Astaanta Honeywell

H-Class - logo

HD Peel & Present Option

Honeywell OPT78-2627 H-Class Powered Internal Rewind Option - detamexxaq by macaamiisha our.

Honeywell OPT78-2613-04 H-Class Thermal Transfer Option

In ka badanview

This document describes the contents, installation, and use of the Heavy Duty Peel and Present option for the H-Class printer. After verifying the contents of the kit and the tools needed, follow the steps below to install and begin using the option. A maintenance procedure is also included, so keep this documentation for future reference.

Digniin TAXADIR
For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.

Contents of the Heavy Duty Peel and Present Option

Qalabkani waxa uu ka kooban yahay shaygan soo socda:
• Heavy Duty Peel and Present Assembly

Honeywell H-4310 H-Class HD Peel and Present Option - Heavy Duty Peel and PresentQalabka Loo Baahan Yahay
Si aad u rakibto doorashadan, waxaad u baahan doontaa kaashawiito caadiga ah.

Tallaabada 1: Diyaarinta Printer-ka

A) Dami 'Dami' Awoodda Awooda oo xadhigga korontada ka saar Qalabka AC.

Honeywell H-4310 H-Class HD Peel and Present Option - Preparing the Printer

B) Hoos u riix Qabsado, ka dibna horay u soo jiid si aad meesha uga saarto Albaabka

Honeywell H-4310 H-Class HD Peel and Present Option - DoorC) Kordhi Daboolka Helitaanka oo ka saar warbaahintaada daabacaha.

Honeywell H-4310 H-Class HD Peel and Present Option - Access Cover

D) Ka saar meesha suulka iyo Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)

Step 2: Installing the Heavy Duty Peel and Present Assembly

A) Riix barta Latch oo furo Peel and Present Golaha.

Honeywell H-4310 H-Class HD Peel and Present Option - Present Assembly

B) Si taxadar leh u cadaadi Peel and Present Assembly galay Front Plate Connector.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present

C) Adkee Ku sii kordhaya si loo sugo amniga Peel and Present Assembly ilaa daabacaha.

Tallaabada 3: Isticmaalka Xulashada
Inta lagu jiro hawlgalka, calaamaduhu waa laga tirtiri doonaa alaabta gadaal ka riixaya oo lagu bixin doonaa "dalabka" - taas oo ah, daabacaadda xigta waxay dhici doontaa kaliya ka dib marka calaamad hore loo daabacay laga saaro daabacaha. Xusuusin ahaan, "KA SAAR LABELKA" waa la soo bandhigi doonaa si ay kuu soo jeediso marka calaamaduhu sugto saarista.

Ku bilow adeegsiga ikhtiyaarka sida soo socota:

A) load warbaahinta (fiiri faahfaahinta Buugga Hawl-wadeenka). Kordhi 20 inji (50 cm) oo ah warbaahinta ka daabacaadda.

Honeywell H-4310 H-Class HD Peel and Present Option - Media

B) Ka saar summada qaybtan la dheereeyey ee warbaahinta, ka tag oo keliya Qalabka Taageerada. Samee cidhifka hore ee kan BackingMaterial.
C)
Jidka Qalabka Taageerada hoos Caawin Roller iyo Internal Rewinder.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing

D) Duub Qalabka Taageerada jihada saacada ka soo horjeeda ee agagaarka Dib-u-celinta Hub and insert the creased leading edge into one of its Slots. Insert the Isku dhafka Warbaahinta (Item 6) into the Slot over the creased leading edge of the Taageerida Material and around the Rewinder Hub.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing Material

E) Xiritaan Peel and Present Assembly. Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present Assembly

F) Xaqiiji taas DIYAAR is displayed on the Front Panel then press the Furaha FEED oo u soco sida ay kuu arkaan:

  • If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
  • If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”

Honeywell H-4310 H-Class HD Peel and Present Option - Front Panel

Notes:

  1. Hawlgalka Sensor Present ee ikhtiyaarkan sidoo kale waxaa lagu xakameyn karaa amarada software-ka martida loo yahay, markaa hubi in barnaamijka calaamadaynta si habboon loo habeeyey si loogu isticmaalo marka loo dirayo qaababka summada daabacaha.
  2. Haddii doorashadan meesha laga saaro iyadoo la adeegsanayo awood, daabacuhu wuxuu u dhaqmi doonaa sidii calaamad sugaysa saarista; si loo soo celiyo hawlgalka caadiga ah, wareegga awoodda printer ah.

