Logotip Honeywell

H-razred - logotip

HD Peel & Present Option

Možnost notranjega previjanja z motorjem Honeywell OPT78-2627 razreda H - detamexprav s strani naših strank.

Možnost toplotnega prenosa razreda H Honeywell OPT78-2613-04

Overview

This document describes the contents, installation, and use of the Heavy Duty Peel and Present option for the H-Class printer. After verifying the contents of the kit and the tools needed, follow the steps below to install and begin using the option. A maintenance procedure is also included, so keep this documentation for future reference.

Opozorilo POZOR
For your safety and to avoid equipment damage, always turn ‘Off’ power and unplug the printer’s power cord before beginning this installation and when performing service.

Contents of the Heavy Duty Peel and Present Option

Ta komplet vsebuje naslednji predmet:
• Heavy Duty Peel and Present Assembly

Honeywell H-4310 H-Class HD Peel and Present Option - Heavy Duty Peel and PresentPotrebna orodja
Za namestitev te možnosti boste potrebovali standardni izvijač.

1. korak: Priprava tiskalnika

A) Izklopite 'Off' Stikalo za vklop in izvlecite napajalni kabel iz AC vtičnica.

Honeywell H-4310 H-Class HD Peel and Present Option - Preparing the Printer

B) Pritisnite Ujemite, nato povlecite naprej, da odstranite Vrata.

Honeywell H-4310 H-Class HD Peel and Present Option - DoorC) Dvignite Pokrov za dostop in odstranite svoj medij iz tiskalnika.

Honeywell H-4310 H-Class HD Peel and Present Option - Access Cover

D) Odstrani Vijak za palec in Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.)

Step 2: Installing the Heavy Duty Peel and Present Assembly

A) Pritisnite Zapah in odprite Peel and Present Montaža.

Honeywell H-4310 H-Class HD Peel and Present Option - Present Assembly

B) Previdno pritisnite na Peel and Present Assembly v Front Plate Connector.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present

C) Zategnite Pritrdilni vijak za zavarovanje Peel and Present Assembly na tiskalnik.

3. korak: Uporaba možnosti
Med delovanjem se nalepke odlepijo s podlage in oddajo "na zahtevo" - to pomeni, da bo do nadaljnjega tiskanja prišlo šele po odstranitvi predhodno natisnjene nalepke iz tiskalnika. Kot opomnik bo prikazano »ODSTRANI OZNAKO«, ki vas bo pozvalo, ko nalepka čaka na odstranitev.

Začnite uporabljati možnost na naslednji način:

A) Obremenitev mediji (za podrobnosti glejte Uporabniški priročnik). Razširite 20 palcev (50 cm). mediji iz tiskalnika.

Honeywell H-4310 H-Class HD Peel and Present Option - Media

B) Odstranite nalepke s tega razširjenega dela medija, pri čemer pustite samo Podložni material. Prepognite vodilni rob tega BackingMaterial.
C)
Smer po Podporni material pod Pomožni valj in Internal Rewinder.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing

D) Zavijte Podporni material v nasprotni smeri urinega kazalca okoli Pesto za navijanje and insert the creased leading edge into one of its Slots. Insert the Zaponka za medije (Item 6) into the Slot over the creased leading edge of the Podpora Material and around the Rewinder Hub.

Honeywell H-4310 H-Class HD Peel and Present Option - Backing Material

E) Zapri Peel and Present Assembly. Close the Access Cover, plug the power cord into the AC Receptacle, and turn ‘On’ the Power Switch.

Honeywell H-4310 H-Class HD Peel and Present Option - Peel and Present Assembly

F) Zagotovite to READY is displayed on the Front Panel then press the FEED Key in nadaljujte po svojih opažanjih:

  • If REMOVE LABEL is displayed on the Front Panel, this completes the installation; or,
  • If REMOVE LABEL is not displayed on the Front Panel, proceed to step 4: “Configuring the Printer.”

Honeywell H-4310 H-Class HD Peel and Present Option - Front Panel

Opombe:

  1. Delovanje Present Sensor pri tej možnosti je mogoče nadzorovati tudi z ukazi gostiteljske programske opreme, zato poskrbite, da je vaš program za označevanje pravilno konfiguriran za uporabo pri pošiljanju formatov nalepk v tiskalnik.
  2. Če je ta možnost odstranjena z vključenim napajanjem, se bo tiskalnik obnašal, kot da bi nalepka čakala na odstranitev; da obnovite normalno delovanje, preklopite na napajanje tiskalnika.

