Link: The wallet designed for the internet
TP-Link Community
CE Regulatory Compliance | TP-Linktp-link.com/supportRegulatory Compliance | TP-Linktp-link.com/us/
Installation Guide for tp-link models including: TL-POE160S PoE Injector, TL-POE160S, PoE Injector, Injector
Download für TL-POE160S | TP-Link Deutschland
Mar 24, 2023 — A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE function. A2: Ensure the power consumption of the PD doesn't exceed the maximum.
File Info : application/pdf, 3 Pages, 1.44MB
DocumentDocument© 2023 TP-Link 7106510148 REV1.2.0
Installation Guide
PoEInjector
Note: For simplicity, we will take TL-POE160S for example in this Guide.
Connection
LED Explanation
PWR On: Power on Off: Power off
PoE (Only for TL-POE170S) On: Normal power supply Off: No powered device connected Flashing: Abnormal power supply
Powered Device (PD)
IP Camera
AP
IP Phone
PoE+ Injector
PWR
PWR+DATA OUT DATA IN
Ethernet Device (switch, router, etc.)
Note: 1. The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE AP and PoE IP Phone through an Ethernet cable. 2. For TL-POE170S, plug the product into the wall outlets with earthing connection through the power supply cord.
Specifications
General Specifications
Standards LED
IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at IEEE 802.3bt (Only for TL-POE170S) IEEE 802.3bz (Only for TL-POE260S)
TL-POE160S/TL-POE260S: PWR TL-POE170S: PWR, PoE
Cable Type
10Base-T/100Base-TX: UTP category 5 cable or above (max. 100 m) 1000Base-T/2.5GBase-T: UTP category 5e cable or above (max. 100 m)
Interfaces
TL-POE160S/TL-POE170S 2 × 10Mbps/100Mbps/1Gbps RJ45 Ports TL-POE260S 2 × 10Mbps/100Mbps/1Gbps/2.5Gbps RJ45 Ports
Maximum Power Supply
TL-POE160S/TL-POE260S: 30 W TL-POE170S: 60 W
Dimensions (L×W×H)
Wall Mountable
TL-POE160S/TL-POE260S: 125×59.4×36.8 mm TL-POE170S: 154.7×70×42 mm
Yes
Distance Between
Mounting Holes
TL-POE170S: 102 mm
Environmental and Physical Specifications
Operating Temperature
Storage Temperature Operating Humidity
TL-POE160S/TL-POE260S: 0°C to 40°C (32°F to 104°F) TL-POE170S: 0°C to 45°C (32°F to 113°F)
-40°C to 70°C (-40°F to 158°F)
10% to 90% RH non-condensing
Storage Humidity
5% to 90% RH non-condensing
Safety Information
Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible..
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
FAQ
Q1. Can the PoE injector supply power to a PoE device which doesn't have a gigabit PoE port?
A: Yes. All RJ45 ports of the PoE injector support 10/100/1000 Mbps.
Q2. What can I do if my PoE injector doesn't supply power to the powered device or the supplied power is unstable?
A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE function.
A2: Ensure the power consumption of the PD doesn't exceed the maximum power supply of the PoE injector, otherwise the overload protection of the PoE injector will be activated. The quality and length of the Ethernet cable may influence the reception of the power supply.
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca
FCC compliance information statement
Product Name: PoE Injector Model Number: TL-POE160S/TL-POE170S/TL-POE260S
Responsible party: TP-Link USA Corporation Address: 110 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
Issue Date: 2023.2.22
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
A
VCCI-A Canadian Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 7 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.
BSMI Notice
Pb
Cd
Hg
Cr+6
PBB
PBDE
PCB
1. 0.1 wt %0.01 wt % 2.
Explanation of the symbols on the product label For indoor use only
Alternating current RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
Energy efficiency marking (level VI)
Polarity of d.c. power connector
Class II equipment
Caution
Operator's manual