SEALEY-LOGO

SEALEY HT300R SMD LED Rechargeable Headlight

SEALEY-HT300R-SMD-LED-Rechargeable-Headlight-PRODUCT

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

GENERAL SAFETY

  • DO NOT shine directly into your, another person’s, or an animal’s eyes.
  • DO NOT allow children to use the torch.
  • DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
  • DO NOT leave batteries in a discharged state. Before storage remove batteries and dispose of them in the correct manner.

BATTERY SAFETY

  • WARNING: To reduce the risk of burns or fire:
  • DO NOT attempt to open the battery.
  • DO NOT crush, puncture, short contacts, or dispose of in fire or water.
  • DO NOT expose to temperatures above 60°C (140°F).
  • If the electrolyte in the batteries gets on your skin, thoroughly rinse with water. If it gets in your eyes, rinse thoroughly with cool water and seek immediate medical attention.

INTRODUCTION

3W COB + 1W SMD Rechargeable headlight with sensor function. Also includes 3 SMD LEDs producing 300 Lumens. Can also act as a separate mini work light with a magnet. 3.7V 1200mAh Li-Poly battery with 0.3m USB cable included. Charging and battery indicator capabilities. 4hr maximum runtime using COB.

SPECIFICATION

  • MODEL NO:…………………………………………………… HT300R
  • Battery: ……………………………. 3.7V 1200mAh Li-Poly Battery
  • Charging Time:…………………………………………………….3-4hrs
  • LED Qty: ………………………………………………….1 COB 3 SMD
  • LED Type: …………………………………………………. COB + SMD
  • Lumen Output: ……………………………COB-150lm SMD-300lm
  • Operating Time: …………………………………. COB/SMD 4hr/2hr

OPERATION

TORCH OPERATION

SEALEY-HT300R-SMD-LED-Rechargeable-Headlight-FIG-1

  1. Press the power button (fig.1) once to turn the unit on.
  2. The battery charge state is indicated by the 4 blue LEDs
  3. Press the power button again to light the primary light
  4. Press the power button again to also light the secondary light
  5. Press the power button again to turn the unit off.

LIGHT SENSOR

  1. Press the sensor button (fig.1) to enable sensing.
  2. Pass hand in front of the light until the light comes on.
  3. Pass hand in front of the light again and the light goes off.
  4. Press the sensor button (fig.1) to disable sensing.

TILTING HEAD

  1. The headtorch has 4 possible lockable positions, 00, 200, 400, and 600

DISMOUNT TORCH

  1.  Twist the light unit through 450 to remove it from headband mounting.

MAINTENANCE

  • CHARGING: Connect the USB lead to the port on the side of the unit and to a USB power supply socket on the other.
  • Keep the torch clean by wiping it with a damp cloth.

Documents / Resources

SEALEY HT300R SMD LED Rechargeable Headlight [pdf] Instructions
HT300R, SMD LED Rechargeable Headlight, HT300R SMD LED Rechargeable Headlight, LED Rechargeable Headlight, Rechargeable Headlight, Headlight

References

Leave a comment

Your email address will not be published.