4. korak: Konfiguriranje tiskalnika

While the Heavy Duty Peel and Present option is a plug-and-play device, this step may be necessary if the printer’s default configuration has been changed. Follow the steps below to configure the printer:

Opomba: V naslednjem postopku si oglejte navodila za uporabo za podrobna navodila na sprednji plošči.

A) Pritisnite MENU Button on the printer’s front panel.
B) Uporaba DOL Button, scroll to MOŽNOSTI TISKALNIKA then press the Right Button.
C) Uporaba DOL Button, scroll to PRISOTNI SENZOR nato pritisnite Tipka ENTER.
D) Uporaba DOL Button, scroll to MODE nato pritisnite Tipka ENTER.
E) Uporaba DOL Button, scroll to AUTO nato pritisnite ENTER Ključ.
F) Pritisnite EXIT Key then, at the SHRANI SPREMEMBE? poziv, izberite DA za dokončanje namestitve.
G) Turn the Power Switch 'Izklopljeno' in ‘On’ to reset the printer and complete the configuration.

Opomba: If the printer fails to separate the labels from the backing material, and the Internal Rewinder is not turning, it may need to be enabled. Using the procedure above as a guide, press the MENU Button, scroll to PRINTER OPTIONS, nato na REWINDER, in izberite SAMODEJNO. Afterward, press the EXIT key and save your changes when prompted.

Maintaining the Heavy Duty Peel & Present Assembly

To ensure trouble-free operation, the Heavy Duty Peel and Present Assembly should be cleaned after every 100,000 inches (254,000 cm) of media use. This interval depends on the label adhesive, where “gummy” adhesives may require more frequent cleaning. (To easily track label usage, go to SYSTEM SETTINGS → MEDIA COUNTERS in the printer’s menu system.)

Clean the assembly as follows:

  1. Izklopite stikalo za vklop in izvlecite napajalni kabel iz AC vtičnice. Dvignite pokrov za dostop in odstranite medij iz tiskalnika.
  2. Remove the Peel & Present Assembly from the printer.
  3. S stisnjenim zrakom ali mehko krtačo očistite Senzorji on the assembly.Honeywell H-4310 H-Class HD Peel and Present Option - SensorsOpomba: Za čiščenje močnih usedlin lahko uporabite izopropilni alkohol – pod pogojem, da ga previdno nanesete z vatirano palčko in nato pustite, da se posuši, preden ponovno priključite opcijo na tiskalnik.
  4. Pritisnite Zapah to open the Peel and Present Assembly. Then remove the C-sponka that secures the Upper Roller Shaft k Front Cover.Honeywell H-4310 H-Class HD Peel and Present Option - Front Cover
  5. Remove the Upper Roller Shaft and the associated Rollers.Honeywell H-4310 H-Class HD Peel and Present Option - Rollers
  6. Uporaba Vatirana palčka dampened with alcohol, wipe all Roller in Upper Roller Shaft surface clean. Pay special attention to the ridges on the valji to ensure that they are clean.
    Opomba: For cleaning heavy deposits from the Rollers and Shafts in the following steps, WD-40 or another non-damaging adhesive remover can be substituted for isopropyl alcohol – provided this adhesive remover is carefully applied using a cotton swab.
  7. Potisnite gumb valji nazaj na Upper Roller Shaft, place the components into the Front Cover, and reinstall the C-Clip.
  8. Push in dvigalo tako Zavihki ki varujejo Lower Roller Assembly to the Front Cover (as shown) and then, while keeping it intact, carefully remove the entire Lower Roller Assembly.Honeywell H-4310 H-Class HD Peel and Present Option - Tabs
  9. Take note of the individual Roller positions – they must be reinstalled in the same order – then, carefully remove the valji Iz Lower Roller Shaft.Honeywell H-4310 H-Class HD Peel and Present Option - Lower Roller Shaf
  10. Uporaba Vatirana palčka dampened with alcohol, wipe all Roller in Lower Roller Shaft surfaces clean. Pay special attention to the ridges on the valji to ensure that they are clean.
  11. Potisnite gumb Rollers, in their original order, onto the Lower Roller Shaft and reinstall them in the Front Cover, zagotavljanje, da Zavihki are properly seated. Reinstall the Peel and Present Assembly onto the printer to complete the cleaning procedure.

Dokumenti / Viri

Honeywell H-4310 H-Class HD Peel and Present Option [pdf] Navodila
H-4310, H-Class, HD Peel and Present Option, H-4310 H-Class HD Peel and Present Option

Pustite komentar

Vaš e-naslov ne bo objavljen.