Smart Door Locks SDL-K12 Smart KeyBox with App
Install Battery
Remove the (4) screws on the battery cover
Put 4 AAA batteries into the battery dock
Download Mobile App
Scan QR Code below and download the App and turn on your mobile Bluetooth
Add Device
Go to App Home page, click Add Device or click “+” on the upper right.
Press 
+9+ and enter Admin password + , when the light slowly blinks in blue the KeyBox is ready to pair
You will see the detected device and click “Go to add”.
Connecting, you need to wait for few seconds to let it finish
Device added
Change Admin Password-Initial Admin Password:123456
Press and hold for 3 beeps
Right after the 3 beeps please key in Initial Admin Password + +new admin password+ +new admin password
Mechanical Instructions
Password & Factory Mode
Password Length
Password must be 6 digits (no more no less)
Add User Password
Press + 0 + until the blue light blinks
- Enter admin password +
- Enter new user password +
- Enter new user password again and press
- When the (Enter button) blinks in green, user password has been set.
Delete User Password
Press + 2 + until the blue light blinks
- Enter admin password and press
- Enter the user password you wish to delete and press
- Enter the user password again and press
- When the (Enter button) blinks in green the password has been deleted.
Delete All User Password
- Press + 00000 + until the blue light blinks
- Enter admin password and press
- When the (Enter button) blinks in green all passwords have been deleted
Virtual digits-Anti Peeping
Add any digits before and after the correct password the KeyBox unlock as always
System Lockdown
KeyBox will Lockdown for 5 minutes if entering wrong password continuously 5 times
Reset Factory Mode
Press and hold the reset button for 5 seconds and with a long beep
Bluetooth broadcasting & re-connecting:
Press any key to activate the Bluetooth, App&Device will get reconnected each other.
Bluetooth broadcasting will turn to sleep mode if no operations within 1 minute.
App Instructions
- You will see all devices and rooms on the home page.
- Tap the Device to start operating.
- Tap “Me” at the bottom to manage your home
- Touch the lock sign to unlock and lock.
- Tap “Bell” sign to check the alarm records.
- Tap “Member Management to add or delete members.
- Tap “opening record” to check opening logs.
- Tap “Intelligent Linkage” to turn on and off go home mode.
- Tap “Set” to manage passwords
- Tap “Get dynamic code” to get a code.
- Tap “copy code” and send it to friend or family.
- Tap “Pen” sign to edit your personal information
- Go to “Members” to add family or other members
- Tap “+” to add family member or other members
- Tap “ Add it now” under Family to add family members
- Owner need to complete the Home information before adding any family member if required
- The member need to be registered to the App before adding as a family member
- Fill up member information and set the role of the member
- Tap “Save” to complete and the member will be able to operate the device on his App
- Go to “Opening Logs” to check the unlocking history
- With this feture you will be able to find out when and who unlocked the KeyBox
- Go to “Intelligent Linkage” to set more smart functions
- Tap the green bar to turn on “Family go home”function.
- Tap the orange bar to turn on “Door lock alarm”function
- You will get notification if user unlocked with Bluetooth
- Go to “me” homepage and got to message center to check the records.
- Tap “password management” to add or remove codes.
- Tap “Temporary code” to manage online and offline codes
- Tap “one-time code” under Online Code to set an online one time code.
- Tap “periodic Code” under Online Code to set a online code which will be available in a period of time.
- Tap ”One-Time Code” under Offline Code to generate a one time offline code which will be a 10 digits code and use it when the device is offline.
- Tap “Offline Temporary Code” under Offline Code t generate an offline code (10 digits) which will be available in a period of time, and use when the device is offline or Bluetooth disconnected with device.
- Tap “Clear Code” to generate a code (10 digits) which is able to clear Codes that need to be invalid or clear all codes.
- Please note if the code less than 10 digits you need to regenerate a new code, the code must be 10 digits
Documents / Resources
 | Smart Door Locks SDL-K12 Smart KeyBox with App [pdf] User Guide SDL-K12 Smart KeyBox with App, SDL-K12, Smart KeyBox with App, Smart KeyBox, Smart KeyBox App |
