EVENT LIGHTING APRO4-IP DMX Controller

Zaradi vaše varnosti pred uporabo natančno preberite ta uporabniški priročnik.
Event Lighting si pridržuje pravico, da kadar koli spremeni priročnik. Informacije in specifikacije v tem priročniku se lahko spremenijo brez predhodnega obvestila. Event Lighting ne prevzema nobene odgovornosti za morebitne napake ali opustitve. Za kakršna koli pojasnila ali informacije v zvezi s to postavko se obrnite na Event Lighting.

ZNAČILNOSTI

• DMX 512, RDM, Artnet and sACN support
• Oddaljena konfiguracija preko internega webstrani
• Update firmware on Webstrani
• DMX output isolation
• RJ45 Ethernet B input with POE（DC12V 2A）
• LCD zaslon
• Gigabit network, 100/1000mbps port speed
• Ocena IP65

PANEL PREKOVIEW

1. Ethernet port RJ45
2. Ethernet port RJ45
3. Power in/out True1
4. 2xDMX5pin connectors
5. 2xDMX5pin connectors
6. Nosilec varovalke
7. LCD Display protection cover

MENIJI
Below is controller Menus map

Glavnimeni	Podmeni 1	Podmeni 2	Vrednost/Možnost	Privzeto
Omrežje	Način IP		DHCP	Statično
			Statično
	IP naslov		2.xx.xx.xx	2.xx.xx.xx
	Subnet Mask		255.0.0.0	255.0.0.0
Vrata DMX	Protokol	Artnet		Artnet
		sACN
	Start Net		000-127	000
	Zaženi Universe		000-255	000
	Vrata 1	Način	Izključeno	On
			On
		NET	000-127	000
		Vesolje	000-255	000
	Vrata 2	Način	Izključeno	On
			On
		NET	000-127	000
		Vesolje	000-255	001
	Vrata 3	Način	Izključeno	On
			On
		NET	000-127	000
		Vesolje	000-255	002
	Vrata 4	Način	Izključeno	On
			On
		NET	000-128	000
		Vesolje	000-255	003
			Onemogoči
nastavitve	Stopnja DMX		20Hz	30Hz
			25Hz
			30Hz
			35Hz
			40Hz
	RDM	Onemogoči		Onemogoči
		Omogoči
	Prikaz vklopljen	Vedno		1 min
		30 sek
		1 min
		5 min
	Izguba signala	Drži DMX		Drži DMX
		Stop Output
	Način spajanja	PH		PH
		LTP
	Ponastavitev na tovarniške nastavitve	št		št
		ja

WEB konfiguracijo

NET device network IP mode can set to DHCP mode or Static mode.

Način DHCP

• When APRO4‐IP is set to DHCP mode, you need to set the computer to DHCP also. And use a router for linking computer and APRO4‐IP device. The controller will show IP address like below:
• Enter IP address in your web browser, then you can login webpage to configure the parameter of controller.

Vnesite geslo: admin

Statični način

• When APRO4‐IP device is set to Static mode, you need to set computer to be Static mode also. APRO4‐IP device will show IP address as below:
• Then set the IP address of computer is in the same IP range manually. For example: IP address must start with 2 according to APRO4‐IP address. And netmask is same with 255.0.0.0.
• Input static IP address of APRO4‐IP device in your browser, then you can login to configure the parameter of device.

Vnesite geslo: admin

• When log on NET Config web, the first page show the information about APRO4‐IP.
• Following  is  for  Network  setting,  you  can  set  IP  mode  to  be  Static  or  DHCP,  IP  Address,and Subnet Mask. After setting, click Save button .
• For DMX Port page , it is used for DMX Port setting. You can select Protocol to be Artnet or sACN, and set each port as input or output.
• On the page of Setting , you can set DMX Rate, RDM , Display On and Signal Loss. After setting, click Save to store the setting.
• DMX  Rate:  You  can  set  20Hz,  25Hz,  30Hz,  35Hz,  40Hz,  30Hz  is default setting.
• RDM: You can set RDM to be Disable or Enable.
• There is 4 options for Display On mode: Always, 30Sec, 1Min, 5Min.
• Izguba signala: Can set as Hold DMX or Stop Output.
• You can return to factory setting by click Factory Reset button.
• On Update page, you can update software of fixture by selecting the update software file of APRO4‐IP.
• On the last page, you can reset password.

SPECIFIKACIJA

• Moč: AC 100‐240V,50/60Hz
• Poraba energije: AC240V 50HZ 0.05A
• Velikost: 215.3×150.5x42mm 4.2W
• Teža: 1.43 kg
• POE 802.3af
• IP65

DIMENZIJE

Garancija

Obrnite se na vašega lokalnega prodajalca ali se obrnite na Event Lighting. www.event‐lighting.com.au

Pogosto zastavljena vprašanja

How do I reset the APRO4-IP device to factory settings?

To perform a factory reset on the APRO4-IP device, access the Factory Reset option in the Main Menu under Settings. Confirm the reset to restore the device to its default configuration.

What is the default IP address for the APRO4-IP device?

The default IP address for the APRO4-IP device is set to DHCP mode. If you switch to Static mode, you can set a specific IP address within the range provided in the user manual.

Dokumenti / Viri

EVENT LIGHTING APRO4-IP DMX Controller [pdfUporabniški priročnik APRO4-IP, APRO4-IP DMX Controller, DMX Controller, Controller

Reference

• Uporabniški priročnik