Shenzhen Zhixinbao Electronic Technology AX9 Bluetooth Earphone Instruction Manual

Shenzhen Zhixinbao Electronic Technology AX9 Bluetooth Earphone

Thank you for purchasing this product. This product has a stylish appearance and high-quality sound quality. Enrich your life. Please read and strictly follow the instructions and precautions before using this product and keep it properly for future reference.

Reminder:
When you receive this product, please charge it before using it for the first time.

Product illustration

Please fully charge the headset together with the charging compartment before using it for the first time!

Product Description

  1. After opening the charging compartment, take out the earphones and automatically turn on and pair with each other. A single blue light of the earphones flashes. A solid blue light indicates that the pairing is successful. The mobile phone can directly search for the device connection. (Wait 1-3 seconds for the first search) After the headset is placed in the charging compartment, it starts to charge, and the Bluetooth is disconnected at the same time.
  2. A 5V adapter is required to charge the charging compartment and earphones, and it is forbidden to use a voltage higher than 5V for fast charging or or other adapters.
  3. When the headset cannot be charged in the charging compartment, please check whether the charging compartment has electricity, or use a rag. Wipe the charging contacts of the earphones clean and put them in the charging compartment to charge the earphones.
  4. When the headset is abnormal during use, for example, when there is only sound on one side, you can put the two. Only put the headset into the charging compartment for 2-4 seconds to re-pair and then connect.
  5. This earphone has both ears and double hair. After connecting to the mobile phone, turn off one of them, and the other will continue to work.

Bluetooth earphone

  • Bluetooth version: 5.2
  • Headphone battery: 60mAh
  • Continuous play time: about 10h
  • Standby time: 180h
  • Copper ring horn: 10mm

Charging compartment

  • Battery capacity: 400mAh
  • Charging voltage: DC5V
  • Input current: 300MA
  • Output current: 300MA
  • Charging interface: Type-C

Precautions

Please use a device whose output voltage and current do not exceed 5V-1A to charge the headset battery compartment.Do not use fast charging, flash charging, fast charging power bank, etc. Charging, overvoltage and overcurrent charging damage the earphones are man-made damage and are not covered by the warranty.

Warning:
It is strictly forbidden to place this product in a place that is too hot or too cold, the temperature above 50° or below -10° will affect the battery performance.

Multi-function touch button

  • Automatic power on: take out the charging compartment and automatically power on
  • Manual power on: long press for 2 seconds Manual power off: long press for 3 seconds
  • Automatic shutdown: put the headset back into the charging compartment and automatically shut down
  • Reject the call: long press the touch button for 2 seconds
  • Answer/hang up call: click the touch button
  • Play/Pause: Click the touch button
  • Wake up the voice assistant: long press the touch button of any earphone for 2 seconds
  • Switch up and down songs: double-click the left ear for the previous song, double-click the right ear for the next song
  • Volume addition and subtraction: triple-click the left ear volume to decrease, triple-click the right ear volume to increase

Hearing Protection

Do not use it at high volume for a long time to prevent hearing damage.Do not adjust the sound too loudly to prevent hearing surrounding sounds.

Power on/pair/connect the phone

Power on
Open the charging compartment cover, the blue light flashes, it will automatically turn on successfully In the off state, press and hold the left and right touch buttons for 2 seconds to turn on In the power-on state, press and hold the left and right touch buttons for 3 seconds to turn off.

Pair
After opening the charging compartment, take out the headset and pair it automatically, and the single blue light of the headset flashes blinking, another blue light is always on After the earphone pairing is completed, the red and blue flash alternately and quickly enter the mobile phone pairing mode The light goes out after the headset is paired with the phone Headphones light off when working The headset automatically shuts down after three minutes without connecting to a new device in the paired state.

Connect the phone
Open the charging compartment cover, the headset will automatically turn on and pair Open the device, search for the Bluetooth name, and click connect.

If the connection fails, turn off the Bluetooth of the mobile phone and repeat the above operation.

Battery charging

Headphone charging
The red light is always on when the headset is charging Lights off when the headset is fully charged.

Charging bay
When charging the charging compartment, the digital display flashes When the charging compartment is fully charged, the digital display shows 100.

Charging interface Type-C

FCC STATEMENT WARNING

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE 1:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

NOTE 2:
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirements.

Documents / Resources

Shenzhen Zhixinbao Electronic Technology AX9 Bluetooth Earphone [pdf] Instruction Manual
AX9, 2A8AO-AX9, 2A8AOAX9, AX9 Bluetooth Earphone, Bluetooth Earphone

Recent Posts

Dash 2-Pack Mini Waffle & Griddle DMSW002 User Manual

Dash 2-Pack Mini Waffle & Griddle DMSW002 User Manual IMPORTANT SAFEGUARDS PLEASE READ AND SAVE…

8 mins ago

RUKKET Pathfinder Impact Mat Instructions

Pathfinder Impact Mat RukketSports PARTS & SET-UP INSTRUCTIONS 1. Lay out the impact mat and…

13 mins ago

pTron Bassbuds Ultima ANC True Wireless Earbuds User Manual

Bassbuds Ultima ANC True Wireless Earbuds

13 mins ago

SEIFERT 43300001 230V 10240 BTU Control Cabinet Air Conditioner User Manual

43300001 230V 10240 BTU Control Cabinet Air Conditioner Table of Content 43300001 1. User manual…

13 mins ago

OLIGHT X9R CELL Super Tiny Keychain Light Owner’s Manual

X9R CELL Super Tiny Keychain Light X9R CELL SUPER TINY KEYCHAIN LIGHT MAX OUTPUT MAX…

36 mins ago

hameln Remifentanil 1 mg powder for Concentrate for Solution for Injection and Infusion Instructions

Remifentanil 1 mg powder for Concentrate for Solution for Injection and Infusion Remifentanil 1 mg…

37 mins ago