BAFANG DP C220.CAN Display

IMPORTANT NOTICE

• If the error information from the display cannot be corrected according to the instructions, please contact your retailer.
• The product is designed to be waterproof. It is highly recommended to avoid submerging the display under water.
• Do not clean the display with a steam jet, high-pressure cleaner or water hose.
• Please use this product with care.
• Do not use thinners or other solvents to clean the display. Such substances can damage the surfaces.
• Warranty is not included due to wear and normal use and aging.

INTRODUCTION OF DISPLAY

• Model: DP C220.CAN BUS
• The housing material is ABS and Acrylic.
  
• The label marking is as follows
  

Note: Please keep the QR code label attached to the display cable. The information from the Label is used for a later possible software update.

PRODUCT DESCRIPTION

Specifications

• Operating temperature: -20℃~45℃
• Storage temperature: -20℃~50℃
• Waterproof: IPX5
• Storage room Humidity: 30%-70% RH

Functional Overview

• Speed display (including top speed and average speed, switching between km and miles)
• Battery capacity indicator
• Lighting control
• Brightness setting for backlight
• Walk assistance
• Indication of performance support
• Motor output power indicator
• Time display for single journeys
• Kilometer stand (including single-trip distance, total distance and remaining distance)
• Setting the support levels
• Energy consumption indicator CALORIES (Note: If the display has this function)
• Display for the remaining distance (Depends on your riding style)
• Information View (battery, controller, HMI and sensor)
• Error messages view

DISPLAY

1. Display of battery capacity in real time.
2. Indicator of support level/walk assistance.
3. The display shows this symbol , When the lights are turned on.
4. Unit of speed
5. Digital speed display
6. Trip: Daily kilometers (TRIP) – Total kilometers (ODO) – Top speed (MAX) – Average speed (AVG) – Rremaining distance (RANGE) – Energy Consumption (CALORIES) – Output power (POWER)- Travel time (TIME).
   Service: Please see the service section
   

KEY DEFINITION

NORMAL OPERATION

Switching the System ON/OFF

Press and hold (>2S) on the display to turn on the system. Press and hold (>2S) again to turn off the system.
If the “automatic shutdown time” is set to 5 minutes (it can be reset with the “Auto Off” function, See “Auto Off”), the display will automatically be turned off within the desired time when it is not in operation. If the password function is enabled, you must enter the correct password to use the system.

Selection of Support Levels

When the display is turned on, press the or button (<0.5S) to switch to the support level, the lowest level is 0, the highest level is 3. When the system is switched on, the support level starts in level 1. There is no support at level 0.

Selection mode

Briefly press the button (<0.5s) to see the different trip modes.
Trip: daily kilometers (TRIP) – total kilometers (ODO) – Maximum speed (MAX) – Average speed (AVG)
– Rremaining distance (RANGE) – Energy consumption (CALORIES) – Output power (POWER) – Travel time (TIME).

Headlights / backlighting

Hold the button (>2S) to activate the headlight and taillights.
Hold the button (>2S) again to turn off the headlight. The brightness of the backlight can be set in the display settings “Brightness”.

Walk Assistance

The Walk assistance can only be activated with a standing pedelec.
Activation: Press the button until this symbol appears. Next press and hold down the button whilst the symbol is displayed, now the Walk assistance will activate. The symbol will blink and the pedelec moves approx. 4.5 km/h. After releasing the button or no button is pressed within 5S, the motor stops automatically and switches back to level 0.

SERVICE

The display shows “SERVICE” as soon as a certain number of kilometers or battery charges has been reached. With a mileage of more than 5000 km (or 100 charge cycles), the “SERVICE” function is displayed on the display. Every 5000 km the display “SERVICE” is displayed every time. This function can be set in the display settings.

