Owner's Manual for Luxman models including: E-250 Phono Amplifier, E-250, Phono Amplifier, Amplifier
LUXMAN E-250 (01) PDF MANUAL - Manual-Hub.com
PHONO AMPLIFIER E-250 Owner`s Manual https://manual-hub.com/ Contents Precautions·············································································································· 1 Features of This Unit································································································· 2 Names and Functions······························································································· 4 Connections············································································································· 8 Block Diagram········································································································ 10 Specifications········································································································· 11 Before Asking for Repair Services··········································································· 12 https://manual-hub.com/ Precautions PHONO AMPLIFIER E-250 Installation place Install this unit in a location where good ventilation and heat radiation are assured. Especially, the installation of this unit where the direct sunlight is present, where the temperature rises excessively high such as close to a heater, or where it is humid or dusty may cause a malfunction even if heat is efficiently released. Therefore, do not install this unit in such places. Note: For heat dispersal, do not install this equipment in a confined space such as a book case or similar unit. * Note * * * Wall Cautions in connecting cartridges Connect an analog player or a tone arm with the ground terminal of this unit. If the grounding terminal is inadequately connected, noises including hum may be generated, resulting in an adverse effect on the S/N ratio. The pin plugs to be inserted in the input terminals of this unit shall be pushed in firmly. If the grounding of the terminal is inadequately connected, noises including hum may be generated, resulting in an adverse effect on the S/N ratio. Precautions in connecting with other components When connecting this unit to output device, be sure to turn off the power switch of this unit and all other connected units. Failure to observe this may generate a strong noise resulting in speaker damage or cause a malfunction. The pin-plugs to be inserted in the input and output terminals of this unit shall be pushed in firmly. If the grounding terminal is inadequately connected, noises including hum may be generated, resulting in an adverse effect on the S/N ratio. The sound is not generated shortly after the power supply is turned on. This amplifier is equipped with a time muting circuit in order to separate the output circuit. Therefore, no sound is generated shortly after the power supply is turned on. If the volume control is set to a high sound level before the time muting circuit is canceled, a large sound will suddenly be generated. Please be advised that the volume control shall be set to a low level at first and adjusted after the sound comes out of the speakers. Repair and adjustment When repairs and adjustments are needed, please consult with the dealer you bought the unit from. Cleaning For cleaning, use a piece of soft cloth to wipe the unit such as cleaning cloth. When the dirt is hard to remove, use a small amount of neutral detergent to wipe, and then wipe the unit with dry cloth. Do not use a solvent like benzine or thinner because such substances can often damage the exterior. https://manual-hub.com/ 1 Features of This Unit Outline This unit is an NF type phono equalizer amplifier supporting MM/MC cartridges. Specially selected MC transformer Two pieces of step-up transformers in which a super permalloy core is independently used are mounted. Independence between left and right channels has achieved richly expressive sound that can be produced only by boosting with a transformer. Setting of cartridge load impedance The load resistance setting function with 4 positions supports a wide variety of cartridges. Setting of cartridge load capacity The load capacity setting function with 4 positions supports a wide variety of cartridges. Change in high-frequency characteristics allows sound to be adjusted to your favorite tone quality. Improvement in S/N ratio Noise reduction has been achieved by the 2-parallized first stage of FET, and improvement in the S/N ratio has been achieved by optimization of ground pattern and ground point. Selector relays The selector relays of the high sound quality which are mounted in the important points of LUXMAN amplifiers also are mounted. High-inertia power supply The high-inertia power supply circuit on which a large-capacity capacitor blocks were combined. Schottky barrier diode Schottky barrier diodes that have less switching noises and higher conversion efficiency to the DC voltage is applied for the power supply rectifier circuit. 