Tallaabada 4: Habaynta Printer-ka

While the Heavy Duty Peel and Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:

Fiiro gaar ah: Habka soo socda, kala tasho Buugga Hawl-wadeenka si aad u hesho tilmaamo faahfaahsan oo faahfaahsan.

A) Riix barta MENU Button on the printer’s front panel.
B) Isticmaalka DOWN Button, scroll to Ikhtiyaarada Daabacaada then press the Right Button.
C) Isticmaalka DOWN Button, scroll to Dareemiyaha xaadirka ah ka dib riix Gali Furaha.
D) Isticmaalka DOWN Button, scroll to HORDHAC ka dib riix Gali Furaha.
E) Isticmaalka DOWN Button, scroll to JIRADA ka dib riix GELIN Fure
F) Riix barta KA BAX Key then, at the BADBAADO ISBEDELADA? degdeg ah, dooro HAA si loo dhammaystiro rakibidda.
G) Turn the Power Switch 'Dami' iyo ‘On’ to reset the printer and complete the configuration.

Fiiro gaar ah: If the printer fails to separate the labels from the backing material, and the Internal Rewinder is not turning, it may need to be enabled. Using the procedure above as a guide, press the MENU Button, scroll to PRINTER OPTIONS, ka dibna u REWINDER, dooro AUTO Afterward, press the KA BAX key and save your changes when prompted.

Maintaining the Heavy Duty Peel & Present Assembly

To ensure trouble-free operation, the Heavy Duty Peel and Present Assembly should be cleaned after every 100,000 inches (254,000 cm) of media use. This interval depends on the label adhesive, where “gummy” adhesives may require more frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS → MEDIA COUNTERS in the printer’s menu system.)

Clean the assembly as follows:

  1. Dami 'Dami' Dab-damiska oo ka saar xadhigga korantada ee AC Receptacle. Kor u qaad daboolka gelitaanka oo ka saar warbaahinta daabacaha.
  2. Remove the Peel & Present Assembly from the printer.
  3. Isticmaalka hawo ciriiri ah ama burush jilicsan, nadiifi dareemayaal on the assembly.Honeywell H-4310 H-Class HD Peel and Present Option - SensorsFiiro gaar ah: Nadiifinta kaydka culus, khamriga isopropyl waa la isticmaali karaa - waa haddii si taxadar leh loo mariyo iyadoo la isticmaalayo suuf suuf ah, ka dibna loo oggolaado in la qalajiyo ka hor inta aan dib loogu xidhin ikhtiyaarka daabacaha.
  4. Riix barta Latch to open the Peel and Present Assembly. Then remove the C-Clip that secures the Upper Roller Shaft si ay u Front Cover.Honeywell H-4310 H-Class HD Peel and Present Option - Front Cover
  5. Remove the Upper Roller Shaft and the associated Rollers.Honeywell H-4310 H-Class HD Peel and Present Option - Rollers
  6. Isticmaal a Cudur Swab dampened with alcohol, wipe all rullaluistemadka iyo Upper Roller Shaft surface clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
    Fiiro gaar ah: For cleaning heavy deposits from the Rollers and Shafts in the following steps, WD-40 or another non-damaging adhesive remover can be substituted for isopropyl alcohol – provided this adhesive remover is carefully applied using a cotton swab.
  7. Muuji Rollers dib u gal ah Upper Roller Shaft, place the components into the Front Cover, and reinstall the C-Clip.
  8. murugeeysan iyo wiish labada ILAALI in sugaan Lower Roller Assembly to the Front Cover (as shown) and then, while keeping it intact, carefully remove the entire Lower Roller Assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Tabs
  9. Take note of the individual rullaluistemadka positions – they must be reinstalled in the same order – then, carefully remove the Rollers ka Lower Roller Shaft.Honeywell H-4310 H-Class HD Peel and Present Option - Lower Roller Shaf
  10. Isticmaal a Cudur Swab dampened with alcohol, wipe all rullaluistemadka iyo Lower Roller Shaft surfaces clean. Pay special attention to the ridges on the Rollers to ensure that they are clean.
  11. Muuji Rollers, in their original order, onto the Lower Roller Shaft and reinstall them in the Front Cover, hubinta in ILAALI are properly seated. Reinstall the Peel and Present Assembly onto the printer to complete the cleaning procedure.

Dukumentiyada / Kheyraadka

Honeywell H-4310 H-Class HD Peel and Present Option [pdf] Tilmaamaha
H-4310, H-Class, HD Peel and Present Option, H-4310 H-Class HD Peel and Present Option

Leave a comment

cinwaanka email Your aan laga soo saari doonaa.