Battery capacity indicator

The battery capacity is shown in the top left of the display. Each full bar represents a remaining capacity of the battery in a percentage.
(as shown in the diagram below):

Capacity Range	Indicator
80%-100%
60%-80%
40%-60%
20%-40%
5%-20%
<5%	blinking

SETTINGS

After the display is turned on, press and hold the and buttons (at the same time) to enter into the setting menu, By pressing the or button (<0.5S), you can highlight and select Display Setting, Information or Exit. Then press the button (<0.5S) to confirm your selected option.
Or highlight “EXIT” and press the button (<0.5S) to return to the main menu, or highlight “BACK” and press (<0.5S) the button (<0.5S) to return to the Settings interface.

“Display Setting”

Press the or button (<0.5S) and highlight Display Setting, and then briefly press the button (<0.5S) to access the following selections.

“TRIP Reset” Reset mileage

Press the or button (<0.5S) to highlight “Trip Reset” in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between “YES” or “NO”.
Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the “Display setting”.

“Unit” Selections in km/Miles

Press the or button (<0.5S) to highlight “Unit” in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between “Metric” (kilometer) or “Imperial” (Miles). Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the “Display setting”.

“Brightness” Display brightness

Press the or button (<0.5S) to highlight “Brightness” in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between “100%” / “75%” / “50%” /” 30%”/”10%”. Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the “Display setting”.

“Auto Off” Set Automatic system switch off time

Press the or button (<0.5S) to highlight “Auto Off” in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between “OFF”, “9”/”8″/”7″/”6″/ “5”/ “4”/”3″/”2″/”1″, (The numbers are measured in minutes). Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the “Display setting”.

“Service” Switching the notification on and off

Press the or button (<0.5S) to highlight “Service” in the Display setting menu, and then press button (<0.5S) to select. Then with the or button choose between “NO” or “YES”. Once you have chosen your desired selection, press the button (<0.5S) to save and exit to the “Display setting”.

“Information”

Once the display is turned on, press and hold the and buttons (at the same time) to enter into the setting menu, press the or button (<0.5S) to select “Information”, then press the button (<0.5S) to confirm and enter into “Information”.

Wheel Size

Press the or button (<0.5S) to highlight “Wheel Size”, then press the button (<0.5S) to confirm and view the wheel size. To return, press the button (<0.5S) to exit back to the “Information”.
This information cannot be changed, this is only for information, about the pedelec.

Speed Limit

Press the or button (<0.5S) to highlight “Speed Limit”, then press the button (<0.5S) to confirm and view the speed limit. To return, press the button (<0.5S) to exit back to the “Information”.
This information cannot be changed, this is only for information, about the pedelec.

Battery Information

Press the or button (<0.5S) to highlight “Battery Info”, then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view the contents.
To return, press the button (<0.5S) to exit back to the “Information”.

NOTE: If no data is detected, “–” is displayed.

Controller Information

Press the or button (<0.5S) to highlight “Ctrl Info”, then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version.
To return, press the button (<0.5S) to exit back to the “Information”.

Display Information

Press the or button (<0.5S) to highlight “Display Info”, then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version.
To return, press the button (<0.5S) to exit back to the “Information”.

Torque Information

Press the or button (<0.5S) to highlight “Torque Info”, then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view Hardware Version or Software Version.
To return, press the button (<0.5S) to exit back to the “Information”.

Error Code

Press the or button (<0.5S) to highlight “Error code”, then press the button (<0.5S) to confirm. Now press the or button (<0.5S) to view a list of error codes from the pedelec. It can show information for the last ten errors of the pedelec. The error code “00”means that there is no error.
To return, press the button (<0.5S) to exit back to the “Information”.

ERROR CODE DEFINITION

The display can show the errors of a pedelec. If an error is detected, one of the following error codes will be displayed.
Note: Please read the description of the error code carefully. If you see the error code, restart the system first. If the problem is not resolved, please contact your dealer.

Documents / Resources

BAFANG DP C220.CAN Display [pdf] User Manual DP C220.CAN Display, DP C220.CAN, Display

References

• User Manual