iLive ISB309B Wireless Tailgate Speaker
Important Safety Instructions
- Read these Instructions.
- Keep these Instructions.
- Heed all Warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding – type plug. A Polarized plug has two blades with one wider than the other. A grounding type Plug has two blades and a third grounding prong. The wide blade or the third Prong is provided for your safety. When the provided plug does not fit into Your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, Convenience receptacles and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over
FCC Warnings
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings and Precautions
- CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
- Mains plug is used as disconnect device and it should remain re adily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
- WARNING: Shock hazard – Do Not Open.
- CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
- WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- WARNING: Do not place this unit directly onto furniture surfaces with any type of soft, porous, or sensitive finish. As with any rubber compound made with oils, the feet could cause marks or staining where the feet reside. We recommend using a protective barrier such as a cloth or a piece of glass between the unit and the surface to reduce the risk of damage and/or staining.
- WARNING: Do not ingest battery, chemical burn hazard.
- Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
- Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed of according to state and local guidelines. They should never be disposed of in normal household waste and they should never be incinerated, as they might explode. Contact your local government for disposal or recycling practices in your area.
WARNING: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer. For more information go to: www.P65Warnings. ca.gov This product meets and complies with all Federal regulations.
Features
- Bluetooth wireless – range 60 ft.
- Voice prompts announce speaker functions
- Single 6.5” speaker
- Digital FM radio
- Microphone input
- 5mm Aux In
- USB port – supports MP3 file format
- Built-in rechargeable battery
- Battery life: approx. 3 hrs. playtime
Includes
- USB cable for battery recharge
Overview
Control Panel
- Carry Handle
- Phone Rest
- Volume: Turn to adjust the volume.
Press and hold to power the speaker ON or OFF. Press to change play mode: Bluetooth/Aux/FM.
Press and hold to begin pairing to a Bluetooth device (BLUETOOTH). Press to play or pause tracks (BLUETOOTH, USB). Press twice to turn the LED lights ON or OFF.
Short press to skip audio tracks (BLUETOOTH/USB) or radio presets (FM). Press and hold to adjust microphone echo effect when a microphone is connecte.- Carry Strap Attachment Points: Located on both sides of the speaker (carry strap not included).
- DC Power Input & Charging LED: Use to charge the internal battery and power the speaker. The LED will shine solid red when charging, and turn off when fully charged.
- USB Media Port: Play media from a USB drive.
- Microphone Jack (1/4˝ input): When in use, the microphones will always be heard, regardless of the source input.
- Reset Button
- Aux in (3.5mm Audio Input)
Charging the Battery
To power the unit or charge the internal battery, plug the USB charging cable into the DC Power Input on the speaker and a powered on computer or USB power adapter (not included) and standard power outlet. Battery life is approximately 3 hours.
USB
- Load a USB drive into the USB Media port. The speaker will automatically switch to USB Mode, indicated by a voice prompt. You can also press the Source button to switch to USB Mode manually.
- Use the controls on the speaker to select and play audio from the connected drive.
Bluetooth Wireless
Pairing & Playing Audio
After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to a reset of the device. If your device should become unpaired or you find it is unable to connect, repeat the steps listed here.
- Press the button to select Bluetooth Mode, indicated by the voice prompt “Bluetooth”.
- Press and hold the button to enter pairing mode, indicated by the voice prompt “Bluetooth is connecting.” The speaker will now be discoverable by your Bluetooth device.
- On your Bluetooth device, scan for and select ISB309 in your Bluetooth settings to pair. If your device requests a password, enter the default password 0 0 0 0 . Refer to the user’s manual for your specific device for instructions on pairing and connecting Bluetooth devices.
- When successfully paired, the voice prompt will say “Bluetooth connected. “Use the controls on your connected device to select and begin playing audio. Use the controls on the speaker or the connected device to play, pause, and adjust volume.
Aux In
Requires a 3.5mm audio cable (not included).
- Connect a 3.5mm audio cable to the Aux In on the unit and the audio output/ headphone jack on an audio device.
- Press Source to switch to Aux Mode.
- Use the controls on the connected device to select and play audio. Be sure the volume on your connected device is audible when you begin playing.
