User Manual for Cell2 models including: MSP15HM Dual Level Multi Function Warning Light, MSP15HM, Dual Level Multi Function Warning Light, Multi Function Warning Light, Function Warning Light, Warning Light
MSP Combo - SC - Top White - Bottom White - Cell2
Feu MSP - 30 30 LEDs - Multifonction - Orange/Bleu/Rouge
DUAL LEVEL MULTI-FUNCTION WARNING LIGHT Manual 86-M08810-0101.0 Wiring Default Setting Chart BLACK -------- to Chassis ground === UPPER LEVEL === -------- [+] (fuse @ 0.5A) Steady-burn Low Power [P2] BROWN ------ [+] (fuse @ 0.5A) Steady-burn High Power [P1] === LOWER LEVEL === RED -------- [+] (fuse @ 3A) Warning Mode 1 [P4] ORANGE ------ [+] (fuse @ 3A) Warning Mode 2 [P4] Warning Mode 3 [P3] GREEN ------ [+] (fuse @ 3A) Warning Mode 4 [P2] BLUE -------- [+] (fuse @ 3A) Low Power or [+] Warning Mode 5 [P1] (See "WARNING MODE 5 SETTING" for Blue Wire) YELLOW ------ For Setting, Synchronisation and Flash Pattern [+] Connect YELLOW wires of all lightheads together for synchronisation. NOTE: (All lightheads should be set to the same Flash Pattern) [+] = Activate the wire function by applying constant +VDC to the wire. [Px] = Precedence order, when more than a wire is activated at the same time, higher precedence wire will affect lower precedence wire. P1 being the highest priority. Operation For Flash Pattern Selection: Each Warning mode may select and save one flash pattern. While activating a warning mode, momentarily apply YELLOW wire to +VDC: · once to the next pattern. · quickly three times to FP#1. Shortcut Setting for Steady EF (External flasher): This shortcut allow changing all trigger wires to its default color mode and Steady EF pattern at the same time. While activating any warning mode, momentarily apply YELLOW wires to +VDC for more than 4 seconds. (Visual feedback ONOFFON) COLOUR & PATTERN Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Single Colour Model Default Colour Default Pattern Colour1 35. Steady Cruise Colour1 1. Double Colour1 1. Double Colour1 19. MINI TA LEFT Colour1 26. MINI TA RIGHT COLOUR & PATTERN Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Dual Colour Model Default Colour Default Pattern Colour1 35. Steady Cruise Colour1 1. Double Colour1 1. Double Colour2 19. MINI TA LEFT Colour2 26. MINI TA RIGHT COLOUR & PATTERN Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Tri Colour Model Default Colour Default Pattern Colour1 35. Steady Cruise Colour1 1. Double Colour2 19. MINI TA LEFT Colour3 18. Steady High Colour2 26. MINI TA RIGHT FP# Flash Pattern 1 Double [2HZ] 2 Single [2HZ] 3 Triple [2HZ] 4 Quad [2HZ] 5 Random 6 Steady EF 7 Single [SAE/CA13] 8 Double [SAE] 9 Triple [SAE] 10 Quad [SAE] 11 Quint [SAE] 12 Mega 13 Giga 14 Ultra [SAE] 15 Single-Quad 16 Single H/L 17 Single-Triple-Quint 18 Steady High 19 MINI TA LEFT SWEEP 20 MINI TA LEFT SOLID 21 MINI TA LEFT SWEEP - Left Side of a pair 22 MINI TA LEFT SOLID - Left Side of a pair 23 MINI TA LEFT SWEEP - Right Side of a pair 24 MINI TA LEFT SOLID - Right Side of a pair Available Colour Mode Remark S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T For use with an external flash controller S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T When using as a pair of units S / D / T When using as a pair of units S / D / T When using as a pair of units S / D / T When using as a pair of units FP# Flash Pattern 25 Steady