Go Power GP-MPPT-PRO-40-60-R MPPT Pro Controller Remote
SOLAR CONTROLLER REMOTE
| Communication Fault Indicator | 5 | Down Button | |
| 2 | Communication Connection Indicator | 6 | Escape Button |
| 3 | LCD Screen | 7 | OK Button |
| 4 | Up Button | ||
MAIN MENU 
ICON DESCRIPTION
 | Steady on | Nighttime |
Related to charging |
 | Steady on | Daytime | |
 | Steady on | A dynamic arrow indicates charging is in process, while a static one indicates otherwise. | |
 | “Oto 100%” | Current battery capacity | Related to battery |
| “0%” in slow | Battery over-discharged | ||
| flashing “100%” in quick flashing | Battery over-voltage | ||
 | Steady on | A bulb shown as left and a dynamic arrow indicate the load is switched on. |
Related to load |
 | Steady on | A bulb shown as left and a static arrow indicate the load is switched off. | |
 | Quick flashing | Overload or short-circuit protection | |
TO SET BATTERY TYPE, VIEW HISTORICAL DATA, AND USE OTHER FUNCTIONS, REFER TO THE USER MANUAL FOR AT GPELECTRIC.COM/MPPT-PRO.
INSTALLATION
The GP-MPPT-PRO-40-60-R installation on a controller case or panel. External dimensions: 115.82 x 115.82mm Installation dimensions: 96mm or 103.82×103.82mm Installation hole diameter: ¢ 3.5 (mm)
The GP-MPPT-PRO-40-60-R installation on a Wall. External dimensions: 118.5 x 118.5x48mm Installation dimensions: 50x50mm or 70x70mm Installation hole diameter: ¢ 5 (mm)
The product design features 4 keys which, from left to right, are: They equal to (“Up”, “Down”, “ESC”, “OK”)
KEY I OPERATION
DESCRIPTION
| Up | Tap, press and hold | 1) When browsing a menu , tap the key for a page up, 2) In parameter setting, tap the key to increase the value by a minimum unit; 3) Press and hold the key for quick page -up movement or value increasing. |
| Down | Tap, press and hold | 1) When browsing a menu , tap the key for a page down; 2) In parameter setting, tap the key to decrease the value by a minimum unit; 3) Press and hold the key for quick page-down movement or value decreasing. |
|
ESC |
Tap | 1) When browsing a menu, tap the key to return to the previous level, until the main menu is reached; 2) In the setting mode, a tap on this key can cancel the data modification in process and exit the setting mode. |
| Ok
| Tap | 1) In a menu which contains submenus, tap the key to enter into a submenu; 2) In a menu with settable or adjustable parameters, tap the key to enter into or confirm parameter setting. |
|
Press and hold | If “manual mode” is selected as the load mode, a press-and-hold on the key to switch on/ off the load. If it’s not in the manual mode, a press-and-hold will cause the display to skip to the load mode setting interface as a reminder. (No te; if no load is co nnecte d to the co ntroller , this funct io n and related lo ad parameters will become inoperative.) |
PACKING LIST
| ITEM | QTY | REMARKS |
| LCD Display Unit | ||
| Data Cable (25ft) | 6 cores, RJ12 at both ends | |
| KA3 * 12 Black Countersunk Machine Screws | 4 | For installation on a panel |
| KA4 * 25mm Tapping Screws | 4 | For installation on a wall |
| M6 * 25mm Plastic Expansion Bolts | 4 |
Find tech tips, manuals and support at gpelectric.com
Documents / Resources
 | Go Power GP-MPPT-PRO-40-60-R MPPT Pro Controller Remote [pdf] User Guide GP-MPPT-PRO-40-60-R, MPPT Pro Controller Remote |