2 https://manual-hub.com/ PHONO AMPLIFIER E-250 Articulation function Magnetization of the cartridge or MC transformer that may cause the deterioration of sound quality can be eliminated with the use of reproduced sound signals. This function can exploit the full potential of cartridges and achieve the sound quality with a sense of openness. Low cut switch A low-cut filter is provided to restrain woofer fluctuation generated due to warped analog records. Stereo/Monaural The monaural switch which is useful for playing monaural records. Input/output terminals 18 mm pitch RCA input/output terminals allow even high-performance line cables with large plugs to be connected. Compact chassis design Compact body design (W 364 mm x D 274 mm) LUXMAN's original OFC wires Original OFC wires are used in the internal shielded wires to achieve smooth and natural signal transmissions thanks to the spiral wrap shielding on each core and the non-plating process on the core wire. AC inlet This inlet enables the connection with an external power cable. https://manual-hub.com/ 3 Names and Functions Front panel 21 3 4 56 7 8 9 1. Operation switch (OPERATION) This switch turns on and off the power. When connecting the input/output terminals, be sure to turn off this switch. : OFF : ON 2. Operation indicator (OPERATION) Blinks during warm-up when the operation switch is turned on and lights up when the operation state is activated afterward. When the indicator is blinking, the output muting circuit is activated to mute sound. Please be advised that the volume control of the input device such as a control amplifier shall be set to a low level at first and adjusted according to your taste after sound comes out of the speakers. 3. Mode switch (MODE) · STEREO Is used for stereo playback. Select this position under normal conditions. · MONO Is used for monaural playback. 4. Low cut switch (LOW CUT) Toggles the low-frequency cutoff function on and off. The speaker (woofer) fluctuation is restrained when a warped record is played. · OFF Provides the normal state. · ON Cuts low frequencies of 30Hz or less. (6 dB/oct) 5. Articulator switch (ARTICULATOR) This function performs demagnetization by using sound signals. When a record is played with the articulator switch set to ON, the cartridge and step-up transformer are demagnetized, and thus the expression of fresh sound is brought back. When the articulator switch is set to ON, no sound is generated or the sound becomes remarkably small during playback. This is the sign that the cartridge is being demagnetized. If the articulator is set to OFF at this point, the sound suddenly becomes loud. Therefore, do not turn up the sound volume of the control amplifier or the like. It is recommended to activate the articulator for approximately 30 seconds before the end of a track of the record. · OFF Deactivates the articulator. Select this position under normal conditions. · ON Activates the articulator. 4 https://manual-hub.com/ PHONO AMPLIFIER E-250 6. Articulator indicator Blinks when the articulator is activated. 7. Input selector (INPUT) Selects an input terminal on the rear panel. · 1: Input terminal 1 (INPUT-1) is selected. · 2: Input terminal 2 (INPUT-2) is selected. 8. Cartridge selection switch (CARTRIDGE) Selects between MM and MC according to your cartridge. When MC is selected, the MC cartridge selector (9) can switch between HIGH and LOW and the MC input impedance. 9. MC cartridge selector When the cartridge selector (8) is set to MC, the MC cartridge selector can select an input impedance. This selector switches between HIGH and LOW according to your MC cartridge. The input impedance at the MC HIGH position is 40 , and the input impedance at the MC LOW position is 2.5 . https://manual-hub.com/ 5 Names and Functions Rear panel 10 11 12 13 14 10.Input impedance selector/ input capacitor selector The input impedance and input capacitor can be selected according to your cartridge. The switches in the upper row are used for the L channel, and the switches in the lower row are used for the R channel. The switches 1 and 2 are used for the input impedance, and the switches 3 and 4 are used for the input capacitor. Combination of the switches shown in the figure allows the setting at the L and R channels to be performed at the same time according to your cartridge specifications or your favorite pattern. For the input impedance, 34 k, 47 k, 56 k and 100 k are selectable, and for the input capacitor, 0 pF, 100 pF, 220 pF, and 320 pF are selectable. The input impedance is 47 k and the input capacitor is 0 pF as factory default settings. ON 1234 ON 1234 * Switch positions are marked with in the detailed drawing above. Before changing switch positions, set the sound volume of connected devices to a low level. 