Water Regulations Approval Scheme Ltd - Approvals Directory
HomeGuarantees
User Guide for BRISTAN models including: SPR EFSNK BB D2 Easy Fit Tool, SPR EFSNK BB D2, Easy Fit Tool, Fit Tool, Tool
Bristan Spruce Easyfit Kitchen Sink Mixer Brushed Brass SPR EFSNK BB
14 hours ago —
19 hours ago — & User Guide. Please leave these instructions with the end user. Product Code: SPR EFSNK BB (D2). If the surface the tap is being fitted to is over 8mm; or ...
File Info : application/pdf, 2 Pages, 3.90MB
DocumentDocumentInstallation Instructions & User Guide Please leave these instructions with the end user Product Code: SPR EFSNK BB (D2) Specifications Dynamic Water Pressure Inlet Water Temperature Min: 0.3 bar Max: 5.0 bar 2.0 3.0 1.0 4.0 65°C Inlet Connections 1/2" BSP Flexible Tails with Isolation Valves Outlet 0 5.0 Pressure BAR Maximum Static Pressure: 10.0 bar Maximum Hot 65°C Tools You'll Need Non-Return Valves Included Spare Parts M24 Aerator Adjustable Spanner EasyFit Tool 2.5mm 6mm Hexagonal Key Crosshead Screwdriver To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product. Prior to Installation Pack Contents All products manufactured and supplied by Bristan are safe provided they are installed, used correctly and receive regular maintenance in accordance with these instructions. This product has been tested to the Water Regulations Advisory Scheme (WRAS) and satisfies the requirements of the Water Supply (Water Fittings) Regulations 1999 and current bylaws. For full Installation Requirements & Notes (IRN) please visit wras.co.uk/directory. Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance. Before installing these taps the water supply must be thoroughly flushed in order to remove any swarf, solder etc. This product must not be modified in any way as this will invalidate the guarantee. Flexible Connecting Pipes Slight bend 90° angle Curved round Kinks Twists x1 x1 x2 x1 x1 x2 x1 x2 x1 x1 x1 Installation 1 2 Remove the protective cap from the base assembly. Feed the base through the sink hole from the top. 8mm REMEMBER wbhaestMhenteahivskefierecotwesannupettrderoafftlrihoseemd y Ensure flat area of the plain inlet connector is sitting flush adjacent to threaded inlet connector If the surface the tap is being fitted to is over 8mm; or you feel the tap needs extra stability, follow the Drop the Plain Inlet alternative installation steps overleaf. Connector into x the base. 3 4 leRthfhEtoe,MtcrEooignMldhBttohEneR 5 Connect the hot and cold water connections. Turn the hexagonal key clockwise until the base is secured. Screw the flexible tails into the base. DO NOT OVER-TIGHTEN Olive Hand tighten Compression Nut 6.0 mm 6 7 Place your 8 desired tap onto the base. Grease the O-Rings using the Molykote Grease provided. 9 Thread the hexagonal key through the EasyFit tool and tighten the grub screws with an extra 1/2 turn fputaloltypIshMEilteionsPiocsbOcnuaaoRertsreedTerdeAtahcoNnetndlTy Secure in place with the grub screws using the tool provided. 6.0 mm Your tap is now ready to use. General Cleaning Operation - Eco-Start Bristan products are made from premium materials, with hand polishing and electroplated finishes. Your taps or shower should be regularly cleaned with warm water, a mild pH-neutral liquid soap, and polished with a soft cloth. Any residues from soap, toiletries etc. should be rinsed off straight after use. Household bleaches and cleaners contain harsh chemicals and may damage the surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar. Some surfaces such as nickel and pewter may be affected by the dye found in some cloths, so it is also important to avoid hanging cloths on spouts. Starting temperature is cold. The temperature will gradually rise the further the rotation of the handle. Once the handle ceases to turn, it will be supplying the On maximum temperature. Increase temperature Alternative Installation for Surfaces Out of Tolerance/Extra Stability 1 2 3 REMEMBER Turn the hexagonal key anti-clockwise to remove the back nut from the EasyFit Base. Make sure the base is centralised when viewed from the front of the tap Feed the base through the 6.0 mm sink hole from the top. Feed the Reinforcing Plate (if required) and Back nut up to the underside of the sink. 4 5 6.0 mm 4 Maintenance - Cartridge Removal/ Replacement 1 2.5 Remove the handle and 2 shroud. Unscrew the retaining nut and remove cartridge. 5 mm IMPORTANT Isolate the water supply before starting! 3 Scan the QR Code and search for your product code to replace the cartridge for your tap. 4 12 Reverse the steps to replace the valves and handles. Turn on the mains water supply, letting the water flow for a few minutes to flush through the system. Troubleshooting Symptom Cause(s) Remedy Partially closed isolation valve. Open isolation valve. Head of water is below the minimum distance required. Hot or cold water being drawn off elsewhere No flow or low causing pressure changes or instantaneous flow rate boiler temperature changes. Airlock or partial blockage in the supply pipework or hoses. Refer to your specification for the minimum working pressure/ distance required Do not use other water outlets when using the taps. Flush through pipework to ensure removal of debris and any airlocks. Water supply failure Investigate water supply. Check your plumbing and heating systems for any faults. Water dripping from taps This is normal for a short time after using the taps. If water continues to drip, possibly due to the ceramic disc valves/cartridge This is caused by residual water tension, the build up of water in the tap body. Refer to the Maintenance section to replace the valves/ cartridge. Turn the hexagonal key clockwise to secure the EasyFit Base. Maintenance - Cleaning/Replacing Outlet 1 2 Unscrew the aerator using M24 outlet key. Remove the aerator from the spout. Clean and replace as necessary. Proceed to Step 4 of the Installation Steps. 3 Secure the aerator. Turn on the mains water supply, letting the water flow for a few minutes to flush through the system. Taps do not turn on Closed isolation valve. Mains water supply turned off. Open isolation valve. Turn on mains water supply. Contact Us Bristan Group Ltd. UK: Bristan Group, B78 1SG. EU: Masco Europe S.à.r.l. 14 Rue Strachen 6933 Mensdorf Luxembourg Customer Service: +44330 026 6273 Web: Email: www.bristan.com enquire@bristan.com A Masco Company At Bristan, we want to make things as easy as possible for our customers. That's why we offer solid guarantees on all our products, effective from the date of purchase, to give you peace of mind. To start your free guarantee simply scan the QR code and register your product. Alternatively visit www.bristan.com/register. For any other queries, please call our Customer Service on 0330 026 6273 where our expert team of advisors will be able to offer you any help and advice. For full guarantee terms and conditions visit www.bristan.com/guarantees.