Shenzhen Yuntian Intelligence Control Technology YT-E12Z Zigbee Smart Candle Bulb User Manual
Shenzhen Yuntian Intelligence Control Technology YT-E12Z Zigbee Smart Candle Bulb

Parameters

  • Default setting: warm white+100% brightness +pairing mode
  • Delete the light from app: It flashes 2 times and go to pairing mode
  • Reset the light: Power it off and on(1s) * 5 times The light flashes 2 times
  • Compatible with Zigbee 3.0 hub: Echo(4th)/Echo Plus/ Echo Show(2nd)/ Echo studio… Philips Hue Samsung SmartThings

How to Work with Amazon Alexa?

  1. Confirm the LED indicator of Zigbee bulb is flashing,and the bulb is in power-mode, then you can start to match the bulb with Alexa
  2. Ask: Alexa discover my device”. Then indicator light will flash three times with “ka ka”voice. After that,the indicator will always on.
  3. Wait for the Zigbee bulb LED indicator always on. You will discover the device on your Alexa APP. It means you have connected successful.
  4. Please start to voice control. for example: “Alexa,turn on the first light” Note: you can group,modify device name as “First light,Second light” . then you can ask

How to Work with Philips Hue?

Just add the Zigbee bulb to the Philips App.

How to add?

  1. Click the “Setting”.
  2. Choose “Light setup”.
  3. Auto search,and add successfully.
  4. Waiting new device shows up, modify the name. Note: you can adjust the colors, brightness on app.

How to Work with Samsung SmartThings?

Please follow the steps:

  1. Please set the smart bulb into an outlet.
  2. Open SmartThings App, and click”+”.
  3. Click “By brand”and choose “eWeLink”.
  4. Choose “Light” and follow the on-screen tip to go on.

Customs Service

12-month limited warranty lifetime technical support
Email: [email protected]
(For any inquires or comments concening to this product, please contact the seller).
We appreciate your support!

Warm Tips:

  1. The device is for indoor use only.
  2. The device should not be exposed to splashing water or any danger sources.
  3. Do not use this device with dimmers.
  4. Do not use this device in totally enclosed luminaires. Use this device in open luminaier only.
  5. Do not install near any heat sources.

RISK OF ELECTRIC SHOCK: USE IN LOCATIONS ONLY. DO NOT INSTALL THIS DEVICE WITH WET HANDS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Documents / Resources

Shenzhen Yuntian Intelligence Control Technology YT-E12Z Zigbee Smart Candle Bulb [pdf] User Manual
YT-E12Z, YTE12Z, 2A6NY-YT-E12Z, 2A6NYYTE12Z, YT-E12Z Zigbee Smart Candle Bulb, Zigbee Smart Candle Bulb

Leave a comment

Your email address will not be published.