FM Radio
Radio Reception
An FM receiver is built into the speaker. Adjust the position of the speaker to improve FM radio reception.
Radio Tuning and Saving Station Presets
- Press the button to select FM Radio Mode, this will be indicated by a voice prompt.
- Press and hold the button to scan and save radio stations automatically.
- Press the buttons to cycle through saved radio stations. Press and hold to manually search through FM radio frequencies.
Microphone
Requires a microphone with a 1/4˝ audio cable or 1/4˝ adapter (not included).
- Connect a microphone to the Microphone Input on the unit. The speaker will play audio from the microphone as long as it is connected.
- Use the Volume Dial to adjust the overall volume of the speaker and microphone. Press and hold the buttons to adjust the echo effect of the microphone
Customer Support
To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at: www.iLiveElectronics.com
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com
Customer Service: 1-888-999-4215 | Email Support: prodinfo@dpiinc.com | Email Parts: partsinfo@dpiinc.com
Copyright 2018 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners.
Specifications are subject to change without notice.
FAQs
How should an ILive tailgate speaker be charged? To power the device or recharge its internal battery, affix the USB charging cable to it. power outlet and adapter types (not included). About three hours are left on the battery.
DC Power Input/Battery Charge LED: Use the input to power the speaker and charge the internal battery. When the battery is charging, the charging LED will flash; after it is fully charged, it will remain solid. 2. USB Power Port: Recharge portable electronics like tablets and cellphones.
Connect the USB charging cord to the DC Power Input on the speaker, a running computer or USB power adapter (not included), and a regular power outlet to charge the internal battery. The average charging time is four hours. At 50% volume, the battery lasts about 18 hours.
This speaker is made to provide listeners with the strength (5W) and quality they desire along with the simple Bluetooth audio transfer at an incredible price. A: No, the speakers’ lights will erratically flash when music is playing.
whitish noise Turning the speaker ON and OFF again Speaker is still not working correctly. To return to factory settings, depress the Alexa Mute button for 10 seconds. Visit www.iLiveElectronics.com for warranty information and the most recent version of this user manual.
When turned on, the speaker will be in Bluetooth mode. Scan for and choose in your Bluetooth settings by using your Bluetooth device’s controls. The pairing signal will turn solid and a voice will proclaim the connection after it has been successfully established.
Press “Add Device” while the iLive Wi-Fi app is open. To enter the appropriate information, hold down the Pair (WPS) button on the speaker while doing so. 2. As the app sets up the speaker and your Wi-Fi network, it will update you on its progress.
The 2020 GMC Sierra Heavy Duty will soon be able to purchase the MultiPro Tailgate with the MultiPro Audio System by KICKER, which is already available on the 2019 and 2020 GMC Sierra 1500 models.
If your Bluetooth devices aren’t connecting, they probably aren’t in pairing mode or are out of range. Try rebooting your devices or letting your phone or tablet “forget” the connection if you’re experiencing persistent Bluetooth connection issues.
Make sure Bluetooth is activated. Find out the pairing method your device uses. activate discoverable mode. Ensure that the two devices are sufficiently close to one another. Turn the gadgets on and off again. Eliminate previous Bluetooth connections.
Make sure your TV is on and that you have an HDMI cable before you connect your iLive to your TV. Locate your TV’s HDMI input next. After locating it, attach the HDMI cable’s one end to the HDMI input on your TV and the other end to the HDMI output on your iLive.
Verify that the speaker’s power wire and audio out cord are firmly plugged in and are not torn or frayed. If they are, you should, if you are able to, carefully solder the wires back together. If not, you’ll probably need to have the device’s speakers replaced.
Hold the Power button down for nine seconds to turn the device on and start pairing. At that point, a voice will say “Bluetooth is connecting,” and the indicator will start rapidly flashing blue. When pairing, stay 3 feet or less away from the device. Select in the Bluetooth Settings to pair using the controls on your Bluetooth device.
This portable small tailgate speaker is designed to disseminate sound and will become your go-to for tailgates and parties alike. The 6 hour battery life (rechargeable) and captivating LED light effects make this tailgate speaker a need.
Press to choose between Bluetooth, Aux, USB, and Micro SD/TF source modes. To turn LED lights ON/OFF, press and hold.
