FOS matekinoroji Razor Laser Multibeam RGB Laser Inofambisa Musoro Mushandisi Manual

FOS technologies Razor Laser Multibeam RGB Laser Moving Head

Kusunungura

Thank you for choosing our products. For your own safety, please read this manual before installing the device. This manual covers important information on installation and applications. Please install and operate the fixture with the following instructions, make sure the power is off before opening the light or repairing it. Meanwhile, please keep this manual well for future needs.

It is made of a new type of high-temperature strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theaters, studios, nightclubs and discos. 6 modules RGB laser light which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation.

Mirayiridzo Yekudzivirira

KUSVIRA!
Ive nekuchengetera nekuita kwako. Ine vol ine ngozitage, you can suffer a dangerous electric shock when touching wires

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this user manual.

Zvichikosha:
Kukuvadzwa kunokonzerwa nekusateererwa kwebhuku rino rekushandisa hakusi pasi pewaranti. Mutengesi haagamuchire mutoro kune chero chinokanganisa kana matambudziko.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore, it is essential that the device be earthed. The electric connection must carry out by a qualified person. The device shall only be used with rate voltage uye frequency. Ita shuwa kuti iripo voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.

Nguva dzose bvisa kubva kune mains, kana mudziyo usiri kushandiswa kana usati wauchenesa. Bata tambo yemagetsi chete neplug. Usafe wakaburitsa plug nekukweva tambo yemagetsi.

During the initial start-up, some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don’t project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

Key Features

• Voltage: AC100-240V,50/60HZ
• Laser color: RGB full color
• Laser simba: 3W
• RGB 500mw*6PCS （R:100mw G:200mw B:200mw） Laser pattern: a variety of rough beam effect patterns.
• Y-Axis rotating: 240°
• Rotation angle: 270°
• Control mode: Music / Automatic / DMX512 (11/26/38CH) Scanning system: stepping motor
• Scanning angle of motor: 25 degrees
• Rated power：<180W
• Working environment: indoor Lamp
• Chigadzirwa chemiitiro: 85 x 16 x 45 cm
• Size of carton case (1in1): 92 x 16 x 32 cm
• N.W: 11kgs / G.W：12.6kgs
• Size of carton case (2in1): 94.5 x 34 x 33.5 cm
• N.W: 23kgs / G.W：26.5kgs

Mashandiro Ekuraira

• The moving head is for laser purposes.
• Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environmental changes. So, make sure to operate the fixture until it is in normal temperature.
• Chiedza ichi chinofanira kuchengetedzwa kure nekuzununguka kwakasimba panguva chero yekufambisa kana kufamba.
• Usakweva mwenje nemusoro chete, kana kuti zvinogona kukonzera kukanganisa kunhengo dzemakanika.
• Usafumure chigadziriso mukupisa, hunyoro kana nharaunda ine huruva yakawandisa paunenge uchiisa. Uye usaisa chero tambo dzemagetsi pasi. Kana kuti zvinogona kukonzera kuvhunduka kwemagetsi kuvanhu.
• Ita shuwa kuti nzvimbo yekuisa iri mune yakanaka chengetedzo mamiriro usati waisa chigadziriso.
• Ita shuwa yekuisa cheni yekuchengetedza uye tarisa kana screws dzakarukwa nemazvo kana uchiisa chigadziriso.
• Make sure the lens is in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
• Ita shuwa kuti chigadziriso chinoshandiswa nevashandi vanokwanisa vanoziva chigadziriso vasati vashandisa.
• Chengetedza mapeji epakutanga kana chero chechipiri chechipiri chichidiwa.
• Usayedze kushandura zvigadziriso pasina kurairwa nemugadziri kana masangano akagadzwa ekugadzirisa.
• Haisi muwaranti yewaranti kana paine chero kusashanda kubva pakusatevera bhuku remushandisi kushanda kana chero mashandiro asiri pamutemo, senge shock short circuit, electronic shock, l.amp akaputsika, etc.

Ratidza menyu control

Press MENU to choose Address / DMX/ Color/ Manual/ Demo /Auto/Sound/ Temp /Version /Hours, then press ENTER to confirm or to enter the next step.if there are more function for options, press UP/DOWN to choose, then press ENTER to confirm, then press MENU to exit, or wait for 10 and exit automatically.

