to the measured object without knocking.
    • During the measurement avoid warps of measuring surfaces of the instrument.
    • Measuring surface must be fully in contact with the measurement object

FORCE CONTROL

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (6)

ONLY FORCE MODIFICATION

  • Check the ZERO SETTING of the caliper. Sum the measuring jaws to contact with each other. Force is generated with a measuring force. Push Force module to create the recommended force (10-15N) by the block adjustment and press ZERO button.
  • During the measurement, measuring jaws should to sum to the measured object without knocking.
  • During the measurement avoid warps of measuring surfaces of the instrument. Measuring surface must be fully in contact with the measurement object.
  • Optimal measuring force for this size caliper 10-15N (depend on jaw lenght). During a measuring process use Force module to improve repeatability.

WARNING!

IN THE PROCESS OF WORKING WITH CALIPERS SHOULD BE AVOIDED:
Scratches on the measuring surfaces;
Measuring the size of object in the process of machining;
Shocks or dropping, avoid bending of rod or other surfaces.

WIRELESS DATA TRANSFER MODES

ONLY WIRELESS MODIFICATION

MICROTECH caliper with Built-in Wireless data output module for transfer results

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (7)

DOWNLOAD APP

DOWNLOAD MDS APP FOR MICROTECH DEVICES
WIRELESS CONNECTION FROM www.microtech.ua,
GooglePlay & App Store

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (8)

WIRELESS DATA TRANSFER CONNECTION

ONLY WIRELESS MODIFICATION

WIRELESS TO MDS APP CONNECTION

To switch between WIRELESS modes (WIRELESS, HID, and HID + MAC), press and hold the data transmission button for 5 Seconds. 5 sec;

  • In WIRELESS TO MDS MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- 13 non-stop blinking on display up to connection to MDS app and selecting STANDARD or ECO sub-mode.
  • In STANDARD submode data transfer 4 times/sec and MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- 13 all time on display. Push DATA button to save data to MDS app or use buttons and Timer inside app.
  • In ECO (GATT) submode caliper ready to transfer data any time with no indication. Push DATA button to save data on MDS app.
  • For selecting next mode push DATA button 5 sec.
  • ECO recomended for battery economy !!!

WIRELESS HID CONNECTION
To switch between wireless modes (WIRELESS, HID, and HID + MAC), press and hold the data transmission button for 5 Seconds.

By default, digital wireless devices start in WIRELESS mode, which is indicated by a constantly blinking wireless icon on the display. When you hold the button for 5 Seconds for the first time, WIRELESS mode is activated.
Press and hold the button again for 5 Seconds to switch to HID mode. After a third press and hold for 5 Seconds, the device will enter HID + MAC mode.
You can easily identify the current mode by searching for Bluetooth devices, where the device name will indicate the mode, either MICROTECH HID or MICROTECH HID + MAC.

NOTICE:
Always remember to disconnect and remove the device from your Bluetooth settings before changing modes to avoid conflicts and ensure a smooth transition.

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (9)

INDUSTRY 4.0 INSTRUMENTS

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (10)

MICROTECH-CALIPER-IP67-Long-Jaw-Digital-FIG- (11)

Change without prior notice

MICROTECH
innovative measuring instruments
61001, Kharkiv, Ukraine, str. Rustaveli, 39
tel.: +38 (057) 739-03-50
www.microtech.ua
tool@microtech.ua

Documents / Resources

MICROTECH CALIPER IP67 Long Jaw Digital [pdf] User Manual
142408445, 142408444, 142411445, 142411444, 142418445, 142418444, 142418464, 142120144, 142120164, 142120104, 142125144, 142125164, 142125104, 142130144, 142130164, 142130104, 142135144, 142135164, 142135104, CALIPER IP67 Long Jaw Digital, CALIPER IP67, Long Jaw Digital, Jaw Digital, Digital

References

Leave a comment

Your email address will not be published. Required fields are marked *