SINED CAMINETTO-VULTURE-150 Electric Fireplace User Manual
SINED CAMINETTO-VULTURE-150 Electric Fireplace

IMPORTANT: It is important to read these instructions carefully before using the appliance for the first time. Keep the instructions safe so that you can refer to them later if necessary.


  • Rated Voltage: 220-240V~
  • Rated Power: High:1500W; Low: 750W
  • Rated Frequency: 50/60Hz
  • Supply Connection: Non-detachable cord with plug,Type Y attachment

This appliance is intended to be used in household and similar applications such as :

  • staff kitchen areas in shops, offices and other working environments,
  • farm houses,
  • by clients in hotels , motels and other residential type environment,-
  • bed and breakfast type environment
  • areas for communal use in blocks or flats or in launderettes


  1. In avoid to overheating, do not cover the fireplace.
  2. Do not use this heater in the immediate surroundings of a bath , a shower or a swimming pool..
  3. Do not use this heater if it has been dropped.
  4. Do not use if there are visible signs of damage to the heater. The heater must not be used if the glass panels are damaged.
  5. Use this heater on a horizontal and stable surface,or fix it to the wall,as applicable.
  6. Do not use this heater in small rooms when they are occupied by persons not capable leaving the room on their own, unless constant supervision is provided.
  7. Extreme caution is necessary when children are near the fireplace and whenever the fireplace is left operating and unattended.
  8. Always unplug fireplace when not in use.
  9. Do not operate the fireplace with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner, return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
  10. Do not use outdoors. It’s only suitable for indoor use.
  11. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tipped over.
  12. To disconnect fireplace, turn controls to off, then remove plug from outlet.
  13. Do not inset or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the fireplace.
  14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
  15. It has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, or flammable liquids are used or stored.
  16. Use this fireplace only as describes in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
  17. DANGER-HIGH Temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of the heater.
  18. Do not use this heater with a programmer, timer, independent remote control system, or any other device that automatically turns on the heater, because if the heater is covered or incorrectly positioned, there is a risk of fire.
  19. Do not use the Electric fireplace for any other purposes than those described in this instruction manual.
  20. This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  21. Children should be supervised to ensure that they do not play with the appliance.
  22. Do not use this appliance outdoors.
  23. Always unplug the Electric fireplace from the power supply when not in use and before cleaning.
  24. To protect against the risk of electric shock, do not immerse the appliance in water or in any other liquids.
  25. Components should only be serviced by an approved electro technician.
  26. “If the supply cord is damaged, it must be replaced by the manufacturer, its service agentor similarly qualified persons in order to avoid a hazard.”

Cleaning the exterior of the appliance

Before cleaning the appliance, disconnect it from the socket and leave to cool. Do not use cleaning or polishing products.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

Unpacking Operation

  1. It there were nylon packing belts, you need to cut them off.
    Unpacking Operation
  2. After opening the box, take out upper corner protectors and front support plate.
    Unpacking Operation
  3. The product must be handled carefully, in case of damaging the glass.
    Unpacking Operation

Shape and Size (mm)

Shape and Size

Product size list (mm)

Model Length Height


CAMINETTO-VULTURE-150 1500 507 200
CAMINETTO-AMIATA-180 1800 507 200
CAMINETTO-VESUV10-200 2000 507 200
CAMINETTO-ETNA-300 3000 507 200

Installation Instructions

Hole size (Find hole size symbol on product dimensions.)

Note: Support platform need to be flat, complete and firm. Power socket should be connected with ground wire.
Installation Instructions

Functional area on the front:
Installation Instructions

Configuration Information

Product Name Electric Fireplace
Operation mode Manual/Remote control
Rated Voltage 220.240V`
Rated Frequency: 50/60Hz
Viewing Power 10W-300W
Rated Power High:1500W; Low: 750W
Basic Infrared remote control
Manual key
Adjustable flame
Heating function
Single-color flame
Optional Multi-color flame
DIY fake log
Safety Certification CE RoHS
Attachments Remote control
Warranty card

This product has been tested in special electrical room according to national standards. If you need help during use, please contact us in time.

Manual Key Operation

Key Operation






Turn on/off the machine
Symbol Temper

Adjust temperature 19-30°C


Timer Timing: 30min-1h-2h-3h-4h-5h-6h-7h-8h-30min
Symbol Flame

1-6 levels flame

Remote Control Function

Symbols on Remote Control
Remote Control Function

Digital Screen

Digital Screen

Remote Operation

Button Icon On/Off
Press this button to turn on with F1 on screen. Press this button to turn off with nothing on screen.

Button Icon This button no function
Button Icon Adjust flame brightness

Default F1. F1-F2-F3-F4-F5-F6-F1. The number corresponds to flame brightness.


