SKYDANCE DH4 Dali DMX 4 Channel Switch

FEATURES

• 4 DALI address, 4 channel 16A dry contact mains rated relay switch output.
• OLED display screen, via button setting two work modes: DALI mode, DMX mode.
• DALI address can be manually assigned and shown on the digital display or automatically assigned by the DALI master.
• By DALI standard protocol IEC 62386-101,102, 208 and in compliance with DALI products from other international incorporation.
• Comply with the DMX512 standard protocols.
• RDM function can realize intercommunication between the DMX master and decoder.
• Supports manual switching of individual channels.
• High-inrush specification relays (single pole, normally open).
• Zero cross-switching function. Can operate as:
  • 4 individual channels (4 × 1)
  • 2 sets of 2 channels (2 × 2)
  • 1 set of 4 channels (1 × 4)

Technical Parameters

Input and Output

• Input voltage       100-240VAC
• Input current        O.1A
• Input signal        DALI+DMX512
• No-load standby power consumption    0.5W@100V, 1.5W@240V
• Full load loss power        4W@10OV, 4.5W@240V
• Relay contacts     High inrush (120 A at 20ms), single-pole, single-throw (SPST) relay.
• Max relay load current      16A resistive load (incandescent lamp) 8A Capacitive load (LED dimming driver) 8A inductive load (fluorescent lamp

Safety and EMC

• EMC standard (EMC)      301 489-1 V2.2.3  ETSI EN 301 489-17 V3.2.4
• Safety standard(LVD)          ETSI EN EN 62368-1:2020+A11:2020
• Certification            CE, EMC, IVD

Warranty and Protection

• Warranty    5 years

Environment

• Operation temperature          Ta: -20 °C ~ +50°C
• Case temperature (Max.)        Tc: +60°C
• IP rating                                    IP20

Package

• Size                                            W118 x L102 x H71 mm
• Gross weight                           0.345kg

Mechanical Structures and Installations

Wiring Diagram

Note:
The maximum surge current of the AC output is 120A, the sum of the surge current of multiple resistive loads or inductive loads (LED drivers )should not exceed its maximum value. Otherwise, the product will be overloaded and damaged.

Work Mode

System setting

• Long press the M button for 2s, enter the system setting state and prepare to set the working mode, channel number, and manual switch. Short press the M button to switch three setting items.
• Working mode: Short press the ◀ or ▶ button, and switch between DALI and DMX working mode.
• Channel number: Short press ◀ or ▶ button, switch the number of 4/2/1 channels, i.e. 4 independent channels (4×1), 2 groups of 2 channels (2×2), or 1 group of 4 channels (1×4).
• The manual switch enables the Short press ◀ or ▶ button, setting to allow (Yes) or disallow (No) the manual switching function, i.e. setting whether the four-channel manual switching buttons are active or not.
• Long press the button for 2s, or timeout 15s, and uit the system setting.

DALI mode

In DALI mode, the DALI address can be set by buttons or DALI master control:

• Set DALI Address via buttons
  • Short press the M button, and prepare to set the start DALI address. The four channels can be addressed separately, and the address setting of the four channels can be switched sequentially by short pressing the M button.
  • Short press the ◀ or ▶ button, to change the address value of the current channel (00-63-FF), FF means unassigned DALI address. Long press for fast adjustment.
  • Long press Mthe button for 2s, or timeout 15s, and uit Dthe ALI address setting.
• DALI address assigned by DALI masters DALI address can also be assigned by DALI Master controller automatically.
  • Please refer to user manuals of compatible DALI Masters for specific operations.

DMX mode

In DMX mode, the DMX address can be set by buttons or DMX RDM master:

• Short press the M button, and prepare to set the start DMX address. Only the address of the rst channel needs to be set, and the addresses of the other channels will be automatically added 1 in sequence.
• Short press the ◀ or ▶ button, change the DMX address value (001-512), and long press for fast adjustment.
• Long press the M button for 2s, or timeout 1andqand the the MX address setting.
• DMX control: When the DMX data value is <50, the relay output is off.
  • When the DMX data value is >200, the relay output is on.
  • When the DMX data value is between 50 and 200, keep the previous on/off status.

Restore factory settings

• Long press the ◀ and ▶ buttons at the same time for 2 seconds to restore factory settings.
• Factory default parameter: DALI mode, number of channels is 4, manual switch enabled.

Overheat protection

• 110°C triggers temperature protection and shuts off the relay output.
• Normal switching control is resumed at 90°C.

WEBSITE: www.iskydance.pl

Documents / Resources

SKYDANCE DH4 Dali DMX 4 Channel Switch [pdf] Owner's Manual DH4, DH4 Dali DMX 4 Channel Switch, DH4, Dali DMX 4 Channel Switch, DMX 4 Channel Switch, 4 Channel Switch, Channel Switch, Switch

References

• User Manual