6 https://manual-hub.com/ PHONO AMPLIFIER E-250 11. Signal ground terminal (SIGNAL GROUND) Is a ground terminal for devices to be connected to this unit. These terminals are used to reduce noises when other devices are connected, and are connected to an analog player or a tone arm. This terminal is not designed for safety. 12. Input terminals (INPUTS) Are input terminals to connect pin-plug cables from an analog player or a tone arm. There are 2 lines of input terminals to connecte 2 pieces of analog players or tone arms. The input selector can select between 1 and 2. 13. Output terminals (OUTPUT) Use pin-plug cables to connect the output terminals of this product with the line input terminals of a control amplifier and an integrated amplifier. If this terminal is connected to the phono (PHONO) input terminals of those amplifiers, they may be damaged. Be sure to connect the terminal to the line input terminal. 14. AC inlet (AC IN) Connects the accessory power cable. The power shall be supplied from a household wall socket. https://manual-hub.com/ 7 Connections ANALOG PLAYER ANALOG PLAYER L RL R LR CONTROL AMP POWER AMP L R SPEAKER SYSTEM 8 https://manual-hub.com/ PHONO AMPLIFIER E-250 Before Connecting Before connecting other devices, connect the jack side of the accessory power cable to the AC inlet of this unit. Before connection, turn off the main power switch of this unit and the power of all other connected devices to prevent unexpected accidents that may be caused by noise. How to connect power supply Use the accessory power cable to insert the AC plug in an outlet on the wall in the listening room. How to connect output devices 1. Surely connect the output terminals of this unit to the line input terminals of a control amplifier or an integrated amplifier using RCA pin-plug cables between the L-channel and R-channel. If the grounding side of the pin-plug cables is inadequately connected, noises including hum may be generated, resulting in an adverse effect on the S/N ratio. Therefore, insert the cables all the way. 2. Do not connect the output terminals of this unit to the phono (PHONO) input terminal of a control amplifier or integrated amplifier. Failure to observe this may not only distort the phono amplifier signals of the integrated amplifier or a control amplifier but also damage the amplifiers. Be sure to connect the terminal to the line input terminal. Do not insert the supplied short pins into the output terminals. If the pins are inserted into the output terminal, no sound will be generated. 3. Sound volume adjustment shall be performed by the connected control amplifier or integrated amplifier because this unit has no sound volume adjustment function. Sound volume shall be set to the minimum when this unit is being connected. If sound volume is set to a high level at power-on, sudden loud sound may be generated, which may cause hearing loss or damage to the speakers. Please be advised that the sound volume shall be set to a low level at first and adjusted according to your taste after the sound comes out of the speakers. How to connect analog player 1. Mount a cartridge on the tone arm in an appropriate way by referring to the operating instructions of the analog player and cartridge to be used. 2. Insert the pin-plugs of RCA pin-plug cables from the tone arm with a cartridge mounted into the input terminals of this unit. At this moment, be sure to make a connection without a mistake between the R-channel and L-channel. If the grounding side of the pin-plug cables is inadequately connected, noises including hum may be generated, resulting in an adverse effect on the S/N ratio. 3. Grounding between analog players to be connected and this unit is needed. Be sure to connect the ground wires that come from tone arms in parallel with pin-plug cables to the ground terminals of this unit. If the ground wires are inadequately connected, noises including hum may be generated, resulting in an adverse effect on the S/N ratio. Do not connect the output of an analog player with phono equalizer embedded to this unit. Failure to observe this may not only distort the amplifier signals but also cause a malfunction. Connect the output of an analog player with phono equalizer embedded to the line input of an integrated amplifier or a control amplifier. https://manual-hub.com/ 9 10 Block Diagram INPUT