User Guide for HOLMAN models including: WS3038, Foresight Pro Weather Analyst Weather Station, Analyst Weather Station, WS3038, Weather Station, Station
Instruction Manuals - Holman Industries
Foresight Pro Weather Analyst Weather Station - Holman Industries
P R O W E A T H E R A N A LY S T User Guide1of8 2019 Contents Introduction3 Tech Specs 3 Indoor Display Console 3 Outdoor Sensor 3 Overview4 Main Console 4 Setup5 Initial Operation 5 Mounting the Outdoor Sensor 5 Manual Time Setup 5 Daily Alarm Setup 5 Daily Alarm ON/OFF 5 Snooze Function 6 12/24hr Mode 6 °C/°F Temperature Display 6 Max/Min, In/Outdoor Temperature and Humidity 6 Temperature Alert Setup 6 Temperature Alert ON/OFF 6 Sunrise/Sunset and Moonrise/Moonset 6 Weather Forecast 6 Barometer Graphic and 12hr History 6 Altitude and Weather Icon Selection 7 Illumination7 Moon Phase Display 7 Living Space Humidity 7 Freeze 7 Low Battery Condition Display 7 Wireless Connection to Outdoor Sensor 7 City Locations 8 2 of 8 Introduction Thanks for choosing our Foresight Pro Weather Analyst. Please read this user guide carefully to familiarise yourself with the features and modes of operation before using the instrument. Tech Specs Indoor Display Console 6 buttons: MODE, +, -, HISTORY, CHANNEL, SNOOZE/LIGHT, Time display in 12/24 format Continuous perpetual calendar up to 2099 Display of Date, Month and Day of Week Dual alarm with snooze function (5 minutes alarm interruption) 5× weather forecast: Sunny, Partly Sunny, Cloudy, Rainy, Stormy Comprehensive barometer with graphic bar and 12-hour history for air pressure Altitude-setting for calculation of air pressure Dual indoor and outdoor readings Temperature and humidity with trend Max/min of temperature and humidity Thermometer measuring range: Inside: 0~+50°C, Outside: -20~+60°C Temperature display elective in °C or °F Outdoor temperature alert Freeze will be displayed in case of outdoor temperature under -1.1 °C Moon phase Sunrise and sunset / moonrise and moonset for 176 cities Low battery indication Blue back-light on LCD display Requires batteries: 3× AAA, LR03, 1.5V Outdoor Sensor Frequency: 433 MHz, 3× channels Transmission distance: 50m in open area Batteries: 2× AAA, LR03, 1.5V Must sit at least one meter above the ground 3 of 8 Overview Main Console A. MODE B. + C. D. HISTORY E. CHANNEL F. SNOOZE/LIGHT G. Battery compartment G H. Base stand H 1. Freeze 2. Weather 3. Indoor Low Battery 4. Air Pressure Trend 5. Outdoor Low battery 6. Temperature Alert 7. Indoor Max/Min 8. Outdoor Max/Min 9. Indoor Temperature 4 of 8 10. Outdoor Temperature 11. Outdoor Temperature Trend 12. Indoor Temperature Trend 13. Outdoor Humidity Trend 14. Outdoor Humidity 15. Indoor Humidity Trend 16. Indoor Humidity 17. Living face 18. Week 19. Day of Week 20. Alarm 21. Time 22. Month 23. Date 24. Moonrise 25. Moonset 26. Cities 27. Sunset 28. Sunrise 29. Moon Phase 30. 12hr history of Pressure 31. Air Pressure 32. Bar of Air Pressure Setup Initial Operation 1. Open the battery compartment located on the rear side of the devices. Place the batteries in the battery compartment. Observe the shown polarity. 2. Altitude will be flashing. Use + and to set the altitude of your position. Press HISTORY to confirm 3. The weather symbol will now be flashing. Use + and to choose the weather. Press HISTORY to confirm Mounting the Outdoor Sensor We suggest the outdoor sensor to be hung as shown. It is best not to stand it loose outdoors. Avoid direct sun shine or rain as much as possible. Manual Time Setup 1. Press and MODE for 3 seconds 2. The display for Year is flashing. Use + and to select the current year. Press MODE to confirm 3. The display for Month is flashing. Use + and to select the current month. Press MODE to confirm 4. The display for Date is flashing. Use + and to select the current date. Press MODE to confirm 5. The display for 12/24hr time is flashing. Use + and to choose between 12 and 24hr time. Press MODE to confirm 6. The display for Hour is flashing. Use + and to select the current hour. Press MODE to confirm 7. The display for Minutes is flashing. Use + and to select the current minute. Press MODE to confirm 8. COUNTRY/CITY flashing. Use + and to select our location. Press MODE to confirm The clock automatically changes from setup mode to time display if nothing is pressed for 20 seconds 4. Now hPa flashing. Use + and to choose between hPa and inHg 5. The Indoor Display Console is now connecting to the Outdoor Sensor. This process takes about 3 minutes, then the display shows the outdoor temperature and humidity. In case of failure of reception, press CHANNEL for more than 3 seconds to receive again Daily Alarm Setup 1. Press MODE to switch from time display to A1 display 2. Press and hold MODE for 3 seconds. The flashing alarm time will be shown 3. The hour display of the alarm time is flashing. Use + and to select the hour needed. Press MODE to confirm 4. Follow on with the minutes. Use + and to select the minuted needed. Press MODE to confirm 5. Press MODE again to switch from A1 to A2 display, then repeat steps 2-4 to set the A2 alarm time Daily Alarm ON/OFF 1. When showing A1 alarm time, press to activate alarm A1 with alarm symbol showing 2. Press again to cancel the alarm 3. When showing A2 alarm time, press to activate alarm A2 with alarm symbol showing 4. Press again to cancel the alarm Alarm A1 is for Monday to Friday Alarm A2 is for Saturday to Sunday The alarm