HUNTER Klein 19440 Light Pendant
i lugaview
FAASINO MATAFAIOI
LAPATAIGA
- To avoid possible electrical shock, beforeinstalling your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location
- O le moli moli e tatau ona faʻavae. Afai e le oi ai le uaea eleele mo le nofoaga faʻapipiʻi, vave STOP faʻapipiʻi ma faʻafesoʻotaʻi se eletise agavaa.
- O fesoʻotaʻiga uma e tatau ona o gatasi ma tulafono faʻale eletise a le atunuʻu ma faʻalotoifale ANSI / NFPA 70. A faʻapea e te le masani i le faʻapipiʻiina poʻo le masalosalo, faʻafesoʻotaʻi se tagata faʻapitoa tau eletise.
FAITAU MA FAASAO NEI FAATONUGA
O nei faʻatonuga e avatua mo lou saogalemu. E taua tele lo latou faitau ma le faʻaeteete ma maeʻa aʻo leʻi amataina le faʻapipiʻiina o moli moli.
O mea faigaluega nei e te mana'omia e fa'auma ai lau fa'apipi'i
SAUNIUNIGA MO FAʻAMATALAGA
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop (E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G) to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..
FAʻATASIINA O LE FAʻATASI
There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of canopy (D), and canopy loop (E). Screw the top rod to canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).
Faʻafesoʻotaʻi O UTA
Fa'apipi'i uaea o le mea fa'apipi'i i uaea sapalai eletise mai le pusa fa'atasi. Fesootai le uliuli i le uliuli (Ola); pa'epa'e i le pa'epa'e (grounded); fa'avae i le fa'avae (lanumeamata po'o kopa). Mimilo fa'atasi pito o uaea. Ona, mimilo i luga o se uaea so'oga. Ia mautinoa o mimilo uma o loʻo i le itu e tasi. Fa'amau le uaea fa'aele'ele o lo'o fa'ata'amilo i le fa'avae (C) ma fa'amau. Afai e leai se uaea eleele (lanumeamata po'o le kopa) mai le pusa fa'afeso'ota'i, fa'afeso'ota'i se fai eletise agavaa
FAʻAIUINA O LE INSTALLATION
Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Carefully install glass shade (M) over socket (L), then install socket cover (N) and tighten up the glass shade with socket ring (O). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattagu. Ua mae'a nei lau fa'apipi'i. Ki le paoa ma su'e le mea fa'apipi'i.
MANATU FAʻAMAMALAMAINA
Taulima lemu le mea faapipii! O le faʻamamaina masani o le a faʻaititia ai le manaʻoga mo le loloto o le faʻamamaina. Mo le faʻamamaina masani, tape le moli ma solo i lalo le mea faʻapipiʻi i se mama e leai ni lint-leai se vavae poʻo se microfiber ie. Aua le faʻasasaʻo le fufulu mama i luga o le mea faapipii.
FAAALIGA
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod
Hunter Pro Fautuaga
Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access
Pepa / Punaoa
 |
HUNTER Klein 19440 Light Pendant [pdf] Tusi Taiala Klein 19440, Klein, 19440, Light Pendant |
