STIEBEL ELTRON logo

Plniaca jednotka soľanky STIEBEL ELTRON 233307 WPSF

Plniaca jednotka soľanky STIEBEL ELTRON 233307 WPSF

Všeobecné informácie

This document is intended for qualified contractors
Poznámka: Read these instructions carefully before using the appliance and retain them for future reference. Pass on these instructions to a new user if required.
Ďalšie symboly v tejto dokumentácii
Poznámka: General information is identifed by the adjacent symbol.

Tento symbol označuje, že musíte niečo urobiť. Kroky, ktoré musíte urobiť, sú popísané krok za krokom.

Príslušné dokumenty
Heat pump operating and installation instructions
Jednotky merania
Note: All measurements are given in mm unless stated oth­erwise.

bezpečnosť

Only a qualified contractor should carry out installation, com­missioning, maintenance and repair of the appliance.
 Všeobecné bezpečnostné pokyny
Bezporuchovú funkciu a prevádzkovú spoľahlivosť zaručujeme len pri použití originálneho príslušenstva a náhradných dielov určených pre spotrebič.
Pokyny, normy a nariadenia
Note: Observe all applicable national and regional regula­tion
Zamýšľané použitie
The brine charging unit is a multi-function valve for filling and filtering brine-based fluids. Any other use beyond that described shall be deemed inappro­priate. Observation of these instructions and of the instructions for any accessories used is also part of the correct use of this appliance.

Popis výrobku

The product includes a safety valve, a pressure gauge, a filter, a quick-action air vent valve and a microbubble separator.

Štandardné doručenie

  • Bezpečnostný ventil
  • Hákový kľúč

Príprava

The product is installed in the heat source system in the heat pump installation room.

  • Observe the flow direction (see chapter “Specification/Dimensions and connections”).
  • When installing the product, ensure that it is horizontal and free from stress.

Minimálne vôle 

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 1

Maintain the minimum clearances to ensure trouble-free operation of the appliance and facilitate maintenance work.

inštalácia

Fitting the drain hose 

  •  Fit the drain hose supplied to the safety valve.
  • Size the drain hose so that brine can drain off unimpeded when the safety valve is fully opened.
  • Lay the safety valve drain hose with a constant fall to the drain.
  •  Ensure that the safety valve drain hose is open to the outside.

Charging the heat source system

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 2

  1. Shut-off valve, heat source flow
  2. Quick-action air vent valves
  3. Shut-off valve, heat pump flow
  4. Plniaca
  5. Vysušiť
  • Close the shut-off valve in the heat source flow.
  • Open the shut-off valve in the heat pump flow.
  • Connect the refrigerant flow line to the charging side of the unit.
  • Connect the refrigerant return line to the draining side of the unit.
  •  Carry out a pressure test. Remove the safety valve and in­sert the plug supplied.

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 3

  1. Bezpečnostný ventil
  2. Zástrčka
  • Check for tightness.
  •  Charge the heat source system to the required operating pressure. For this, observe the maximum operating pres­sure (see chapter “Specification/ Data table”)
  •  Close the shut-off valve in the heat pump flow.
  •  Remove the plug and refit the safety valve.
  •  Vent the heat source system via the quick-action air vent valve.
  •  After venting, close the quick-action air vent valve.

Removing the strainer
If there is a high pressure drop in the heat source system, you can remove the strainer in the filter chamber of the product (see chapter “Specification/ Pressure drop diagram”).

Materiálne straty 

For opening and closing the filter chamber, use exclusively the hook wrench supplied.

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 4

  1. cedidlo
  2. Filtračná kazeta
  • Open the filter chamber. Remove the filter cartridge.
  • Remove the strainer from the heat pump flow.
  •  Re-insert the filter cartridge. Close the filter chamber.
  •  Tighten the cover with a torque of 15 Nm.
  •  Open the shut-off valves in the heat source flow and the heat pump flow.
  •  Vent the heat source system via the quick-action air vent valve.
  •  After venting, close the quick-action air vent valve.

údržba

  • Clean the filter cartridge if required.

špecifikácia

Rozmery a pripojenia 

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 5

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 7

Pressure drop diagram 

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 6

  • Y Pressure drop [hPa]
  • X Flow rate [1/h]
  • 1 Pressure drop with filter cartridge and strainer
  • 2 Pressure drop with filter cartridge

Tabuľka údajov

STIEBEL ELTRON 233307 WPSF Brine Filling Unit 8

Záruka

The guarantee conditions of our German companies do not apply to appliances acquired outside of Germany. In countries where our subsidiaries sell our products a guarantee can only be issued by those subsidiaries. Such guarantee is only grant­ed if the subsidiary has issued its own terms of guarantee. No other guarantee will be granted. We shall not provide any guarantee for appliances acquired in countries where we have no subsidiary to sell our products. This will not affect warranties issued by any importers.

Životné prostredie a recyklácia

Chceli by sme vás požiadať o pomoc pri ochrane životného prostredia. Po použití zlikvidujte rôzne materiály v súlade s národnými predpismi.

Dokumenty / zdroje

Plniaca jednotka soľanky STIEBEL ELTRON 233307 WPSF [pdf] Návod na inštaláciu
233307, Jednotka na plnenie soľanky WPSF, 233307 Jednotka na plnenie soľanky WPSF

Zanechať komentár

Vaša e-mailová adresa nebude zverejnená.