Mashoko:
If no operation on any button, the display will turn off automatically in 20 seconds; if no DMX signal, the first dot of the display will turn on statically, if with DMX signal, the dot will flash

• DMX Address A001
• A512 Address Code
• Channel Mode 11CH, 26CH, 38
• CH channel selection
• Show Mode SOUND AUTO, effect selection
• Slave Mode MASTER, SLAVE, main and auxiliary machine selection
• Black Out YES, NO Standby mode
• Sound State ON, OFF voice switch
• Sound Sense sound sensitivity (0 off, 100 most sensitive)
• Pan Inverse
• YES, NO level reverse
• Tilt1 Inverse YES, NO vertical reverse
• Tilt2 Inverse YES, NO vertical reverse
• Tilt3 Inverse YES, NO vertical reverse
• Tilt4 Inverse YES, NO vertical reverse
• Tilt5 Inverse YES, NO vertical reverse
• Tilt6 Inverse YES, NO vertical reverse
• Back Light ON, OFF backlight switch
• Auto Test Auto Test
• Firmware Version V104 software version number
• Defaults YES, NO Restore factory settings
• System Reset YES, NO Machine reset

DMX Channels 11Channel Mode

CH	basa	DMX Kukosha	Details
1	Pan Motokari	0-255	0-360°positioning
2	Pan Motokari havukavu	0-255	Kubva pakutsanya kusvika pakunonoka
3	Tilt1—Tilt6 motor stroke	0-255	0 no function 1-255 0°-360° positioning
4	Tilt mota havukavu	0-255	Kubva pakutsanya kusvika pakunonoka
5	Kuzvimiririra	0-55	Hapana basa
		56-80	Self-propelled effect 1 (XY uncontrollable)
		81-105 106-130 131-155 156-180	Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
		181-205	Sound control (XY uncontrollable)
		206-230	Self-propelled effect 6 (XY uncontrollable)
		231-255	Sound control (XY uncontrollable)
6	Kuzvimiririra havukavu	0-255	self-propelled speed and Sound-activated sensitivity
7	Dimmer	0-255	0-100% total dimming
8	Strobe	0-9	Hapana strobe
		10-255	Strobe speed kubva kunonoke kusvika kutsanya
9	Laser kushanda	0-15	Hapana basa
		16-27	Mhedzisiro 1
		......	Every time the DMX value is increased by 12, there will be an effect
		232-243	Mhedzisiro 19
		244-255	Mhedzisiro 20
10	Laser kushanda	0-255	self-propelled speed from fast

	havukavu		kunonoka
11	itangezve	0-249	Hapana basa
		250-255	machine reset (value stays for 5 masekondi)

26Channel Mode

CH	basa	DMX Kukosha	Details
1	Pan Motokari	0-255	0-360°positioning
2	Pan Motokari havukavu	0-255	Kubva pakutsanya kusvika pakunonoka
3	Tilt1 motor	0-255	0°-360° positioning
4	Tilt2 motor	0-255	0°-360° positioning
5	Tilt3 motor	0-255	0°-360° positioning
6	Tilt4 motor	0-255	0°-360° positioning
7	Tilt5 motor	0-255	0°-360° positioning
8	Tilt6 motor	0-255	0°-360° positioning
9	Tilt1-Tilt6 motokari	0-255	0 no function     1-255 0°-360° positioning
10	Tilt mota havukavu	0-255	speed from fast to slow
11	Kuzvimiririra	0-55	Hapana basa
		56-80	Self-propelled effect 1 (XY uncontrollable)
		81-105 106-130 131-155 156-180	Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
		181-205	Sound control (XY uncontrollable)
		206-230	Self-propelled effect 6 (XY uncontrollable)
		231-255	Sound control (XY uncontrollable)
12	Kuzvimiririra havukavu	0-255	self-propelled speed and Sound-activated sensitivity
13	Dimmer	0-255	0-100% total dimming
14	Strobe	0-9	Hapana strobe
		10-255	Strobe speed kubva kunonoke kusvika kutsanya
15	Red laser 1-6 kudzikira	0-255	0 hapana basa 1-255 1-100% dimming
16	Green laser 1-6 dimming	0-255	0 hapana basa 1-255 1-100% dimming

17	Blue laser 1-6 kudzikira	0-255	0 no function       1-255 1-100% kudzikira
18	The first group of RGB lasers	0-31	Off
		32-63	Tsvuku
		64-95	Girinhi
		96-127	Bhuruu
		128-159	Yero
		160-191	Pepuru
		192-223	Cyan
		224-255	Yakazara kupenya
19	The second group of RGB lasers	0-31	Off
		31-63	Tsvuku
		64-95	Girinhi
		96-127	Bhuruu
		128-159	Yero
		160-191	Pepuru
		192-223	Cyan
		224-255	Yakazara kupenya
20	The third group of RGB lasers	0-31	Off
		32-63	Tsvuku
		64-95	Girinhi
		96-127	Bhuruu
		128-159	Yero
		160-191	Pepuru
		192-223	Cyan
		224-255	Yakazara kupenya
21	The fourth group of RGB lasers	0-31	Off
		32-63	Tsvuku
		64-95	Girinhi
		96-127	Bhuruu
		128-159	Yero
		160-191	Pepuru
		192-223	Cyan
		224-255	Yakazara kupenya
22	The fifth group of RGB lasers	0-31	Off
		32-63	Tsvuku
		64-95	Girinhi
		96-127	Bhuruu
		128-159	Yero
		160-191	Pepuru
		192-223	Cyan
		224-255	Yakazara kupenya
23	Yechitanhatu	0-31	Off

