TH99 RGB Mechanical Keyboard

EPOMAKER TH99

1800 Compact Hot-swappable RGB Mechanical Keyboard with Numpad

Should you require more assistance please email us at support@epomaker.com

BASIC FUNCTION

Function Key Combinations

Fn + Esc (Hold 5s) Reset the keyboard
Fn + R Long press to pair Device BT1; short press to change to Device Bt1
Fn + Q Long press to pair Device BT2; short press to change to Device Bt2
Fn + W Long press to pair Device BT3; short press to change to Device Bt3
Fn + E Long press to pair Device BT3; short press to change to Device Bt3
Fn + Enter Battery Check

Lights

Fn + Backspace Turn on/off Backlights
Fn + Insert Turn on/off Backlights
Fn + Del Toggle Backlight Effect
Fn + ↑ Toggle Backlight Color
Fn + ↓ Backlight Brightness +
Fn + ← Backlight Brightness –
Fn + → Backlight Speed –

PAIRING BLUETOOTH

Toggle the switch to the BT side, make sure that the keyboard is under the Bluetooth mode:

1. Hold Fn+Q/W/E for 3-5 seconds till the indicator flashes fast, the keyboard is
   ready to pair.
2. Turn on your Bluetooth device and find “TH99 BT-1”, “TH99 BT-2”, “TH99 BT-3”,
   then connect. When the keyboard is connected to the Bluetooth device, the
   indicator stops flashing and the connection is done.
3. Press Fn+ Q/W/E to toggle between the Bluetooth devices 1/2/3.

PAIRING WIRELESS 2.4GHz

Toggle the switch to the 2.4G side, make sure that the keyboard is under the 2.4G wireless mode:

1. Hold Fn+R for 3-5 seconds till the indicator flashes fast, the keyboard is ready to pair.
2. Insert the 2.4G dongle to your computer. When the keyboard is connected,
   the indicator stops flashing.

Wired Mode

Toggle the switch to the middle and plug the keyboard.

Note: The battery charges when the keyboard is plugged. Red light is on for 10s when charging.

Battery Check

Hold Fn + Enter, the keys from 1 to 0 lights up to show the battery percentage; for
example, if the keys from 1 to 6 light up when holding Fn + Enter, it means that the
battery life is currently 60%; if keys of 1-0light up, battery life is 100%.

Indicator

Win Lock: Press Fn+Win key to lock the Win key, and the key lights up. Press Fn +
Win again to release the key and the light off.

Capslock: Press Capslock to lock the Capital letters and the Capslock key lights
up. Press Capslock again to release the key and the light off.

Numlock: Press Numlock to lock the Numpad to the secondary layer and Num
key lights up. Press Numlock again to release the numpad and the light off.

Spacebar: Red light is on for 10s when charging. Red light blinks when the
battery is low.

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth
vertically (on the Y-Axis) at the center of the switch, as shown in
the example graphic above.

2. Grab the switch with the Switch Puller and apply pressure until
the switch releases itself from the plate.

3. Using firm but gentle force pull the switch away from the
keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.

2. Align the switch vertically to have the Gateron logo facing north. The
pins should align themselves to the keyboard PBC.

3. Press the switch down until you hear a click. This means your switch
clips have attached themselves to the keyboard plate.

4, Inspect the switch to ensure it’s properly attached to your keyboard,
and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.

Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing
keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid
damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, lease emt to
support@epomaker.com with your purchase order number and
2 detailed description of your issue.

We normally respond to enquires within 24 hours you
purchased your keyboard from acistributor or not from any
official store of Demomaker, lease contact them correctly for any
2ckitional hele.

COMMUNITY FORUMS

Join our community and learn together with
other keyboard enthusiasts.

WARRANTY

EPOMAKER’s Warranty covers any factory defects that might
affect the proper functionality of your purchase. It doesn’t
cover any damage that may occur from normal wear and tear.
If your product is defective we will send you a replacement
unit. Replacement units might require you to send the
defective unit back to Epomaker.

We provide a 1 year warranty for our products when bought
from our website (EPOMAKER.com). Your item will not be
covered by your 1 year warranty if the inspection shows any
sign of modification or changes unsupported by the original
product, these include: Changing internal components,
Assembling and reassembling the product, Replacing
Batteries, etc.

We will ONLY cover the item if it is bought from our official
stores. You do not have a warranty with us if you bought the
item from another reseller or likewise. Please contact the store
that you bought your product from to resolveiissues.

Documents / Resources

EPOMAKER TH99 RGB Mechanical Keyboard [pdf] User Guide TH99 RGB Mechanical Keyboard, TH99, RGB Mechanical Keyboard, Mechanical Keyboard, Keyboard

References

• User Manual