PHONO 1 INPUT SELECTOR INPUT LOAD SELECTOR MC LOW MC HIGH MM/MC +B PHONO EQUALIZER AMPLIFIER LOW CUT OUTPUT L ch PHONO 2 IMPEDANCE CAPACITY ARTICULATOR MC STEP-UP TRANSFORMER -B +B INPUT PHONO 1 INPUT SELECTOR INPUT LOAD SELECTOR MC LOW MC HIGH MM/MC RIAA LOW CUT RIAA MONO/ STEREO MUTE PHONO EQUALIZER AMPLIFIER LOW CUT MONO/ STEREO OUTPUT R ch PHONO 2 IMPEDANCE CAPACITY ARTICULATOR MC STEP-UP TRANSFORMER -B OPERATION SW FUSE AC IN Power Transformer Rectifier RIAA LOW CUT RIAA High Inertia Regulator Discrete Regulator Circuit +B For EQ AMP -B MUTE https://manual-hub.com/ Regulator Rectifier For CONTROL CIRCUIT RELAY / INDICATOR Specifications PHONO AMPLIFIER E-250 Input sensitivity MM MC-HIGH MC-LOW : 3.2 mV/250 mV, 1 kHz, load 50 k : 0.37 mV/250 mV, 1 kHz, load 50 k : 0.12 mV/250 mV, 1 kHz, load 50 k Input impedance MM MC-HIGH MC-LOW : 34 k/47 k/56 k/100 k (switch selection) : 40 : 2.5 Gain MM MC-HIGH MC-LOW : 38 dB : 57 dB : 66 dB RIAA deviation MM MC-HIGH MC-LOW : 20 - 20 kHz±0.3 dB : 20 - 20 kHz±0.5 dB : 20 - 20 kHz±0.5 dB Maximum allowable input voltage MM MC-HIGH MC-LOW : 120 mV : 15 mV : 5 mV Output impedance 300 S/N ratio (at 250 mV output) MM MC-HIGH MC-LOW : 90 dB (IHF-A) : 83 dB (IHF-A) : 80 dB (IHF-A) Total harmonic distortion (at MM 1 V output) 0.003% Channel separation (10kHz) 91dB or more Accessories · Power cable · Owner's Manual (This document) · Safety cautions Circuiting system NF type equalizer amplifier equipped with MC step-up transformer Power consumption 7 W Power supply 230 V (50 Hz) Max. external dimensions 364 (W) x 81 (H) x 274 (D) mm (front side knob of 6mm and rear side terminal of 11 mm included in depth) Weight 4.3 kg (main unit only) * Specifications and the appearance are subject to change without notice. https://manual-hub.com/ 11 Before Asking for Repair Services While the unit is used, an unusual phenomenon may be confused as a malfunction for a certain reason. Prior to asking our official sole distributor of your country for repair services, please check the table below and read the operating instructions for the subsidiary devices. If the cause of the malfunction cannot be identified, please contact your dealer. When we have once accepted your request for repair services, inspection fees and traveling expenses may be claimed even though the unit is found to be normal. Problem No power is supplied even though the operation switch is pressed. No sound is generated. (small sound) Humming sound (boon or zzz noise) is generated. Inappropriate localization of sound No bass is generated. Cause Solution · The power plug is disconnected from the wall outlet, or it is not completely inserted. · The power plug is disconnected from the AC inlet, or it is not inserted completely. · Connection is not securely performed. · The connected input terminal does not match the setting of the input selector switch. · The selector of the input device such as a control amplifier is not correctly set. · The volume control of the input device such as a control amplifier is not set to a lower level. · The used cartridge type does not match the selected item of the MM/MC selector switch. · The articulator position is selected. · The grounding side of the connection cable has no contact with the terminal. · The grounding of the shell or tone arm is inadequately connected. · Induction noise is picked up from a power transformer of another device. · The connecting cables are too close to the power cable. · The L channel and R channel are connected reversely. · The setting of the input impedance control does not match the cartridge in use. · Insert the power plug in the wall outlet completely. · Securely insert the power plug in the AC inlet. · Make cable connections securely. · Match the input terminal with the setting of the input selector switch. · Set the selector of the input device such as a control amplifier correctly. · Adjust the volume control of the input device such as a control amplifier. · Select the correct item of the cartridge selector switch according to the cartridge to be used. · Turn down the sound volume and adjust the sound volume according to the appropriate input impedance after sound comes out. · Make cable connections securely. · Be sure to connect the ground wire of the shell or tone arm to the ground terminal. · Install it distant from other devices. · Keep the connecting cables away from the power cable. · Connect the L channel and R channel appropriately. · Adjust the input impedance according to the cartridge in use. 12 https://manual-hub.com/ https://manual-hub.com/ LUXMAN CORPORATION, JAPAN 1-3-1 Shinyokohama, kouhoku-ku, Yokohama-shi, Kanagawa 222-0033, Japan https://manual-hub.com/ AG00987E51A Printed in Japan