sounds for 2 minutes if no key is pressed to stop it. 5 of 8 Setup (continued) Snooze Function 1. Press SNOOZE/LIGHT while the alarm sounds to activate the snooze function 2. If the snooze function is activated, the alarm symbol will be flashing 3. The alarm will repeat after 5 minutes 4. The snooze function can be stopped by pressing any key 12/24hr Mode The time display can be in 12hr (AM/PM) or 24hr mode °C/°F Temperature Display The temperature display can be in °C or °F. In Normal Mode, press to switch between °C or °F Max/Min, In/Outdoor Temperature and Humidity Press + for displaying of Indoor/Outdoor Max/Min of temperature and humidity Temperature Alert Setup 1. Press CHANNEL to select the channel (CH1, CH2, CH3) if more than one outdoor sensor are within reaching 2. Press and hold the key in the area of outdoor, select ON/OFF when flashing 3. Press MODE, the upper limit temperature is flashing, use + and to set the maximum alert temperature 4. Press MODE again, the lower limit temperature will be flashing, use + and to set the minimum alert temperature 5. When the alert is activated, the alert symbol will be shown Temperature Alert ON/OFF Press and hold to set the temperature alert on or off. Temperature alert symbol will indicate if alert is on or off A temperature alert can be set-up for each channel The setup process cannot be completed if the maximum temperature selected is lower than the minimum selected temperature The minimum temperature selected must at least be 1°C below the maximum selected temperature Sunrise/Sunset and Moonrise/Moonset There will be 176 cities' time for Sunrise/Sunset and Moonrise/Moonset. See back page for list of Australian and New Zealand locations available Weather Forecast SUNNY PARTLY SUNNY CLOUDY RAINY STORMY Weather is forecast by barometer only, so the display will have discrepancy with the actual weather sometimes Barometer Graphic and 12hr History Air pressure can be in hPa and inHg, and you can check the past 12hr air pressure by pressing HISTORY 6 of 8 Setup (continued) Altitude and Weather Icon Selection 1. Hold HISTORY for 3 seconds, there will be altitude flashing, you can adjust this altitude 2. Press HISTORY, the weather icon will flash, press + and to select weather icon 3. Press HISTORY, the hPa will flash, press + and to switch between hPa and inHg. The reading will be comparative air pressure. If altitude is set to 0, the reading will match local air pressure Illumination Press SNOOZE/LIGHT to activate the display illumination for 5 seconds Moon Phase Display Living Space Humidity The weather station uses saved data to determine the humidity in the living space and shows the respective symbols: Smile Meh frown Dry: humidity below 40%, any temperature Comfortable: humidity 40%~70%, temperature 20~28°C Wet: humidity 70%~90%, any temperature Freeze The freeze symbol SNOWFLAK will flash in case outdoor temperature at range of +1~-1°C The freeze symbol SNOWFLAK will be stable in case of outdoor temperature under -1.1°C Low Battery Condition Display The Indoor Display Console shows the Low Battery condition symbol batteryto remind you to change the batteries of the Indoor Display Console or the Outdoor Sensor when necessary Indoor Display Console Low Battery condition symbol battery- will be shown on the left hand side within the INDOOR section of the display Outdoor Sensor Low Battery condition symbol battery- will be shown on the left hand side within the OUTDOOR section of the display Indoor Display Console low battery condition displays within the indoor section. Outdoor Sensor low battery condition displays within the outdoor section Wireless Connection to Outdoor Sensor Press CHANNEL to select a channel. You can read the data of up to 3 Outdoor Sensors on one Indoor Display Console Press and hold CHANNEL for 3 seconds to search for outdoor sensor Additional tips: When placing both the inside and outside units remember they are subject to interference. Try to: a. Install both units as close as possible to each other. b. Avoid outside interference by not placing them near computers, TVs, etc. c. Concrete walls and floors can interrupt transmissions. d. If the connection is successful initially and then fails occasionally, try to reduce the distance between the units 7 of 8 City Locations The 26 cities of Australia and New Zealand Moon/Sun Rise/Set time is does not account for daylight savings. Add 1+ hour manually as necessary during daylight savings periods. For product updates, and country codes outside of Australia and New Zealand, visit www.holmanindustries.com.au/weather No. Country City 1 Sydney 2 Melbourne 3 Hobart 4 Adelaide 5 Perth 6 Darwin 7 Canberra 8 Townsville 9 Alice Springs 10 Cairns 11 Australia Broome 12 Geralton 13 Newcastle 14 Rockhampton 15 Mackay 16 Carnavon 17 Esperance 18 Albany 19 Mt. Gambier 20 Warrnambool 21 Albury 22 Brisbane 23 Auckland 24 New Zealand Wellington 25 Christchurch 26 Dunedin Abbreviation SYD MEL HBA ADL PER DRW CBR TSV ASP CNS BME GER NCL ROK MKY CAR EPR ALB MGM WMB AL BRS AKL WLG CHC DUD Should you have any questions about this product or its operation please telephone our customer service helpline on 1300 716 188. Head Office/Service 11 Walters Drive, Osborne Park WA 6017 Ph: +61 8 9416 9999 Fax: +61 8 9416 9920 service@holmanindustries.com.au 8 of 8 www.holmanindustries.com.au Copyright 2019 Holman IndustriesAdobe PDF Library 15.0 Adobe InDesign 16.3 (Macintosh)