Wireless Charger
User Manual

Shenzhen Luxneon EGC71 Wireless Charger

 

Shenzhen Luxneon EGC71 Wireless Charger certi

Made in China

Product Introduction

Thank you for purchasing this product! This product is a folding wireless charger stand with a simple and generous design, suitable for devices that support the QI standard. Provide you with a convenient, fast, safe and free wireless charging experience.

Product Appearance

Mobile phone charging area

Shenzhen Luxneon EGC71 Wireless Charger A

EGC71
Wireless Charger

Method Of Use

Shenzhen Luxneon EGC71 Wireless Charger A Error 1

Error

Shenzhen Luxneon EGC71 Wireless Charger A Error 2

Error

Shenzhen Luxneon EGC71 Wireless Charger A Correct 1

Correct

Model

State

EGC71
Power connected Red & blue on for 1s and then off
Standby Red light
Phone charging Blue light
Earphone Charging /
Watch Charging /
FOD – phone Blue light flashing
FOD – earphone /
Product Parameter

Product name: Wireless Charger
Model: EGC71
Input: 5V/2A 9V/2A 12V/1.5A
Phone output: 5W/10W/15W
Product size (flatwise): 156*75*22mm

Instructions
  • Stand up the phone charger pad, the user can freely adjust the required angle.
  • Plug in the equipped Type-c cable and turn on the power.
  • Place the device supporting Qi standard in the center of the charging area to start charging.
  • The 2-in-1 wireless charger is suitable for charging mobile phones and AirPods Pro.
  • The 3-in-1 wireless charger is suitable for charging mobile phones and AirPods Pro, Apple Watch.
Accessory List

Wireless Charger*1
1m Type-c cable*1
User manual*1

Matters Needing Attention

※Do not disassemble this product by yourself.
※Please do not use this product in high temperature or humid environment, please keep away from fire and water.
※Please use the original charging cable of this product to ensure that the wireless fast charging function is normally turned on.
※This product is only suitable for charging devices that support wireless charging.
※If the mobile phone has no built-in wireless receiving function, please purchase a wireless charging receiver separately for use.
※If the mobile phone does not support the wireless fast charging function, it will automatically adjust to the charging efficiency of the mobile phone itself.
※The charging contact surface on the back of the charging device must not contain metal materials, such as iron sheets, finger rings, metal protective shells, etc.
※It is recommended to use QC3.0/PD power adapter. Can make the efficiency of wireless charging achieve better results.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Documents / Resources

Shenzhen Luxneon EGC71 Wireless Charger [pdf] User Manual
EGC71, 2A7FW-EGC71, 2A7FWEGC71, EGC71 Wireless Charger, Wireless Charger

Leave a comment

Your email address will not be published.