	group of RGB lasers	32-63	Tsvuku
		64-95	Girinhi
		96-127	Bhuruu
		128-159	Yero
		160-191	Pepuru
		192-223	Cyan
		224-255	Yakazara kupenya
24	Laser kushanda	0-15	Hapana basa
		16-27	Mhedzisiro 1
		......	Every time the DMX value is increased by 12, there will be an effect
		232-243	Mhedzisiro 19
		244-255	Mhedzisiro 20
25	Laser kushanda havukavu	0-255	self-propelled speed from fast to nonoka
26	itangezve	0-249	Hapana basa
		250-255	machine reset (value stays for 5 seconds)

38Channel Mode

CH	basa	DMX Kukosha	Details
1	Pan Motokari	0-255	0-360°positioning
2	Pan Motokari havukavu	0-255	Kubva pakutsanya kusvika pakunonoka
3	Tilt1 motor	0-255	0-360°positioning
4	Tilt2 motor	0-255	0-360°positioning
5	Tilt3 motor	0-255	0-360°positioning
6	Tilt4 motor	0-255	0-360°positioning
7	Tilt5 motor	0-255	0-360°positioning
8	Tilt6 motor	0-255	0-360°positioning
9	Tilt1—Tilt6 motor stroke	0-255	0 hapana basa 1-255 0°-360° positioning
10	Tilt motor speed	0-255	speed from fast to slow
11	Kuzvimiririra	0-55	Hapana basa
		56-80	Self-propelled effect 1 (XY uncontrollable)
		81-105 106-130 131-155 156-180	Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
		181-205	Sound control (XY uncontrollable)
		206-230	Self-propelled effect 6 (XY

			uncontrollable)
		231-255	Sound control (XY uncontrollable)
12	Kuzvimiririra havukavu	0-255	self-propelled speed and Sound-activated sensitivity
13	Dimmer	0-255	0-100% total dimming
14	Strobe	0-9	Hapana strobe
		10-255	Strobe speed kubva kunonoke kusvika kutsanya
15	Red laser 1-6 kudzikira	0-255	0 hapana basa 1-255    1-100% dimming
16	Green laser 1-6 kudzikira	0-255	0 hapana basa 1-255 1-100% dimming
17	Blue laser 1-6 kudzikira	0-255	0 hapana basa 1-255 1-100% dimming
18	The first group of red lasers	0-255	0-100% kuderera
19	The first group of green lasers	0-255	0-100% kuderera
20	The first group of blue lasers	0-255	0-100% kuderera
21	wechipiri group of red lasers	0-255	0-100% kuderera
......	......	......	......
33	The sixth group of red lasers	0-255	0-100% kuderera
34	The sixth group of green lasers	0-255	0-100% kuderera
35	The sixth group of blue lasers	0-255	0-100% kuderera
36	Laser kushanda	0-15	Hapana basa
		16-27	Mhedzisiro 1
		......	Every time the DMX value is increased by 12, there will be an effect
		232-243	Mhedzisiro 19
		244-255	Mhedzisiro 20
37	Laser kushanda havukavu	0-255	self-propelled speed from fast to slow
38	itangezve	0-249	Hapana basa
		250-255	machine reset (value stays for 5 seconds)

Kuchengetedza uye Kuchenesa

Aya mapoinzi anotevera anofanirwa kutariswa panguva yekuongorora:

1. All screws for installing the devices or parts of the device must be tightly connected and must not be corroded.
2. Hakufanirwe kuve nekukanganisa paimba, mavara lenzi, zvigadziriso uye nzvimbo dzekuisa (denga, kumiswa, trussing).
3. Zvikamu zvinofambiswa nemichina hazvifanire kuratidza zvisaririra zvekupfeka uye hazvifanirwe kutenderera zvisina kuenzana.
4. Matambo emagetsi emagetsi haafanire kuratidza chero kukuvadzwa, kuneta kwezvinhu kana sediments.

Further instructions depending on the installation spot and usage must be adhered by a skilled installer and any safety problems have to be removed.

KUSVIRA!
Bvisa pane mains usati watanga kugadzirisa kugadzirisa.

In order to make the lights in good condition and extend the lifetime, we suggest a regular cleaning to the lights.

1. Clean the inside and outside lens each week to avoid the weakness of the lights due to the accumulation of dust.
2. Geza feni svondo rega rega.
3. A detailed electric check by an approved electrical engineer every three months makes sure that the circuit contacts are in good condition, and prevents the poor contact of the circuit from overheating.

We recommend frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents. There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.

Zvinyorwa / Zvishandiso

FOS technologies Razor Laser Multibeam RGB Laser Moving Head [pdf] Bhuku reMushandisi Razor Laser, Multibeam RGB Laser Moving Head, RGB Laser Moving Head, Moving Head, Razor Laser