Mid 26 MINI TA RIGHT 27 MINI TA RIGHT SOLID 28 MINI TA RIGHT SWEEP - Left Side of a pair 29 MINI TA RIGHT SOLID - Left Side of a pair 30 MINI TA RIGHT SWEEP - Right Side of a pair 31 MINI TA RIGHT SOLID - Right Side of a pair 32 Steady Low 33 MINI TA CENTER-OUT 34 MINI TA CENTER-OUT SOLID 35 Steady Cruise 36 Sweep Single TA 37 Turn Indicator [ECE Amber / SAE Red] 38 Turn Indicator [SAE Amber] 39 OFF 40 Single-Single 41 Double-Double 42 Triple-Triple Mid 43 Triple-Triple Fast 44 Quint-Triple 45 7-1 Flash 46 Quad-Single 47 Quint-Quint Available Colour Mode Remark S / D / T S / D / T S / D / T S / D / T When using as a pair of units S / D / T When using as a pair of units S / D / T When using as a pair of units S / D / T When using as a pair of units S / D / T S / D / T S / D / T S / D / T S / D / T S / D / T For use with an Intermittent flash signal with OFF delay S / D / T For use with an Intermittent flash signal with OFF delay S /D /T D D D D D D D D S = Single Colour D = Dual Colour T = Tri Colour Setting Mode Each Warning mode may select and save its Colour Mode and Flash Group. Power down the unit then apply +VDC to a Warning Mode function wire (RED or ORANGE or RED&ORANGE or GREEN or BLUE) and YELLOW wires simultaneously then remove YELLOW wire to enter SETTING MODE for the following settings. Save and exit the setting by disconnecting the power. For Colour Mode Setting: Momentarily apply YELLOW wire to +VDC for less than 1 seconds to change colour and order. Please refer to the Colour Mode table. NOTE: For Single and Dual Colour Model, only limited modes are available. For Simultaneous or Alternating Synchronisation: To change Group, momentarily apply YELLOW wire to +VDC for more than 3 seconds. Display of the lighthead: · Single flash = Group 1 (Simultaneously) · Double flash = Group 2 (Alternately) NOTE: Lightheads of the same Group will flash together; lightheads of the Group 1 & Group 2 will flash alternately. Reset to Factory Default Settings: Apply to +VDC for more than 5 seconds. The lighthead will display fast short flashes to signify restoring successfully. Warning Mode 5 Setting By default, BLUE wire functions as Low Power operation. However, it is possible to set BLUE wire function as an extra Warning Mode 5. To config, power down the unit, apply +VDC to a wire and YELLOW wires simultaneously then remove YELLOW wire to enter WARNING MODE 5 SETTING MODE. Momentarily apply YELLOW wire to +VDC for less than 1 second to change its setting. Once set, exit the setting by disconnecting the power. · Steady Low = Low Power Operation (Default) · Steady High = Warning Mode 5 . Colour Mode 11 22 33 41 2 52 1 62 3 73 2 81 3 93 1 10 1 2 3 11 1 3 2 12 2 1 3 13 2 3 1 14 3 1 2 15 3 2 1 Single flash Low Power Steady Surface Mount Template 1:1 Scale L-Bracket Mount 171.6mm (6.75inch) 128.18mm 256.36mm Ø13 Surface Mount Mounting Screw (M3x10mm) Set torque force @ 6.5 kgf-cm (36.4 lbf-in) OR Mounting surface (0Ø.5195imncmh) 256.37mm (10.1inch) Mounting Screw (4*15mm) Mounting Foam L-Bracket Mounting Screw (M3x10mm) Set torque force @ 6.5 kgf-cm (36.4 lbf-in) Bail (U-Bracket) Mount OR 130~150mm (5.1~5.9inch) U-Bracket (Sold Seperately) Flat Washer Spring Washer Mounting Screw (3/16x1-1/4) L-Bracket Mounting Bolt (M3x16mm) Set torque force @ 6.5 kgf-cm (36.4 lbf-in) 128.18mmAdobe PDF library 17.00 Adobe Illustrator 28.3 (Windows)