SMART logo

BRACELET
user’s manual

Wear it properly

The wristband is best worn after the ulnar styloid Adjust the size of the wrist according to the adjustment hole Buckle belt buckle The sensor should be close to the skin to avoid moving。

Charge the bracelet

For the first time, make sure that the battery is in normal power. If the power is not turned on normally, please connect the charger to charge the device, and the bracelet will automatically turn on.

Install the bracelet app on your phone

Scan the QR code or go to the App Store, app download and install the app

SMART WATCHES Smart Bracelet - qr cod

System Requirements: Android 5.0 or above; iOS9.0 or above; Support for Bluetooth 4.0.

Device connection

For the first time, you need to connect to the APP for calibration. After the connection is successful, the bracelet will automatically synchronize the time.

  • Open the phone app →click to start scanning → click on the device connection
  • After the pairing is successful, the APP will automatically  save the Bluetooth address of the bracelet, and when the APP is opened or running in the background, it will automatically search and connect the bracelet;
  • Android mobile phone Please ensure that the APP runs in the background and the mobile phone system settings are given all permissions such as running the background and reading the contact information.

Bracelet function description

  • When the device is turned off, touch and hold the function button for more than 3 seconds to turn the device on
  • In the Bluetooth address interface of the bracelet, press and hold the 2-second wristwatch to turn off the phone. A short press will exit the shutdown page
  • Bracelet reset device This function will clear all data of the bracelet (such as step counting)
  • Under the power-on state, touch the short press function key to light up the screen
  • Whether the default clock page of the bracelet, press the short press function key to switch to view different pages, no operation default five-second screen
  • Switch to the heart rate three-in-one interface to start the test, heart rate three-in-one interface 60s timeout automatically off-screen (heart rate and blood pressure need bracelet hardware support)

Clock interface

After syncing with the phone, the bracelet will automatically calibrate the time.; Press and hold the standby interface for 2 seconds to switch the clock interface of 24/12 hours.
(tracks Step)
Number of steps
Wear the bracelet and record the number of daily movement steps to view the current real-time steps.
Distance
The distance of motion is estimated based on the number of walking steps.
Calorie
Estimate the calories burned based on the number of walking steps
Heart rate, blood pressure, blood oxygen three-in-one
After entering the heart rate three-in-one test interface for a few seconds, the current heart rate, blood pressure, and blood oxygen test results are displayed. This feature requires a wristband to support heart rate and blood pressure sensors
Multi-sport mode
(Running Mode)
Under this interface, you can record the calories and duration of running.
Skipping rope mode)
Under this interface, you can record the calories and duration of rope skipping.
Sit-up mode)
Under this interface, you can record the calories and duration of sit-ups.
Sleep mode)
When you fall asleep, the bracelet will automatically enter the sleep monitoring mode; Automatically detect your deep sleep/shallow sleep/wake up all night and calculate your sleep quality; Sleep data is only supported for APP viewing.
Note: Wearing a bracelet to sleep will have sleep data and start to detect sleep at 10 o’clock in the evening. Sleeping 3/4 hours of sleep data will be synchronized to the APP  while sleeping.
Information mode
When the bracelet pushes multiple reminder messages, enter this interface to view the last 3 message records.

APP function and settings

Personal information)
Please set your personal information after entering the app.
Settings → Personal Information, you can set gender – age – height – weight  You can also set your daily goal steps to monitor daily completions
Application push) incoming call:
In the connected state, if the call alert function is enabled, when the call comes in, the wristband will vibrate and display the name or number of the caller. (You need to give APP read address book permission)
SMS notification:
In the connected state, if the SMS reminder function is enabled, the bracelet will vibrate when there is a text message.
Other reminders:
In the connected state, if this function is enabled, when there is a message such as WeChat, QQ, Facebook, etc., the bracelet will vibrate to remind and display the content received by the app. (You can also view the last three message records in the ring information menu). (You need to give the APP permission to get system notifications. The wristband can display 20-40 words).
Other functions::
Turn on vibration to set this function, When there is a call, message, or another reminder, the bracelet will vibrate. If it is closed, the bracelet will only have a screening reminder without shaking to avoid disturbing.
Tips for Android users: When using the reminder function, you need to set it to allow “FitPro” to run in the background; it is recommended to add “FitPro” to the rights management and open all permissions.
(Alarm setting)
In the connected state, 8 alarms can be set. After setting, it will be synchronized to the bracelet; an offline alarm is supported. After the synchronization is successful, even if the APP is not connected, the bracelet will be reminded according to the set time.
(Looking for a bracelet)
In the connected state, click the “Look for the bracelet” option and the bracelet will vibrate.
(Remote photography)
In the connected state, start the photo from the wristband or the APP to enter the remote camera interface, shake/turn the wrist/touch the bracelet, and automatically take a  photo after 3 seconds of counting down. Please allow the APP to access the photo album to save the self-portrait photo.
(Sedentary reminder)
Set whether to enable the sedentary reminder function, you can set the reminder interval, if you sit for a long time in the set time, the bracelet will remind.
(Raise your hand to brighten)

Turn this function on. When the wristband is in the state of the screen, lift your wrist and turn the screen to yourself to light up the screen.
(Do not disturb mode)
Turn on the Do Not Disturb mode. You can set the Do not disturb time period. During the set time period, the bracelet stops receiving notification messages to avoid reminding messages.
(Device reset)
Setting this feature reset will erase all data in the bracelet (such as step counting)
(Remove device)
Remove device This feature will erase data and remove device
Basic parameters 

Equipment type smart wristband Type of battery Lithium polymer
Vibration motor support method of Bluetooth4.0
synchronization
Operating temperature -10℃~50℃ sensor Low Power Acceleration Sensor
System Requirements iOS9.0 and above/Android 5.0 and above

Precautions

  1. Bathing and swimming should not be worn.
  2. Please Connect the bracelet when synchronizing data.
  3. Use the included charging cable to charge.
  4. Do not expose the bracelet to high moisture, high temperature, or very low temperatures for long periods of time
  5. The bracelet appears to crash and restart. Please Check the phone memory information clear and try again, or exit the APP and reopen it.

Component introduction

*Host *Wrist strap *Charging cable *Packing box and instructions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur n a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Documents / Resources

SMART WATCHES Smart Bracelet [pdf] User Manual
Y68, 2A3YC-Y68, 2A3YCY68, Smart Bracelet, Bracelet

Leave a comment

Your email address will not be published.