Shenzhen Bling Lighting Technologies LDD-25W-C Smart Floor Lamp User Manual

user manual

Smart floor lamp user manual

Thank you for your choice. Please read the user manual carefully and keep it for future reference.

Correct installation is required, please follow the instructions step by step. After installation, this smart floor lamp can be controlled by APP or touch-sensitive button on the lamp.

Specification
Model LDD-25W-C / LDD-25W-D
Wattage 25W
Dimension Ø25x 168cm
Input Voltage 100-240V AC, 50/60Hz
Color Temperature 2700K-6500K
Max Luminous Flus MAX. 2000 lm
Beam Angle 160 deg
Protection Rating IP20
Controlled By Voice/APP/Touch
Color 2700K-6500K White+ RGB
Material Plastic; Cast iron hardware
Before Assembly
  1. Inspect lamp before beginning assembly. Wire connections have been made at the factory and the lamp is ready for assembly.
  2. Remove all packing materials from the lamp.
  3. To prevent bad connections, avoid pulling wiring connections when removing contents from package or during installation.
  4. Lay out all the parts on a flat surface.
  5. The floor lamp consists of seven parts:1xLamp Head, 4xPole,1xLamp Base, 1xElectric Wire with Adapter(Refer to illustration).
Assembly Instruction
  1. Place the lamp base on flat surface, then screw each two parts clock-wise in order.
    Note:
    • Please take care not to pinch or damage the wires.
    • For better installation, please tighten the bottom pole and lamp base firstly.
    • Make sure each section of tubes are tightened.
  2. Plug adapter into outlet and now the lamp is ready for use.

Adjustment
For best performance, please adjust the lamp position to directly above your area of reading/working.

30° up/ down adjustable

JP            US           EU         UK

 

PART One : Download the App

Step A: Smart Life app installation
Please choose either way below to download and install the app.
1. As per your phone system, choose the QR code to scan.

   

iOS                      Android

2. Search keyword ‘Smart Life’ in Apple Store or Google Play.

Step B: Create an account on Smart Life and login.
Note: Please keep your account and password in mind for Alexa or Google Assistant App pairing later.

Part Two: Pair the smart floor lamp to “Smart Life” App

1. TURN INTO PAIRING MODE (2 options)
> Short touch the Power button 5times (ON/OFF/ON/OFF/ON), the lamp will flash rapidly and then flash slowly 3 times.

> Long touch the Power button for 5 seconds, the lamp will flash rapidly and then flash slowly 3 times.

NOTES: the lamp will automatically drop out pairing mode if no any mobile devices connected within 5 minutes.

Connect the mobile phone to WIFI Open the smart life app Select add device Select add lighting Select lighting WIFI Enter the WIFI password Waiting for the show successfully

If you want to explore AP Mode, you can tap ‘AP Mode’ on top right corner, and follow the detailed instructions by tapping ‘view help’ on the next page.

Part Three – How to control the light with Amazon Alexa?

Please make sure that your Alexa app is connected to Echo, and both work well under your WiFi network.
Step A: Log in your Alexa App, tap top left corner, and tap ‘skills’.

   

Step B: Type ‘Smart Life’, find ‘Smart Life’ from the search result and tap it to enable the skill.

   

Step C: Enter your Smart Life App account and password. Tap ‘Link Now’, then tap ‘Authorize’ on the next page to bind Smart Life account to Alexa.

Step D: When your Smart Life account is bound to Alexa, tap ‘DISCOVE DEVICES’ to detect the light.

Step C                                         Step D

Step E: When the named light is paired to Alexa from Smart Life, it will show on the device page (see the ‘smart light’ example).

Step F: Now you can control the light with Alexa App on the setting page. To turn on or off the light, simply tap the bulb icon.

Step G: You can also voice control the light with Alexa by giving these commands: “Alexa, turn on ‘device name’ “, “Alexa, set ‘device name’ to ‘color’ “, “Alexa, set ‘device name’ to ‘number’ “. Device name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “Alexa, turn on ‘smart light’ “, “Alexa, set ‘smart light’ to ‘blue’ ” etc.

     

Note: To control the light with Google Assistant, please continue to read Part Four.

Part Four – How to control the light with Google Assistant?

Step A: Login Google Assistant App, tap ‘Home Control’ on the left side bar page.
Step B: Tap ‘+’ button on the bottom right to enter next page.
Step C: Find ‘Smart Life’ from side bar list.

   

Step D: Enter your Smart Life App account and password to bind Smart Life account to Google Assistant.

Step E: You will find the named light shows on the Home Control page. Now you can control the light on Google Assistant App, or voice control it by giving these commands. “ok Google, turn on ‘device name’ “, “ok Google, set ‘device name’ to ‘color’ “, “ok Google, set ‘device name’ to ‘number’ “.

Device name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “ok Google, turn on ‘smart light’ “, “ok Google, set ‘smart light’ to ‘blue’ ” etc.

Step D                                   Step E

      

Key Function

Power button
1. Short touch: Power ON or OFF 2. Long touch: Pairing.

Light button
1. Short touch to switch color 2. long touch to dim brightness.

Short press Light Brightness Function
1 white 50% long press 1s to adjust the brightness
2 warm 50%
3 blue 50%
4 green 50%
5 red 50%
6 pink 50%
7 orange 50%
8 purple 50%
9 party 50%
10 fade 50%

5V/1A provided by USB
Do not exceed the Max. output 5V/1A, or it will cause the buttons out of work.

WARNING:

    Cut off the power before installation.
   Keep it away from flammables and fire source.
  Replacing and clean to avoid electricity touched.
  Lamp is operated in dimming circuit
  Keep it away from water.
   Assemable the lamp according to the instructions and do not rebuild.
Do not stare at the lamp for a long time.
  Assemble, take apart or move the lamp gently.
  Please do not cover anything on the lamp head and avoid bending and bumping the lamp pole.
Keep it away from children.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Documents / Resources

Shenzhen Bling Lighting Technologies LDD-25W-C Smart Floor Lamp [pdf] User Manual
LDD-25W-C, LDD25WC, 2AI5T-LDD-25W-C, 2AI5TLDD25WC, LDD-25W-C Smart Floor Lamp, Smart Floor Lamp

Recent Posts

INDESIT ID67V9KMW 60cm Double Oven Electric Cooker Installation Guide

ID67V9KMW 60cm Double Oven Electric Cooker ID67V9KMW/UK ID67V9KMB/UK ID67V9HCCX/UK EN ENGLISH Health and Safety guide…

2 mins ago

Zoom F1-LP Lavalier Body-Pack Recorder-User Manual

Zoom F1-LP Lavalier Body-Pack Recorder

4 mins ago

ZALMAN S4 Plus, S4 Plus TG ATX Mid Tower Case User Manual

S4 Plus, S4 Plus TG ATX Mid Tower Case S4 S4 Plus Plus TG User's…

10 mins ago

Royal Gourmet GD4002T Tailgater Grill and Griddle Combo Owner’s Manual

GD4002T Tailgater Grill and Griddle Combo

12 mins ago

Rollei L-Winkel / L-Bracket Refrigerator Instruction Manual

L-Winkel / L-Bracket Refrigerator L-Winkel / L-Bracket BEDIENUNGSANLEITUNG IN DEUTSCH INSTRUCTION MANUAL IN ENGLISH www.rollei.de…

17 mins ago

LED s light 1000424 Solar Table Lamp Instruction Manual

1000424 Solar Table Lamp LED's light OUTDOOR SERIES NI-MH 1,2 V 500 mAh 0,6Wh Incl.…

24 mins ago