SatLink WS-6909 DVB-S/DVB-T Combo Satellite Signal Finder Meter User Manual

1. Uvod

The SatLink WS-6909 is a versatile digital meter designed for aligning both DVB-S (satellite) and DVB-T (terrestrial) signals. Featuring a 3.5-inch high-definition TFT LCD screen, it allows users to view actual channels directly on the device, ensuring quick and accurate signal alignment. The meter includes a unique calibration system for optimal performance and supports various satellite and terrestrial signal parameters.

Opomba: DVB-T functionality may not be supported in all regions, including America.

2. Vsebina paketa

Prosimo, preverite, ali so v vašem paketu priloženi vsi spodaj navedeni artikli:

• 1 x SatLink WS-6909 Satellite Meter
• 1 x napajalnik
• 1 x AV kabel
• 1 x kabel za avtomobilski polnilnik
• 1 x silikonski etui

3. Izdelek je končanview

Familiarize yourself with the components and ports of your SatLink WS-6909 meter.

Slika 3.1: Spredaj view of the SatLink WS-6909 meter, showing the 3.5-inch LCD screen, control buttons, and numeric keypad, alongside its protective orange silicone case.

Slika 3.2: Spodaj view of the device, featuring the main power switch, DC power input port, and a USB port for software upgrades.

Slika 3.3: Stran view of the meter, illustrating the AV IN and AV OUT ports for connecting external video sources or displays.

Slika 3.4: Vrh view of the device, displaying the F-connector for satellite input and the standard antenna input for terrestrial signals.

4. Nastavitev

4.1 Polnjenje naprave

1. Connect the provided Power Adaptor to the DC input port on the bottom of the meter.
2. Plug the Power Adaptor into a standard electrical outlet. The 'Charge' indicator light on the device will illuminate.
3. Allow the device to charge fully before initial use. A full charge provides approximately 4 hours of operating time.
4. Alternatively, use the Car Charger Cable to charge the device in a vehicle.

4.2 Začetni vklop

1. Ensure the device is adequately charged.
2. Flip the main power switch located on the bottom of the meter to the 'ON' position.
3. The device will power on and perform an automatic calibration for optimal performance.

4.3 Connecting Antennas/LNBs

• For satellite signal reception (DVB-S), connect the LNB cable from your satellite dish to the F-connector input on the top of the meter.
• For terrestrial signal reception (DVB-T), connect your terrestrial antenna cable to the standard antenna input on the top of the meter.

5. Navodila za uporabo

5.1 Osnovna navigacija

• Uporabite MENI gumb za dostop do glavnega menija.
• Navigate through menu options using the directional arrow buttons (GOR/DOL/LEVO/DESNO).
• Pritisnite OK button to confirm selections or enter sub-menus.
• Uporabite EXIT gumb za vrnitev na prejšnji zaslon ali izhod iz menija.
• The numeric keypad can be used for direct input of values such as frequencies or channel numbers.

5.2 DVB-S (Satellite) Signal Finding

1. From the main menu, select the DVB-S measurement mode.
2. Configure parameters such as satellite, transponder frequency, symbol rate, and polarity. These settings can be modified by the user.
3. The meter supports DISEQC 1.0, 1.1, 1.2, and 22kHz Tone. Adjust these settings as required for your LNB configuration.
4. The meter provides LNB power supply options of 18V/13V (maximum 400mA).
5. Align your satellite dish while observing the signal strength, quality, BER (Bit Error Rate), S/N (Signal-to-Noise ratio), and PWR (Power) on the 3.5-inch LCD screen.
6. The device will provide a sound and light alarm when a signal is locked.
7. The meter can automatically calculate Azimuth (AZ) and Elevation (EL) angles to assist with dish alignment.
8. Search modes include Auto, Blind, and Manual.

5.3 DVB-T (Terrestrial) Signal Finding

1. From the main menu, select the DVB-T measurement mode.
2. Configure the desired frequency range.
3. The meter supports ANT power supply options of 5V/12V/24V for active antennas.
4. Align your terrestrial antenna while observing the signal strength, quality, MER (Modulation Error Ratio), S/N (Signal-to-Noise ratio), and PWR (Power) on the LCD screen.
5. The meter supports multichannel checks and demodulation types including QPSK, 16QAM, and 64QAM.
6. Search modes include Auto and Manual.

5.4 Software Upgrades

The USB port on the bottom of the device is used for software upgrades. Refer to the manufacturer's webspletno mesto za najnovejšo programsko opremo in navodila.

6. Vzdrževanje

6.1 Čiščenje

• Wipe the device exterior with a soft, dry cloth.
• Ne uporabljajte tekočih čistil ali topil, saj lahko poškodujejo napravo.

6.2 Skrb za baterije

• Za podaljšanje življenjske dobe baterije naprave ne izpostavljajte ekstremnim temperaturam.
• Recharge the battery regularly, even if the device is not in frequent use.

6.3 Posodobitve programske opreme

Občasno preverite uradne podatke proizvajalca website for available software updates. Updating the firmware can improve performance and add new features.

7. Odpravljanje težav

8. Specifikacije

• Zaslon: 3.5-palčni TFT LCD zaslon visoke ločljivosti
• Baterija: 8.4V/3000mAh Li-ion, Max Operating Time: 4 hours
• DVB-S Input Frequency: 950-2150MHz
• DVB-S Input Level: -65 do -25 dBm
• DVB-S Input Impedance: 75Ω
• DISEQC Support: 1.0, 1.1, 1.2 and 22kHz Tone
• LNB Power Supply: 18V/13V (IMax 400mA)
• DVB-T Frequency Range: 46MHz-862MHz
• DVB-T Level Range: 40dBµV-110dBµV
• DVB-T Input Impedance: 75Ω
• DVB-T Demodulation: QPSK, 16QAM, 64QAM
• ANT Power Supply: 5V/12V/24V
• Vrste meritev: Signal strength, quality, BER, S/N, PWR (DVB-S); Signal strength, quality, MER, S/N, PWR (DVB-T)
• Načini iskanja: Auto, Blind, Manual
• Dimenzije izdelka: 3.54 x 1.77 x 6.46 palcev
• Teža artikla: 1.76 funtov
• Številka modela: WS 6909

9. Garancija in podpora

For technical assistance, warranty information, or customer support, please contact your original retailer or refer to the manufacturer's official website for contact details. Please have your product model number (WS 6909) and purchase information ready when seeking support.