F1 F2 F3 F4 FS F6
Set 1 2 3 4 5



100% 80% 60% 40% 20%


Button Icon Heater (Be off by default)

  1. ”LL” 1-level heater with one iconButton Icon
  2. ”HH” 2-level heater with two icons Button IconButton Icon

Button Icon Temperature rises
The default startup temperature is 19℃. Short press to rise one degree. Temperature cycle: 19-30℃(66-68℉). Long press for 5 seconds to convert temperature units. C(F) can be turned off for heating.

Button Icon Temperature reduces
Short press to reduce 1 degree. Rising to a certain temperature, it will turn off the heating when it rises by 1 degree. Reducing to a certain temperature, it will turn on the heating when it reduces by 2 degrees.

Button Icon Timer
It’s disabled by default. Short pressing will adjust the timer range from 30Min-1H-2H-3H-4H-5H-6H-7H-8H-30Min. The symbol light is on by default.

Button Icon This button no function

Button Icon Day timer
There is a timing function. When turning on the fireplace, the timer icon light will be on. The clock will show 00:00. The week icon light will be on and show SUN.
When the timer is needed after turning on, press “DAY” button on remote control. Each time you press the button, the week icon light will be on from left to right to set the time to the current date.

Button Icon Hour timer
Each time you press the “HOUR” button, the time is increased by one hour. Set the time to the current hour, hour timer scope is: 00-23.

Button Icon Minutes timer
Each time you press the “MIN” button, the time is increased by one minute. Set the time to the current minutes, minutes timer scope is: 00 59. When it is not unplugged or disconnected, the on-off time will have memory function, which will not be reset. If unusual timer id discovered, the batteries powering the mainboard may be dead. Please replace the batteries quickly. (Battery Model: CR1220-3V), (Each time you press the button, the buzzer will make a short sound.)

Button Icon Week timer
It has a week timing switch function.

  1. First press “WEEK TIME” button, the week icon will turn the current time to SUN(Sunday) and flash. The icon of clock and ON will flash at the same time.
  2. Set the startup time of the day. Press “HOUR” button to set starting up hour, press “MIN” button to set starting up minutes. (Each time you press the button, the number will increase 1.) Then press “SET UP” button to confirm. ON light will be off and OFF light will be on.
  3. Set the off time of the day, the process is the same with setting the startup time. After setting for one day, press “WEEK TIME” again to set for another day.
  4. If you don’t operate the week timer during the week display flashes for ten seconds, the clock on the digital screen will be always on. The light of ON/OFF will be off. (Each time you short press the button, the buzzer will make a short sound.)

Button Icon On/Off week timer
Press the button to turn on/off the week timer function.

Button Icon Alarm

  1. Electric fireplace has window opening detection function. When it is in heating state and detects a temperature drop of 3 degrees within 5 minutes, it will turn of heating function automatically. Buzzer will make a long sound three times. The alarm icon light will flash to remind the user that the window has been opened.
  2. After the alarm is on, press the heater or temperature button to clear alarm reminder.

Button Icon This button No function



Probable Causes


Not Work Poor contact between plug and socket Connect the plug correctly or change it
Power is off Turn on
Protector overheats Turn off power, natural cooling for 15min.
Protector overheats and burned out After-sale repairing
Heating without
Lights damage After-sale repairing
Flames without
Heater is off Turn on heater
Remote control not responding Misaligned infrared reception Adjust angles and distance
An internal fuse has blown After-sale repairing
Flames with noise Spark shaft is falling Contact the after-sales service.
Part of the flame is not bright The lamp strip socket is loose or falls off After-sale repairing

Please cut off the power before the maintenance of the appliance. Workers with maintenance qualification are required to avoid accidents and personal injury.

Final Interpretation

The final interpretation right is of our company. Please know if the product appearance and structure are changed, there is no need to inform the user.

Correct Disposal of this product
Dustbin IconThis marking indicates that this product should not be disposed with other household wastes throughout the EU.To prevent possible harm to the environment or human health from uncontrolled waste disposal,recycle it responsibly to promote the sustainable reuse of material resources.To return your used device,please use the return and collection systems or contact the retailer where the product was purchased.They can take this product for environmental safe,recycling.


Produzione: Suzhou Yueyu Thermal Energy Technology Co.
Indirizzo della fabbrica: No. 6 Xinghai Road, Liuhe, Taicang, Taicang City,
Città di Suzhou, provincia di Jiangsu, Cina

Made in China Importato in Italia da M.P.C. srl Via Tortona 20144 Milano Italia Tel +39 02 47758004 e-mail [email protected] sito web

Il marchio SINED e il logo SINED sono registrati da Sined Ventas Online S.L.U. EUTM 018196373

Documents / Resources

SINED CAMINETTO-VULTURE-150 Electric Fireplace [pdf] User Manual

Leave a comment

Your email address will not be published.